Add vendor/product IDs for new no name dm9601 compatible usb ethernet
adaptors.
Reported-by: Eric Lauriault <eric@linux.ca>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the zaurus driver can
properly handle this combined device.
Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make usbnet_get_link() fall back to ethtool_op_get_link() instead of
defaulting to 1.
This makes usbnet_get_link return valid results without the need for a
driver specific check_connect or mii ops as long as the driver calls
netif_carrier_{on,off}() as appropriate. cdc_ether is an example of
such a driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up. This patch adds the device id to cdc_ether.c as a workaround.
Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c. See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two new device ids to the asix driver.
One comes directly from the asix driver on their web site, the other was
reported by Armani Liao as needed for the MSI X320 to get the driver to
work properly for it.
Reported-by: Armani Liao <aliao@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a few device ID's. It also removes an ID that was used
in an internal engineering version of a device and will never see
commercial light. Even if this ID will be 'recycled' in the future,
which is very unlikely, we don't know what kind of device will be
behind it. Therefore it's safer to remove it.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mcs7830_set_reg() and mcs7830_get_reg() are called with buffers
from stack which must not be used directly for USB transfers.
This causes corruption of the stack particulary on non x86
architectures because DMA may be used for these transfers.
Signed-off-by: Christian Eggers <christian.eggers@kathrein.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (95 commits)
b44: GFP_DMA skb should not escape from driver
korina: do not use IRQF_SHARED with IRQF_DISABLED
korina: do not stop queue here
korina: fix handling tx_chain_tail
korina: do tx at the right position
korina: do schedule napi after testing for it
korina: rework korina_rx() for use with napi
korina: disable napi on close and restart
korina: reset resource buffer size to 1536
korina: fix usage of driver_data
bnx2x: First slow path interrupt race
bnx2x: MTU Filter
bnx2x: Indirection table initialization index
bnx2x: Missing brackets
bnx2x: Fixing the doorbell size
bnx2x: Endianness issues
bnx2x: VLAN tagged packets without VLAN offload
bnx2x: Protecting the link change indication
bnx2x: Flow control updated before reporting the link
bnx2x: Missing mask when calculating flow control
...
This patch is for Alan Cox as it related to the tty layer.
Hopefully the hso driver is again relatively stable with this fix.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HSO changes for kref introduced a recursive spinlock take. All
functions which call put_rxbuf_data already have serial->serial_lock
grabbed.
[Comment to code added-AC]
Signed-off-by: Denis Joseph Barrow <D.Barrow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Filip Aben says this fix is neccessary for big endian machines.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the pegasus driver to use of the new net_device_ops structure
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the kaweth ethernet USB driver to netdevops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add warnings on invalid mac address to help disclose/debug problems.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise unicast RX will only work in promisc mode.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to take the address of the function params or local variables
when the direct value byteswapping routines are available.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cheap devices ship with dangling EEPROM pins!
They always return invalid address ff:ff:ff:ff:ff:ff.
Inherit the auto-generated address in this case,
so that these products can work with zero configuration.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed incorrect check for the modem port, this prevents
crashes caused by issueing a tiocmget_submit_urb
on endpoints which don't exist for non modem devices.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes TIOCM ioctls for Data Carrier Detect & related functions
work like /drivers/serial/serial-core.c potentially needed
for pppd & similar user programs.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Init the tty structure once
Don't set ->low_latency twice in a row
Don't force bits we should be leaving to the user
Don't allocate termios arrays as these are in fact allocated by the tty layer
for you and just overwrite the ones allocated in the driver
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checking tty == NULL doesn't help us unless we have a clear semantic for
the locking of the tty object in the driver. Use the tty kref objects so that
we can take references to the tty in the USB event handling paths.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
In drivers/net/wireless/zd1211rw/zd_usb.c the code:
(endpoint->bEndpointAddress & USB_TYPE_MASK) == USB_DIR_OUT
is suspicious. If it is intended to use USB_ENDPOINT_DIR_MASK rather than
USB_TYPE_MASK, then the whole conditional test could be converted to a call
to usb_endpoint_is_bulk_in.
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag marking a device running must be set before the URBs for
recption are submitted or they may complete too early and fail to resubmit.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB is going to switch the signature of the callbacks to
void callback(struct urb *urb, int status)
This patch will ease the transition.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 4 drivers have identical full duplex flow control resolution
functions. This patch changes them all to use one common function.
The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.
The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Made usb_drivers reset_resume function point to hso_resume this
fixes problems a usb reset is done when the network interface
is left idle for a few minutes. Possibly reset_resume should
initialise hardware more but this works in the common case.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes TIOCM ioctls for Data Carrier Detect & related functions
work like /drivers/serial/serial-core.c potentially needed
for pppd & similar user programs.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new structure hso_mutex_table had to be declared statically
& used as as hso_device mutex_lock(&serial->parent->mutex) etc
is freed in hso_serial_open & hso_serial_close by kref_put while
the mutex is still in use.
This is a substantial change but should make the driver much stabler.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added check for IFF_UP in hso_resume, this should eliminate -EINVAL (-22)
errors caused from urb's being submitted twice, once by hso_resume
& once in hso_net_open, if suspend/resume USB power saving mode is enabled
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved serial_open_count in hso_serial_open to
prevent crashes owing to the serial structure being made NULL
when hso_serial_close is called even though hso_serial_open
returned -ENODEV, Alan Cox pointed out this happens,
also put in sanity check in hso_serial_close
to check for a valid serial structure which should prevent
the most reproducable crash in the driver when the hso device
is disconnected while in use.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN9500 supports tx checksum offload, which slightly decreases cpu
utilisation. The benefit isn't very large because we still require
the skb to be linearized, but it does save a few cycles.
This patch adds support for it, and enables it by default.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add AX_MEDIUM_ENCK also when speed = 10/100Mbps. This allows my belkin
f5d5055 to work with my 100Mbps switch and with an old 10Mbps ISA card.
Without this patch, the card is recognized and the interface is brought
up fine, but no packets actually flow through the interface.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make pegasus driver not allocate a workqueue until the driver
is bound to some device, which will need that workqueue if
the device is brought up. This conserves resources when the
driver is linked but there's no pegasus device connected.
Also shrink the runtime footprint a smidgeon by moving some
init-only code into its proper section, and move an obnoxious
(frequent and meaningless) message to be debug-only.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to drivers/net/usb/asix.c for the Cables-to-Go "USB 2.0 to
10/100 Ethernet Adapter". USB id 0b95:772a.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yup, this appears to be the problem, thanks. I think &hso_net->net->dev
is more intuitive for the error message, so I've used that. I've also
added missing line endings on the error messages and set our local
rfkill structure element to NULL on failure so we don't try to call
rfkill_unregister on driver removal if we failed to register at all.
The patch below Works For Me (TM); the device is detected fine, can be
removed without problems and connects ok. I'll have a prod at why the
rfkill stuff isn't working next, but I believe this cleanup of the error
handling is appropriate no matter what the issue with registration is.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
