This will convert remaining non-obvious or naive calculations of array
sizes to use ARRAY_SIZE() macro.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/ucc_geth.c: In function 'ucc_geth_rx':
drivers/net/ucc_geth.c:3483: error: 'dev' undeclared (first use in this function)
drivers/net/ucc_geth.c:3483: error: (Each undeclared identifier is reported only once
drivers/net/ucc_geth.c:3483: error: for each function it appears in.)
make[2]: *** [drivers/net/ucc_geth.o] Error 1
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Protect all new napi function calls with CONFIG_GFAR_NAPI. Otherwise
the driver will stop working when CONFIG_GFAR_NAPI disabled.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update AU1000 get_ethernet_addr().
Three functions were brought together in one.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
General cleanups mostly as suggested by checkpatch plus getting rid of
homebrew version of offsetof().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Caused by "[NET]: Introduce and use print_mac() and DECLARE_MAC_BUF()"
aka 0795af5729.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With the base stored in dcr_host_t, there's no need for callers to pass
the dcr_n into dcr_unmap(). In fact this removes the possibility of them
passing the incorrect value, which would then be iounmap()'ed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that all users of dcr_read()/dcr_write() add the dcr_host_t.base, we
can save them the trouble and do it in dcr_read()/dcr_write().
As some background to why we just went through all this jiggery-pokery,
benh sayeth:
Initially the goal of the dcr_read/dcr_write routines was to operate like
mfdcr/mtdcr which take absolute DCR numbers. The reason is that on 4xx
hardware, indirect DCR access is a pain (goes through a table of
instructions) and it's useful to have the compiler resolve an absolute DCR
inline.
We decided that wasn't worth the API bastardisation since most places
where absolute DCR values are used are low level 4xx-only code which may
as well continue using mfdcr/mtdcr, while the new API is designed for
device "instances" that can exist on 4xx and Axon type platforms and may
be located at variable DCR offsets.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This requires us to do a sort-of fake dcr_map(), so that base is set
properly. This will be fixed/removed when the device-tree-aware emac driver
is merged.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that dcr_host_t contains the base address, we can use that in the
ibm_newemac code, rather than storing it separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bea3348eef broke the build of tc35815.c
for the non-NAPI case:
CC drivers/net/tc35815.o
drivers/net/tc35815.c: In function 'tc35815_interrupt':
drivers/net/tc35815.c:1464: error: redefinition of 'lp'
drivers/net/tc35815.c:1443: error: previous definition of 'lp' was here
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix build breakage by the recent statistics cleanup in cset
09f75cd7bf.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New version which uses less locking and drops old API
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update myri10ge firmware headers to latest upstream version with
TSO6 and RSS support.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix one comment in myri10ge.c and update indendation and white spaces
to match the code generated by indent from upstream CVS.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the "don't change MAC of slaves" functionality added in
previous changes to be a generic option, rather than something tied to
IB devices, as it's occasionally useful for regular ethernet devices as
well.
Adds "fail_over_mac" option (which is automatically enabled for IB
slaves), applicable only to active-backup mode.
Includes documentation update.
Updates bonding driver version to 3.2.0.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When bonding enslaves non Ethernet devices it takes pointers to functions
in the module that owns the slaves. In this case it becomes unsafe
to keep the bonding master registered after last slave was unenslaved
because we don't know if the pointers are still valid. Destroying the bond when slave_cnt is zero
ensures that these functions be used anymore.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Delay sending a gratuitous_arp when LINK_STATE_LINKWATCH_PENDING bit
in dev->state field is on. This improves the chances for the arp packet to
be transmitted.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bonding sometimes uses Ethernet constants (such as MTU and address length) which
are not good when it enslaves non Ethernet devices (such as InfiniBand).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow to enslave devices when the bonding device is not up. Over the discussion
held at the previous post this seemed to be the most clean way to go, where it
is not expected to cause instabilities.
Normally, the bonding driver is UP before any enslavement takes place.
Once a netdevice is UP, the network stack acts to have it join some multicast groups
(eg the all-hosts 224.0.0.1). Now, since ether_setup() have set the bonding device
type to be ARPHRD_ETHER and address len to be ETHER_ALEN, the net core code
computes a wrong multicast link address. This is b/c ip_eth_mc_map() is called
where for multicast joins taking place after the enslavement another ip_xxx_mc_map()
is called (eg ip_ib_mc_map() when the bond type is ARPHRD_INFINIBAND)
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for enslaving netdevices which do not support
the set_mac_address() function. In that case the bond mac address is the one
of the active slave, where remote peers are notified on the mac address
(neighbour) change by Gratuitous ARP sent by bonding when fail-over occurs
(this is already done by the bonding code).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch changes some of the bond netdevice attributes and functions
to be that of the active slave for the case of the enslaved device not being
of ARPHRD_ETHER type. Basically it overrides those setting done by ether_setup(),
which are netdevice **type** dependent and hence might be not appropriate for
devices of other types. It also enforces mutual exclusion on bonding slaves
from dissimilar ether types, as was concluded over the v1 discussion.
IPoIB (see Documentation/infiniband/ipoib.txt) MAC address is made of a 3 bytes
IB QP (Queue Pair) number and 16 bytes IB port GID (Global ID) of the port this
IPoIB device is bounded to. The QP is a resource created by the IB HW and the
GID is an identifier burned into the HCA (i have omitted here some details which
are not important for the bonding RFC).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_enable_device() is __must_check so do that in natsemi_resume().
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unless we have failed to fill the RX ring the timer used by the natsemi
driver is not particularly urgent and can use round_jiffies() to allow
grouping with other timers.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The call to napi_disable() in the PCI shutdown handler is problematic,
and is aggravated by the new NAPI.
Also, make sure watchdog timer doesn't go off.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
if your mask is host-endian, you should apply it after le64_to_cpu();
if it's little-endian - before. Doing both (for the same mask and
little-endian value) is broken.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
deal with signedness of the stuff passed to set_bit() et.al.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... since that sucker is not 32bit-only and on 64bit skb->tail is an
offset, not a pointer.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3d73c288 ("mlx4_core: Fix section mismatches") introduced a
stupid bug in device init: when some of mlx4_init_one() was split off
into __mlx4_init_one(), the call from the main mlx4_init_one()
function was back to mlx4_init_one() rather than to __mlx4_init_one(),
which leads to an obvious infinite loop if the function is every
called.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
b43 wireless needs <linux/io.h>
linux/drivers/net/wireless/b43/pio.h: In function 'b43_pio_write':
linux/drivers/net/wireless/b43/pio.h:89: error: implicit declaration of function 'mmiowb'
linux/drivers/net/wireless/b43/phy.c: In function 'b43_phy_write':
linux/drivers/net/wireless/b43/phy.c:301: error: implicit declaration of function 'mmiowb'
linuxdrivers/net/wireless/b43/sysfs.c: In function 'b43_attr_interfmode_store':
linuxdrivers/net/wireless/b43/sysfs.c:147: error: implicit declaration of function 'mmiowb'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
A number of different drivers incorrect access the kobject name field
directly. This is not correct as the name might not be in the array.
Use the proper accessor function instead.
Need to read and store sblk->status_idx before checking for more work.
The status idx is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When completing bnx2_poll(), we should always break out of the while
loop and return work_done instead of returning 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to read and store sblk->status_tag before checking for more work.
The status tag is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When we detect tx error, it is more correct to return the rx
work_done so far instead of 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
