Make the following functions deal with ata_link instead of ata_port.
* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead
of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple links and different number of devices per link should be
considered to iterate over links and devices. This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().
This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such
changes have been examined and nothing should be broken.
While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In most cases, when EH is scheduled, all in-flight commands are
aborted causing EH to kick in immediately. However, in some cases
(especially with PMP), it's unclear which commands are affected by the
error condition and although aborting all in-flight commands work, it
isn't optimal and may cause unnecessary disruption. On the other
hand, waiting for in-flight commands to drain themselves can take up
to 30seconds.
This patch implements EH fast drain to handle such situations. It
gives in-flight commands some time to finish up but doesn't wait for
too long. After EH is scheduled, fast drain timer is started and if
no other completion occurs in ATA_EH_FASTDRAIN_INTERVAL all in-flight
commands are aborted. If any completion occurred in the interval, the
port is given another interval to finish up itself.
Currently ATA_EH_FASTDRAIN_INTERVAL is 3 secs which should be enough
for finishing up most commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If SError isn't accessible, EH can't tell whether hotplug has happened
or not. Report SError read failure with AC_ERR_OTHER and schedule
probing with hardreset. This will be mainly useful for PMPs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_EHI_HOTPLUGGED is a hint for reset functions indicating the the
port might have gone through hotplug/unplug just before entering EH.
Reset functions modify their behaviors a bit to handle the situation
better - e.g. using longer debouncing delay.
Currently, once HOTPLUG is set, it isn't cleared till the end of EH.
This is unnecessary and makes EH take longer. Clear the HOTPLUGGED
flag after a reset try (successful or not).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Debouncing failure is a good indicator of basic link problem. Use
-EPIPE to indicate debouncing failure and make ata_eh_reset() invoke
sata_down_spd_limit() if the error occurs during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_down_spd_limit() first reads the current SPD from SStatus and
limit the speed to the lower one of one below the current limit or one
below the current SPD in SStatus. SPD may not be accessible or valid
when SPD down is requested making sata_down_spd_limit() fail when it's
most needed.
This patch makes the current SPD cached after each successful reset
and forces GEN I speed (1.5Gbps) if neither of SStatus or the cached
value is valid, so sata_down_spd_limit() is now guaranteed to lower
the speed limit if lower speed is available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When an NCQ command fails, all commands in flight are aborted and the
offending one is reported using log page 10h. Depending on controller
characteristics and LLD implementation, all commands may appear as
having a device error due to shared TF status making it hard to
determine what's actually going on.
This patch adds AC_ERR_NCQ, marks the command reported by log page 10h
with it and print extra "<F>" after the error report for the command
to help distinguishing the offending command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Requiring LLDs to format multiple error description messages properly
doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation. __ata_ehi_push_desc() is the raw
version without the automatic separator.
While at it, make ehi_desc interface proper functions instead of
macros.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_eh_handle_dev_fail() from ata_eh_recover(). This is
in preparation of ata_link and PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement _GTM/_STM support. acpi_gtm is added to ata_port which
stores _GTM parameters over suspend/resume cycle. A new hook
ata_acpi_on_suspend() is responsible for storing _GTM parameters
during suspend. _STM is executed in ata_acpi_on_resume(). With this
change, invoking _GTF is safe on IDE hierarchy and acpi_sata check
before _GTF is removed.
ata_acpi_gtm() and ata_acpi_stm() implementation is taken from Alan
Cox's pata_acpi implementation. ata_acpi_gtm() is fixed such that the
result parameter is not shifted by sizeof(union acpi_object).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reimplements ACPI invocation such that, instead of
exporting ACPI details to the rest of libata, ACPI event handlers -
ata_acpi_on_resume() and ata_acpi_on_devcfg() - are used. These two
functions are responsible for determining whether specific ACPI method
is used and when.
On resume, _GTF is scheduled by setting ATA_DFLAG_ACPI_PENDING device
flag. This is done this way to avoid performing the action on wrong
device device (device swapping while suspended).
On every ata_dev_configure(), ata_acpi_on_devcfg() is called, which
performs _SDD and _GTF. _GTF is performed only after resuming and, if
SATA, hardreset as the ACPI spec specifies. As _GTF may contain
arbitrary commands, IDENTIFY page is re-read after _GTF taskfiles are
executed.
