This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Without this patch, signals sent during architecture specific signal
handling (typically as a result of the user's stack being inaccessible)
are ignored.
This is the SH version of commit c3ff8ec31c
which was for the i386.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.
With this change all SuperH Mobile devices now use the same clock code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.
While at it, fix up the VEU(2) interrupt vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is
By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize
By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for the single I2C channel on sh7366.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for the single I2C channel on sh7723.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for two I2C channels to the sh7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.
It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the following cleanups:
- make the following needlessly global code static:
- cf-enabler.c: cf_init()
- cpu/clock.c: __clk_enable()
- cpu/clock.c: __clk_disable()
- process_32.c: default_idle()
- time_32.c: struct clocksource_sh
- timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
- process_{32,64}.c: disable_hlt()
- process_{32,64}.c: enable_hlt()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently this is only linked in for CONFIG_BINFMT_ELF, make it dependent
on CONFIG_ELF_CORE, so it's both selectable there and also linked in for
CONFIG_BINFMT_ELF_FDPIC.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch provides an enhancement to kexec/kdump. It implements the
following features:
- Backup/restore memory used by the original kernel before/after
kexec.
- Save/restore CPU state before/after kexec.
The features of this patch can be used as a general method to call program in
physical mode (paging turning off). This can be used to call BIOS code under
Linux.
kexec-tools needs to be patched to support kexec jump. The patches and
the precompiled kexec can be download from the following URL:
source: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-src_git_kh10.tar.bz2
patches: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-patches_git_kh10.tar.bz2
binary: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec_git_kh10
Usage example of calling some physical mode code and return:
1. Compile and install patched kernel with following options selected:
CONFIG_X86_32=y
CONFIG_KEXEC=y
CONFIG_PM=y
CONFIG_KEXEC_JUMP=y
2. Build patched kexec-tool or download the pre-built one.
3. Build some physical mode executable named such as "phy_mode"
4. Boot kernel compiled in step 1.
5. Load physical mode executable with /sbin/kexec. The shell command
line can be as follow:
/sbin/kexec --load-preserve-context --args-none phy_mode
6. Call physical mode executable with following shell command line:
/sbin/kexec -e
Implementation point:
To support jumping without reserving memory. One shadow backup page (source
page) is allocated for each page used by kexeced code image (destination
page). When do kexec_load, the image of kexeced code is loaded into source
pages, and before executing, the destination pages and the source pages are
swapped, so the contents of destination pages are backupped. Before jumping
to the kexeced code image and after jumping back to the original kernel, the
destination pages and the source pages are swapped too.
C ABI (calling convention) is used as communication protocol between
kernel and called code.
A flag named KEXEC_PRESERVE_CONTEXT for sys_kexec_load is added to
indicate that the loaded kernel image is used for jumping back.
Now, only the i386 architecture is supported.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arch/mips/kernel/stacktrace.c: Heiko can't type
kthread: reduce stack pressure in create_kthread and kthreadd
fix core/stacktrace changes on avr32, mips, sh
This patch introduces the new syscall pipe2 which is like pipe but it also
takes an additional parameter which takes a flag value. This patch implements
the handling of O_CLOEXEC for the flag. I did not add support for the new
syscall for the architectures which have a special sys_pipe implementation. I
think the maintainers of those archs have the chance to go with the unified
implementation but that's up to them.
The implementation introduces do_pipe_flags. I did that instead of changing
all callers of do_pipe because some of the callers are written in assembler.
