Adds the platform device definitions and the architecture specific support
routines (i.e. register initialization and descriptor formats) for the
iop-adma driver.
Changelog:
* add support for > 1k zero sum buffer sizes
* added dma/aau platform devices to iq80321 and iq80332 setup
* fixed the calculation in iop_desc_is_aligned
* support xor buffer sizes larger than 16MB
* fix places where software descriptors are assumed to be contiguous, only
hardware descriptors are contiguous for up to a PAGE_SIZE buffer size
* convert to async_tx
* add interrupt support
* add platform devices for 80219 boards
* do not call platform register macros in driver code
* remove switch() statements for compatible register offsets/layouts
* change over to bitmap based capabilities
* remove unnecessary ARM assembly statement
* checkpatch.pl fixes
* gpl v2 only correction
* phys move to dma_async_tx_descriptor
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
WARNING: arch/arm/mach-iop13xx/built-in.o - Section mismatch: reference to
.init.text:iop13xx_pcie_map_irq from .text between 'iop13xx_pci_setup' (at
offset 0x7fc) and 'iop13xx_map_pci_memory'
While fixing this warning I also recalled Adrian Bunk's recommendation to
not use inline in .c files, as 'iop13xx_map_pci_memory' is needlessly
inlined.
Removing 'inline' uncovered some dead code so that is cleaned up as well.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the iop3xx platform support code assumes that RedBoot is the
bootloader and has already initialized the ATU. Linux should handle this
initialization for three reasons:
1/ The memory map that RedBoot sets up is not optimal (page_to_dma and
virt_to_phys return different addresses). The effect of this is that using
the dma mapping API for the internal bus dma units generates pci bus
addresses that are incorrect for the internal bus.
2/ Not all iop platforms use RedBoot
3/ If the ATU is already initialized it indicates that the iop is an add-in
card in another host, it does not own the PCI bus, and should not be
re-initialized.
Changelog:
* rather than change nr_controllers to zero, simply do not call
pci_common_init
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* architecture specific details are handled in asm/arch/time.h
* ARCH_IOP13XX now selects PLAT_IOP
* as suggested by Lennert use ifdef CONFIG_XSCALE to skip the cp_wait on
XSC3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the iop32x code isn't iop321-specific, and the iop33x code isn't
iop331-specfic, do a s/iop321/iop32x/ and s/iop331/iop33x/, and tidy up
the code to conform to the coding style guidelines somewhat better.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Revamp the iop3xx board support: move the support code for each iop
board type into its own file, start using platform serial and platform
physmap flash devices, switch to a per-board time tick rate, and get
rid of the ARCH_EP80219 and STEPD config options by doing the relevant
checks at run time.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