If one of ACPI methods fails, ata_acpi_on_devcfg() retries on the
first failure. If it fails again on the second try, ACPI is disabled
on the device. Note that successful configuration clears ACPI failed
status.
With all feature checks moved to the above two functions,
do_drive_set_taskfiles() is trivial and thus collapsed into
ata_acpi_exec_tfs(), which is now static and converted to return the
number of executed taskfiles to be used by ata_acpi_on_resume(). As
failures are handled properly, ata_acpi_push_id() now returns -errno
on errors instead of unconditional zero.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When EH gives up after repeated exceptions, it doesn't't clear the
PENDING bit on exit which leaves PENDING bit set without EH actually
scheduled. This makes ata_port_wait_eh() to wait forever makes rmmod
hang on such port. Fix it by clearing the flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
prereset() is now allowed to set flag for unsupported reset method.
EH layer is responsible for selecting the fallback. Remove non-sense
warning message.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After certain errors, some devices report complete garbage on
IDENTIFY. This can cause ata_dev_read_id() to fail with -EINVAL
resulting in immediate disabling of the device. Give the device one
last chance after -EINVAL to allow recovery from such situations. As
-EINVAL is triggered very rarely, this shouldn't cause any noticeable
affect on more common error paths.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Harald Dunkel <harald.dunkel@t-online.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata enables SCSI host during ATA host activation which happens
after IRQ handler is registered and IRQ is enabled. All ATA ports are
in frozen state when IRQ is enabled but frozen ports may raise limited
number of IRQs after being frozen - IOW, ->freeze() is not responsible
for clearing pending IRQs. During normal operation, the IRQ handler
is responsible for clearing spurious IRQs on frozen ports and it
usually doesn't require any extra code.
Unfortunately, during host initialization, the IRQ handler can end up
scheduling EH for a port whose SCSI host isn't initialized yet. This
results in OOPS in the SCSI midlayer. This is relatively short window
and scheduling EH for probing is the first thing libata does after
initialization, so ignoring EH scheduling until initialization is
complete solves the problem nicely.
This problem was spotted by Berck E. Nash in the following thread.
http://thread.gmane.org/gmane.linux.kernel/519412
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.
* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.
* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.
* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata previously depended upon waits in prereset to get resets after
hotplug right for both spin up and device ready wait. This was
necessary both for reliablity and speed as reset was likely to fail if
initiated too early and each try usually took more than 30secs to
fail. Previous patches fixed the reliability part by fixing status
and SCR handling in resets. This patch remedies the speed part by
improving reset sequencing.
Prereset waiting timeout is adjusted to 10s because spinup wait is
replaced by reset sequencing and !BSY wait is not as important as
before. During boot or module loading where the drive is already
fully spun up, !BSY wait succeeds immediately, so 10s should be enough
in most cases. It matters after hotplugging or other error
conditions, but in those cases, !BSY wait in prereset simply can't be
relied upon due to the varied and weird behaviors ATA controllers and
devices show.
Reset is now driven by ata_eh_reset_timeouts[] table which contains
timeouts for each reset try. The first reset can be softreset but the
following ones are always hardreset if available. Each timeout
defines deadline for the reset try. If a reset try fails, reset is
retried with the next timeout till the end of the timeout table is
reached. If a reset try fails before the timeout with error, libata
waits till the deadline of the failed try before retrying.
IOW, the timeout table defines timetable of reset tries such that the
n'th try always begins at least after the sum of all previous timeouts
has passed. The current timetable defines 4 tries and takes around 1
minute.
@0 : First try. This should succeed most of the time during boot.
@10 : 10s is enough to spin up most consumer harddrives. Give it
another shot.
@20 : 20s should spin up > 99% of working drives. This has 30s
timeout for retarded devices needing long idleness post reset.
@55 : Final try with 5s timeout just in case.
The above timetable is trade off between not annoying the device too
much with frequent resets and taking reasonable amount of time in most
cases. Some controllers may do better with shorter timeouts while
others may fare better with longer but we just can't rely upon LLD
writers to test each controller with wide variety of devices using
various scenarios. We need default behavior which reasonably fits
most cases.