I would probably screw up changing the assembly code. To avoid breaking code
do_pipe is now a small wrapper around do_pipe_flags. Once all callers are
changed over to do_pipe_flags the old do_pipe function can be removed.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_pipe2
# ifdef __x86_64__
# define __NR_pipe2 293
# elif defined __i386__
# define __NR_pipe2 331
# else
# error "need __NR_pipe2"
# endif
#endif
int
main (void)
{
int fd[2];
if (syscall (__NR_pipe2, fd, 0) != 0)
{
puts ("pipe2(0) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
printf ("pipe2(0) set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0)
{
puts ("pipe2(O_CLOEXEC) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fixes this type of problem:
CC arch/s390/kernel/stacktrace.o
arch/s390/kernel/stacktrace.c:84: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:84: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:84: warning: parameter names (without types) in function declaration
arch/s390/kernel/stacktrace.c:97: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:97: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:97: warning: parameter names (without types) in function declaration
caused by "stacktrace: export save_stack_trace[_tsk]"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts sh to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single(). Not tested,
but it compiles.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
SH7763's setup code use old DECLARE_INTC_DESC.
There was a compile error because of this.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following build error caused by
commit a1dc4b59fa
(sh: intc_sh5 depends on cayman board for IRQ priority table.):
<-- snip -->
...
CC arch/sh/kernel/cpu/irq/intc-sh5.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c: In function 'plat_irq_setup':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c:257: error: expected declaration or statement at end of input
make[4]: *** [arch/sh/kernel/cpu/irq/intc-sh5.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was copied over from the previous MobileR bits, which doesn't
apply to R2. The URAM block on R2 is recycled for the L2 instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh7723 silicon with a prr value of 0x51.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a VPU vector typo for sh7723. The correct value is 0x980,
the same as for sh7722.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The USBF function on sh7722 is currently not working with the m66592_udc
driver. The driver is using platform_get_resource_byname() so my commit
a0d29798e5 broke sh7722 support.
The long term fix is to replace platform_get_resource_byname() in the
driver with platform_get_resource(), but this helps until that happens.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] return to old errno choice in mkdir() et.al.
[Patch] fs/binfmt_elf.c: fix wrong return values
[PATCH] get rid of leak in compat_execve()
[Patch] fs/binfmt_elf.c: fix a wrong free
[PATCH] avoid multiplication overflows and signedness issues for max_fds
[PATCH] dup_fd() part 4 - race fix
[PATCH] dup_fd() - part 3
[PATCH] dup_fd() part 2
[PATCH] dup_fd() fixes, part 1
[PATCH] take init_files to fs/file.c
There are a few different types of debug trap exceptions, though now
that they are all going through a special jump table, the restorer needs
to be unified as well.
Presently this is falling through the ret_from_fork path, which more or
less does the right thing on SH-3/4 whilst being completely unsuitable on
MMU-less targets.
Ultimately what we want here is a branch through the platform's
restore_all directly, without worrying about the retval being clobbered.
We can accomplish that through a branch to __restore_all directly, so
switch it so we come back from the jump table and branch to the restorer.
This fixes up a recursion in the nommu WARN_ON() path, as well as some
other userspace nastiness where said recursion caused serious stack
corruption.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently is_valid_bugaddr() is true for anything >= PAGE_OFFSET, which
happens to be 0 on nommu configurations. Make this a bit smarter by just
reading in the opcode and comparing it against the trap type that we
already know. Follows the logic from avr32.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Entry to resume_userspace expects r8 to contain current_thread_info,
which happens in all paths except for syscall_badsys, where r8 was
being inadvertently trampled. Reload it before the branch.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When using initramfs on systems that don't explicitly clear LOADER_TYPE,
unpack_to_rootfs() tramples tramples the range with the defaults taken
out of .empty_zero_page. This causes kernels with valid initramfs images
to bail out with crc or gzip magic mismatch errors after the second
unpack takes place on certain platform configurations.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some kernel and boot loader configurations tweak the .empty_zero_page
settings, while others do not. Print the values out on entry as a
debugging aid.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a common hex array in hexdump.c so everyone can use it.
Add a common hi/lo helper to avoid the shifting masking that is
done to get the upper and lower nibbles of a byte value.
Pull the pack_hex_byte helper from kgdb as it is opencoded many
places in the tree that will be consolidated.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'ix' is unsigned but denormal_subf1() may return a negative int.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The processor models sh7706, sh7707 and sh7709 don't support high
level trigger sense configuration. And the intc code looks like
crap these days so what's the difference.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clean up the intc tables by removing unneeded #ifdefs. The vector
list is what selects which interrupt sources that should be added,
having unsupported bitfields listed is ok as long as the vector
is excluded from the list.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds interrupt acknowledge code for external interrupt
sources on sh3 processors. Only really required for edge triggered
interrupts, but we ack regardless of sense configuration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch unifies the sh3 external irq pin code. It buys us some
savings with reduced code redundancy, but the main feature with
this change is irq sense selection support for all sh3 processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reset the transmitter and receiver when setting up early printk.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Drain by waiting for all characters to be sent, and make sure to
wait a little bit after setting up the baud rate.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use sci_out() instead of ctrl_outw() for early printk setup code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add physical memory resources such as System RAM, Kernel code/data/bss
and reserved crash dump area to /proc/iomem. Same strategy as on x86.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Do like everyone else and have a struct resource for kernel bss.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a proper prototype for __do_softirq() in include/linux/interrupt.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SH7723 is the first hard silicon to implement the L2, and unsurprisingly,
does the precise inverse of what the specification alleges. XOR the
URAM/L2 size bits to get back in line with the existing parsing logic.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-4A series probe we were relying on doesn't work any more on the
newer parts, bump this up to use CVR.CHIP instead so we have consistent
behaviour across all of the parts, which is what this should have been
testing in the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add platform data for the SuperH Mobile I2C block to sh7722.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use physical addresses and change resource name to follow data sheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for Solution Engine SH7721 board(MS7721RP01).
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
arch/sh/kernel/traps_32.c: In function `do_reserved_inst':
arch/sh/kernel/traps_32.c:667: error: implicit declaration of function `do_fpu_inst'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes some compile errors due to missing save_fpu()
prototypes on sh64 caused by
commit 9bbafce2ee
(sh: Fix occasional FPU register corruption under preempt).
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently with preempt enabled there's the possibility to be preempted
after the TIF_USEDFPU test and the register save, leading to bogus
state post-__switch_to(). Use an explicit preempt_disable()/enable()
pair around unlazy_fpu()/clear_fpu() to avoid this. Follows the x86
change.
Reported-by: Takuo Koguchi <takuo.koguchi.sw@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the SH-2/SH-2A address error exception dispatch copies off the
register state from the stack and skips over the first register, skewing
the rest. Fix up the math here so that the proper register state is
handed down to the exception handler itself.
Signed-off-by: Kieran Bingham <kbingham@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ERROR: "copy_page" [fs/unionfs/unionfs.ko] undefined!
like all the other architectures.
Cc: Erez Zadok <ezk@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the RTC resources setup for sh770x. Whit these proper
start values RTC driver (drivers/rtc/rtc-sh.c) works.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
drivers/char/pcmcia/synclink_cs.c:284:1: warning: "CCR3" redefined
In file included from include/asm/cache.h:13,
from include/asm/processor_32.h:15,
from include/asm/processor.h:60,
from include/linux/prefetch.h:14,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/char/pcmcia/synclink_cs.c:38:
include/asm/cpu/cache.h:38:1: warning: this is the location of the previous definition
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the maskreg irq code since it is not in use anymore.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The idea is that we want to get rid of the in/out/readb/writeb callbacks from
the machvec and replace that with simple inline read and write operations to
memory. Fast and simple for most hardware devices (think pci).
Some devices require special treatment though - like 16-bit only CF devices -
so we need to have some method to hook in callbacks.
This patch makes it possible to add a per-device trap generating filter. This
way we can get maximum performance of sane hardware - which doesn't need this
filter - and crappy hardware works but gets punished by a performance hit.