I've tested the above timetable on a dozen SATA controllers and a few
PATA controllers with about a dozen different drives from all major
vendors and 4 different ODDs from three different vendors for both
boot and hotplug (if available) cases.
Boot probing is not affected unless the device is broken in which
cases new code gives up on the port after a minute rather than five or
nine minutes. When hotplugging, most devices get detected on the
first or second try. Multi-platter drives with long spin up time
which sometimes took > 40 secs with the original code, now usually
comes up during the second try and at least right after the third try
@20.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function. This patch is in preparation for EH timing
improvements.
* ata_wait_ready() never does busy sleep. It's only used from EH and
no wait in EH is that urgent. This function also prints 'be
patient' message automatically after 5 secs of waiting if more than
3 secs is remaining till deadline.
* ata_bus_post_reset() now fails with error code if any of its wait
fails. This is important because earlier reset tries will have
shorter timeout than the spec requires. If a device fails to
respond before the short timeout, reset should be retried with
longer timeout rather than silently ignoring the device.
There are three behavior differences.
1. Timeout is applied to both devices at once, not separately. This
is more consistent with what the spec says.
2. When a device passes devchk but fails to become ready before
deadline. Previouly, post_reset would just succeed and let
device classification remove the device. New code fails the
reset thus causing reset retry. After a few times, EH will give
up disabling the port.
3. When slave device passes devchk but fails to become accessible
(TF-wise) after reset. Original code disables dev1 after 30s
timeout and continues as if the device doesn't exist, while the
patched code fails reset. When this happens, new code fails
reset on whole port rather than proceeding with only the primary
device.
If the failing device is suffering transient problems, new code
retries reset which is a better behavior. If the failing device is
actually broken, the net effect is identical to it, but not to the
other device sharing the channel. In the previous code, reset would
have succeeded after 30s thus detecting the working one. In the new
code, reset fails and whole port gets disabled. IMO, it's a
pathological case anyway (broken device sharing bus with working
one) and doesn't really matter.
* ata_bus_softreset() is changed to return error code from
ata_bus_post_reset(). It used to return 0 unconditionally.
* Spin up waiting is to be removed and not converted to honor
deadline.
* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate ATA_EHI_DID_RESET into ATA_EHI_DID_SOFTRESET and
ATA_EHI_DID_HARDRESET. ATA_EHI_DID_RESET is redefined as OR of the
two flags. This patch doesn't introduce any behavior change. This
will be used later to determine whether _SDD is necessary or not.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
->cable_detect() used to be called on by the old ata_bus_probe() path.
Add invocation to ata_eh_revalidate_and_attach() right after IDENTIFYs
are done.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
->post_internal_cmd is simplified EH for internal commands. Its
primary mission is to stop the controller such that no rogue memory
access or other activities occur after the internal command is
released. It may provide error diagnostics by setting qc->err_mask
but this hasn't been a requirement.
To ignore SETXFER failure for CFA devices, libata needs to know
whether a command was failed by the device or for any other reason.
ie. internal command needs to get AC_ERR_DEV right.
This patch makes the following changes to AC_ERR_DEV handling and
->post_internal_cmd semantics to accomodate this need and simplify
callback implementation.
1. As long as the correct bits in the result TF registers are set,
there is no need to set AC_ERR_DEV explicitly. libata EH core
takes care of that for both normal and internal commands.
2. The only requirement for ->post_internal_cmd() is to put the
controller into quiescent state. It needs not to set any err_mask.
3. ata_exec_internal_sg() performs minimal error analysis such that
AC_ERR_DEV is automatically set as long as result_tf is filled
correctly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There was a rare report where SB600 reported SERR_INTERNAL and SRST
couldn't get it out of the failure mode. Hardreset on SERR_INTERNAL.
As the problem is intermittent, whether this fixes the problem or not
hasn't been verified yet, but hardresetting the channel on internal
error is a good idea anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
patch 2/4:
Clear tf before doing request sense.
This fixes the AOpen 56X/AKH timeout problem.
(http://bugzilla.kernel.org/show_bug.cgi?id=8244)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For drive side cable detection to work correctly, drives need to be
identified backwards such that the slave device releases PDIAG- before
the mater drive tries to detect cable type. ata_bus_probe() was fixed
by commit f31f0cc2f0 but the new EH path
wasn't fixed. This patch makes new EH path do IDENTIFY backwards.
ata_dev_configure() for new devices are still performed master first.