V2 changes things around a bit and replaces io access callbacks with a
simple minimum_bus_width value. In the future we can add stride as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the unaligned access handling code to use opcode_t
instead of u16. While at it, enable unaligned access handling for sh2a.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds byte support to the sign extension code. Unaligned access
traps should never be generated on 8-bit io operations, but we will use this
code for trapped io and we do need byte support there.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
move update_process_times() out from under xtime_lock.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break out the sign extension code since it's used in multiple places.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh7722 devices with prr value 0xa1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit d3d74453c3 ("hrtimer: fixup the
HRTIMER_CB_IRQSAFE_NO_SOFTIRQ fallback") broke several archs, and since
only Russell bothered to merge the fix, and Greg to ACK his arch, I'm
sending this for merger.
I have confirmation that the Alpha bit results in a booting kernel.
That leaves: blackfin, frv, sh and sparc untested.
The deadlock in question was found by Russell:
IRQ handle
-> timer_tick() - xtime seqlock held for write
-> update_process_times()
-> run_local_timers()
-> hrtimer_run_queues()
-> hrtimer_get_softirq_time() - tries to get a read lock
Now, Thomas assures me the fix is trivial, only do_timer() needs to be
done under the xtime_lock, and update_process_times() can savely be
removed from under it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Greg Ungerer <gerg@uclinux.org>
CC: Richard Henderson <rth@twiddle.net>
CC: Bryan Wu <bryan.wu@analog.com>
CC: David Howells <dhowells@redhat.com>
CC: Paul Mundt <lethal@linux-sh.org>
CC: William Irwin <wli@holomorphy.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using "attr" twice is not OK, because it effectively prohibits such
container_of() on variables not named "attr".
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the BOOTMEM_EXCLUSIVE, introduced in the previous patch, to avoid
conflicts while reserving the memory for the kdump capture kernel
(crashkernel=).
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch removes interrupt priority tables from the intc code.
Optimal priority assignment varies with embedded application anyway,
so keeping the interrupt priority tables together with cpu-specific
code doesn't make sense.
The function intc_set_priority() should be used instead to set the
desired interrupt priority level.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch provides specific clock support for the SH7712.
Signed-off-by: Andrew Murray <amurray@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in the L1I/L1D/L2 cache shape support to their respective
entries in the ELF auxvt, based on the Alpha implementation. We use
this on the userspace libc side for calculating a tightly packed
SHMLBA amongst other things.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently most of the 29-bit physical parts do P1/P2 segmentation
with a 1:1 cached/uncached mapping, jumping between the two to
control the caching behaviour. This provides the basic infrastructure
to maintain this behaviour on 32-bit physical parts that don't map
P1/P2 at all, using a shiny new linker section and corresponding
fixmap entry.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements kernel-level atomic rollback built on top of gUSA,
as an alternative non-IRQ based atomicity method. This is generally
a faster method for platforms that are lacking the LL/SC pairs that
SH-4A and later use, and is only supportable on legacy cores.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Shoves a magic word in to the empty_zero_page section for the
bootloader to work out whether to start the kernel in 29-bit
or 32-bit mode.
[ Renesas CPUs already take care of the initial PMB mappings entirely
in hardware and decide on 29-bit/32-bit physical depending on which
pin powered up the CPU, so this is mostly for ST parts. -- PFM ].
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
mem= can't be used to grow the size of kernel memory, so provide a
warning to that effect.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7263 (SH-2A) CPU.
This particular CPU is a superset of SH7203, adding some additional
peripheral blocks and hooking up additional (reserved on SH7203)
vectors in the INTC block.
No visibly nasty surprises, yet..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is trivial, in that they're both effectively the same for the base
relocations anyways. SH-5 doesn't need the unaligned bits, and has a
few extra relocations, which are never hit on non-SH5 parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ST40 stuff in-tree hasn't built for some time, and hasn't been
updated for over 3 years. ST maintains their own out-of-tree changes
and rebases occasionally, and that's ultimately where all of the ST40
users go anyways.
In order for the ST40 code to be brought up to date most of the stuff
removed in this changeset would have to be rewritten anyways, so there's
very little benefit in keeping the remnants around either.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently these are only being exported for CONFIG_CPU_SH4. This
invariably breaks when building for an SH-3 that includes multiple
targets in multilib.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was all reworked some time ago, the old debug_enter was ripped
out with everything going through a debug trap jump table instead.
Kill off the debug_enter target and reference kgdb_handle_exception
directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It's assumed that .eh_frame is terminated with 4-byte 0 in shared
libraries and executable. It seems to be the case for VDSOs too.
Without this terminator, I saw failures when unwinding from VDSO,
though I don't know how other architectures handle this issue.
For the normal libs, crtendS.o gives this terminator. We can use
such terminating objects. Or we can add a 4-byte 0 with modifying
the linker script like as the patch below.
Signed-off-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While using separate IRQ stacks can cut down on stack consumption,
many users can also use 4k stacks directly without the additional
need of separate stacks for soft and hardirqs.
With this split, we support the same rationale for 4KSTACKS as
m68knommu, with the IRQSTACKS abstraction as per ppc64.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some cleanups to the SH linker script. This reorders some of the
data sections for more optimal placement, general tabification,
and plugging in omitted generic definitions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When the SH kernel used to support embedding a ramdisk in the
pre-initramfs days it was placed in a special section and made to
look like a regular initrd. Since that was removed ages ago, kill
off the remaining cruft that was missed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
memory_end was being clobbered by whatever the kernel config had
specified, rather than obeying the setup option. Fix this up so
that memory_end is only initialized if nothing has been set on
the command line.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the crashkernel parsing from arch/sh/kernel/machine_kexec.c
and calls the generic function, introduced in the generic patch, in
setup_bootmem_allocator().
This is necessary because the amount of System RAM must be known in this
function now because of the new syntax.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the easiest things to isolate is the pid printed in kernel log.
There was a patch, that made this for arch-independent code, this one makes
so for arch/xxx files.
It took some time to cross-compile it, but hopefully these are all the
printks in arch code.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All asm/ipc.h files do only #include <asm-generic/ipc.h>.
This patch therefore removes all include/asm-*/ipc.h files and moves the
contents of include/asm-generic/ipc.h to include/linux/ipc.h.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This cleans up the formatting in the vDSO linker script, mostly just the
use of whitespace. It's intended to approximate the kernel standard
conventions for indenting C, treating elements of the linker script about
like initialized variable definitions.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical handlers of PTRACE_DETACH go into ptrace_request().
Not touching compat code.
Not touching archs that don't call ptrace_request.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (124 commits)
sh: allow building for both r2d boards in same binary.
sh: fix r2d board detection
sh: Discard .exit.text/.exit.data at runtime.
sh: Fix up some section alignments in linker script.
sh: Fix SH-4 DMAC CHCR masking.
sh: Rip out left-over nommu cond syscall cruft.
sh: Make kgdb i-cache flushing less inept.
sh: kgdb section mismatches and tidying.
sh: cleanup struct irqaction initializers.
sh: early_printk tidying.
video: pvr2fb: Add TV (RGB) support to Dreamcast PVR driver.
sh: Conditionalize gUSA support.
sh: Follow gUSA preempt changes in __switch_to().
sh: Tidy up gUSA preempt handling.
sh: __copy_user() optimizations for small copies.
sh: clkfwk: Support multi-level clock propagation.
sh: Fix URAM start address on SH7785.
sh: Use boot_cpu_data for CPU probe.
sh: Support extended mode TLB on SH-X3.
sh: Bump MAX_ACTIVE_REGIONS for SH7785.
...
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
As noted by Christoph Hellwig, pktgen was the only user so
it can now be removed.