This is to keep the detection messages in forward order.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
->prereset() returns -ENOENT to tell libata that the port is empty and
reset sequencing should be stopped. This is not an error condition.
Update ata_eh_reset() such that it sets device classes to ATA_DEV_NONE
and return success in on -ENOENT. This makes spurious error message
go away.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conditionalize all PM related stuff in libata core layer using
CONFIG_PM.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port has two different id fields - id and port_no. id is
system-wide 1-based unique id for the port while port_no is 0-based
host-wide port number. The former is primarily used to identify the
ATA port to the user in printk messages while the latter is used in
various places in libata core and LLDs to index the port inside the
host.
The two fields feel quite similar and sometimes ap->id is used in
place of ap->port_no, which is very difficult to spot. This patch
renames ap->id to ap->print_id to reduce the possibility of such bugs.
Some printk messages are adjusted such that id string (ata%u[.%u])
isn't printed twice and/or to use ata_*_printk() instead of hardcoded
id format.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current EH speed down code is more of a proof that the EH
framework is capable of adjusting transfer speed in response to error.
This patch puts some intelligence into EH speed down sequence. The
rules are..
* If there have been more than three timeout, HSM violation or
unclassified DEV errors for known supported commands during last 10
mins, NCQ is turned off.
* If there have been more than three timeout or HSM violation for known
supported command, transfer mode is slowed down. If DMA is active,
it is first slowered by one grade (e.g. UDMA133->100). If that
doesn't help, it's slowered to 40c limit (UDMA33). If PIO is
active, it's slowered by one grade first. If that doesn't help,
PIO0 is forced. Note that this rule does not change transfer mode.
DMA is never degraded into PIO by this rule.
* If there have been more than ten ATA bus, timeout, HSM violation or
unclassified device errors for known supported commands && speeding
down DMA mode didn't help, the device is forced into PIO mode. Note
that this rule is considered only for PATA devices and is pretty
difficult to trigger.
One error can only trigger one rule at a time. After a rule is
triggered, error history is cleared such that the next speed down
happens only after some number of errors are accumulated. This makes
sense because now speed down is done in bigger stride.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Move forcing device to PIO0 on device disable into
ata_dev_disable(). This makes both old and new EHs act the same
way.
* Speed down only PIO mode on probe failure. All commands used during
probing are PIO commands. There's no point in speeding down DMA.
* Retry at least once after -ENODEV. Some devices report garbled
IDENTIFY data after certain events. This shouldn't cause device
detach and re-attach.
* Rearrange EH failure path for simplicity.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_down_xfermask_limit() accept @sel instead of @force_pio0.
@sel selects how the xfermask limit will be adjusted. The following
selectors are defined.
* ATA_DNXFER_PIO : only speed down PIO
* ATA_DNXFER_DMA : only speed down DMA, don't cause transfer mode change
* ATA_DNXFER_40C : apply 40c cable limit
* ATA_DNXFER_FORCE_PIO : force PIO
* ATA_DNXFER_FORCE_PIO0 : force PIO0 (same as original with @force_pio0 == 1)
* ATA_DNXFER_ANY : same as original with @force_pio0 == 0
Currently, only ANY and FORCE_PIO0 are used to maintain the original
behavior. Other selectors will be used later to improve EH speed down
sequence.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata used two separate sets of variables to record request size and
current offset for ATA and ATAPI. This is confusing and fragile.
This patch replaces qc->nsect/cursect with qc->nbytes/curbytes and
kills them. Also, ata_pio_sector() is updated to use bytes for
qc->cursg_ofs instead of sectors. The field used to be used in bytes
for ATAPI and in sectors for ATA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_eh_suspend() was returning 0 regardless of failure. This bug has
potential to lose data on suspend. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata EH ignores port-wide actions in per-dev action mask. However,
device resume requests EH_SOFTRESET using per-dev action mask. Under
certain circumstances, this results in not resetting frozen port after
resuming which causes failure of all commands.
This patch allows port-wide actions to be requested in per-dev action
mask. Before EH recovery starts, port-wide actions will be collected.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
libata switched to IRQ-driven IDENTIFY when IRQ-driven PIO was
introduced. This has caused a lot of problems including device
misdetection and phantom device.