[ Add missing cases caught by Adrian Bunk. -DaveM ]
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were previously discarded at link time, though as with MIPS
we keep them around until runtime to satisfy .rodata references.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the PERCPU() macro introduction .data.cacheline_aligned was
inhereting PAGE_SIZE alignment, fix that up for L1_CACHE_BYTES
again. Likewise, the initramfs section wants PAGE_SIZE alignment.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
At some point way back when (2.5 or so) quite a few syscalls hadn't
yet been wired up as cond_syscalls(), so we opted to just do direct
sys_ni_syscall wrapping in the assembly code instead. That's all
been fixed up since then, so we can drop the wrapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
kgdb had its own ranged I-cache flushing routine that attempted to
duplicate the flush_icache_range() functionality, but managed to do
an explicit D-cache writeback & invalidate twice on SH-4. This is
a no-op for SH-3, and the flush_icache_range() semantics already do
what kgdb was feebly attempting to do already, so just move over to
that and kill off the wrapper.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The kgdb console setup was callable from a left-over deferred
initialization path, which in turn depends on __init symbols. Since
the deferred initialization was removed some time ago, kill off the
rest of those remnants and move kgdb_init() and friends to __init.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
setup_early_printk() can be static, and with that, we can kill off
the early initialization variable and move the CON_BOOT check in
to the function body.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This conditionalizes gUSA support. gUSA is not supported on
SMP configurations, and it's not necessary there anyways due
to having other atomicity options (ie, movli.l/movco.l).
Anything implementing the LL/SC semantics (all SH-4A CPUs)
can switch to userspace atomicity implementations without
requiring gUSA. This is left default-enabled on all UP so
that glibc doesn't break.
Those that know what they are doing can disable this explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently gUSA toggles hardirqs to disable preemption in the signal
handler. Make the preemption toggling explicit, and kill off some
CONFIG_PREEMPT ifdefs in the process.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently clock propagation only works for one level, but we have some
clocks which need to propagate multiple levels, so make this recursive.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Not all of the SH-X2 URAM blocks are mapped in the same place,
SH7785 happens to map it on the opposite end of the address space
from SH7722, correct the addresses.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves off of smp_processor_id() and only sets the probe
information for the boot CPU directly. This will be copied out
for the secondaries, so there's no reason to do this each time.
This also allows for some header tidying.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was some debug code left in here that caused the pin changes
to never be hit. Kill that off, and all is well.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The probing logic works for both URAM and L2, with no way to
distinguish between the two. Disable the probing for now and
let the CPU subtypes that have this in a real L2 configuration
explicitly say so.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds basic support for SH-X3 SMP (4 CPUs).
More IPI and cache debugging is necessary, mostly interfacing the
d-cache coherency and the I-cache broadcast invalidates. Only for
testing at present!
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a very preliminary bunch of SMP code scattered around for the
SH7604 microcontrollers from way back when, and it has mostly suffered
bitrot since then. With the tree already having been slowly getting
prepped for SMP, this plugs in most of the remaining platform-independent
bits.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SMP INTC (particularly
INTC2) controllers.
These are largely implemented as conventional blocks, with
register sets grouped together at fixed strides relative to
the CPU id.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds the TLB flushing routines for SMP systems, based on
the MIPS implementation, with some additional SH-specific
flush routines.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the cpu_data definitions and gets rid of the special
boot_cpu_data. It's made a wrapper to the boot CPU, in order to keep
the existing in-tree users happy.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The cpufreq driver banner is currently printed for each CPU, move
it down so it's not as noisy and it's only printed once.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the following fixes and improvements:
- Fix address typo for INTMSK2 / INTMSKCLR2 registers on sh7780.
- Adds IRQ_MODE_IRLnnnn_MASK using intc controller for IRL masking.
- Good old IRQ_MODE_IRLnnnn should not register any intc controller.
- plat_irq_setup_pins() now selects IRL or IRQ mode.
- the holding function is now disabled using ICR0.
By default all external pin interrupts are disabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All processor specific interrupt code is now converted to make use
of the new intc code. The config option CONFIG_CPU_HAS_INTC_IRQ is
because of that pointless.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