ATA_FLAG_DETECT_POLLING was added recently to selectively use polling
IDENTIFY on problemetic drivers but many controllers and devices are
affected by this problem and trying to adding ATA_FLAG_DETECT_POLLING
for each such case is diffcult and not very rewarding.
This patch makes libata always use polling IDENTIFY. This is
consistent with libata's original behavior and drivers/ide's behavior.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If EH command is issued to a frozen port, it fails with AC_ERR_SYSTEM.
libata used to request sense even when the port is frozen needlessly
adding AC_ERR_SYSTEM to err_mask. Don't do it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Improve failed qc reporting. The original message didn't include the
actual command nor full error status and it was necessary to
temporarily patch the code to find out exactly which command is
causing problem. This patch makes EH report full command and result
TFs along with data direction and length. This change will make bug
reports more useful.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some controllers (ICHs in piix mode), there is *NO* reliable way to
determine device presence other than issuing IDENTIFY and see how the
transaction proceeds by watching the TF status register.
libata acted this way before irq-pio and phantom devices caused very
little problem but now that IDENTIFY is performed using IRQ drive PIO,
such phantom devices now result in multiple 30sec timeouts during
boot.
This patch implements ATA_FLAG_DETECT_POLLING. If a LLD sets this
flag, libata core issues the initial IDENTIFY in polling mode and if
the initial data transfer fails w/ HSM violation, the port is
considered to be empty thus replicating the old libata and IDE
behavior.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_dev_read_id() take @flags instead of @post_reset. Currently
there is only one flag defined - ATA_READID_POSTRESET, which is
equivalent to @post_reset. This is preparation for polling presence
detection.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata EH used to perform ata_set_mode() iff the EH session performed
reset as indicated by ATA_EHI_DID_RESET. This is incorrect because
->dev_config() called by revalidation is allowed to modify transfer
mode which ata_set_mode() should take care of. This patch implements
the following two flags.
* ATA_EHI_SETMODE: set during EH to schedule ata_set_mode(). Both new
device attachment and revalidation set this flag.
* ATA_EHI_POST_SETMODE: set while the device is revalidated after
ata_set_mode(). Post-setmode revalidation is different from initial
configuaration and EH revalidation in that ->dev_config() is not
allowed tune transfer mode. LLD can use this flag to determine
whether it's allowed to tune transfer mode. Note that POST_SETMODE
->dev_config() is guaranteed to be preceded by non-POST_SETMODE
->dev_config().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ehi flag ATA_EHI_PRINTINFO. This flag is set when device
configuration needs to print out device info. This used to be handled
by @print_info argument to ata_dev_configure() but LLDs also need to
know about it in ->dev_config() callback.
This patch replaces @print_info w/ ATA_EHI_PRINTINFO and make sata_sil
print workaround messages only on the initial configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate delayable work items from non-delayable work items be splitting them
into a separate structure (delayed_work), which incorporates a work_struct and
the timer_list removed from work_struct.
The work_struct struct is huge, and this limits it's usefulness. On a 64-bit
architecture it's nearly 100 bytes in size. This reduces that by half for the
non-delayable type of event.
Signed-Off-By: David Howells <dhowells@redhat.com>
This removes the layering violation where drivers have to fiddle
directly with EH flags. Instead we now recognize -ENOENT means "no port"
and do the handling in the core code.
This also removes an instance of a call to disable the port, and an
identical printk from each driver doing this. Even better - future rule
changes will be in one place only.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The biggest change is that ata_host_set is renamed to ata_host.
* ata_host_set => ata_host
* ata_probe_ent->host_flags => ata_probe_ent->port_flags
* ata_probe_ent->host_set_flags => ata_probe_ent->_host_flags
* ata_host_stats => ata_port_stats
* ata_port->host => ata_port->scsi_host
* ata_port->host_set => ata_port->host
* ata_port_info->host_flags => ata_port_info->flags
* ata_(.*)host_set(.*)\(\) => ata_\1host\2()
The leading underscore in ata_probe_ent->_host_flags is to avoid
reusing ->host_flags for different purpose. Currently, the only user
of the field is libata-bmdma.c and probe_ent itself is scheduled to be
removed.
ata_port->host is reused for different purpose but this field is used
inside libata core proper and of different type.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
