Presently shm_align_mask is only looked at for the bottom up case, but we
still want this for proper colouring constraints in the topdown case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There still seems to be some stack corruption to sort out here, so flag
this as BROKEN until this issue is sorted out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The old arch/sh/kernel/timers/ directly will be going away completely
once the rest of the TMU users are migrated, so move the dummy broadcast
driver up a level in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the stragglers (MTU2/CMT/etc.) have been rewritten and we are
selecting both GENERIC_TIME and GENERIC_CLOCKEVENTS, the get_offset()
timer op is completely unused. As a result, we are now able to kill off
the ARCH_USES_GETTIMEOFFSET references.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the rest of the timers that didn't support clockevents have been
rewritten, both of these can be enabled by default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the SH timers use a roughly identical structure for platform data,
which presently is broken out for each block. Consolidate all of these
definitions, as there is no reason for them to be broken out in the first
place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7722. Only clockevent
mode is enabled for now, clocksource requires this patch:
"clocksource: setup mult_orig in clocksource_enable()"
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a TMU driver for the SuperH architecture.
The TMU driver is a platform driver with early platform
support to allow using a TMU channel as clockevent or
clocksource during system bootup or later.
Clocksource or clockevent can be selected.
Both periodic and oneshot clockevents are supported.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old MTU2 driver (CONFIG_SH_MTU2/timer-mtu2.c)
As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_MTU2
and configure timer channel using platform data.
If multiple MTU channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_mtu2.0" to select the first channel.
To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MTU2 platform data for the following cpus:
- sh7201 (3/5 channels)
- sh7203/sh7263 (2/4 channels)
- sh7206 (3/5 channels)
- MXG (3/5 channels)
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a MTU2 driver for the SuperH architecture.
The MTU2 driver is a platform driver with early platform
support to allow using a MTU2 channel as only clockevent
during system bootup.
Clocksource on sh2a is currently unsupported due to code
generation issues with 64-bit math, so at this point only
periodic clockevent support is in place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert sh to use GENERIC_TIME via the arch_getoffset() infrastructure.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: cleanup
convert the last remaining users to no_irq_chip
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old CMT driver (CONFIG_SH_CMT/timer-cmt.c)
As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_CMT
and configure timer channel using platform data.
If multiple CMT channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_cmt.0" to select the first channel.
To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds 16-bit cmt platform data for the following cpus:
- sh7619 (2 channels)
- sh7203/sh7263 (2 channels)
- sh7206 (2 channels)
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All 32-bit SuperH processors currently go through __ioremap_mode()
and check for IO_TRAPPED and directly mapped segments. With this
patch we simplify the MMU less case with a pass through version of
__ioremap_mode() which just returns the physical address.
The effects of this is change are:
- fix non-MMU ioremap() of high address hardware blocks (sh7203 CMT)
- make sure IO_TRAPPED is not selected
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The device registration was accidentally omitted, add it back in. Do some
basic device probing as well, so this doesn't show up for platforms that
tie in to the RTC interface properly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves the SuperH timer setup code from time_init()
to late_time_init(). Good things about this change:
- interrupts: they are enabled at late_time_init()
- mm: regular kmalloc() can be used at late_time_init()
Together with moving to late_time_init() this patch changes
the sh_cmt driver to always allocate with kmalloc(). This
simplifies the code a bit and also fixes section mismatches.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh architecture has some code in the .text.init section, but it
does not reference that section in its linker scripts.
This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTS7751R2D_1 boards only support 1MB of socket-mounted MBM29F040
flash, which we just leave alone as it's not terribly interesting.
This adds support for the s29gl256p on the r2d+ boards that makes a bit
more sense to expose to the user.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
syscall_nr is presently defined as unsigned in the SH-5 pt_regs,
while the syscall restarting code wants it to be signed. Fix this
up, and bring it in line with the other SH parts.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the problem that cannot work 29-bit mode when use sh7785lcr_defconfig.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This has the consequence of changing the section name use for head
code from ".text.head" to ".head.text". Since this commit changes all
users in the architecture, this change should be harmless.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mmap2 uses a fixed page shift of 12, regardless of the PAGE_SIZE setting.
Fix up the mmap2 code to add some sanity checks on the mapping, and to
update pgoff accordingly.
Error handling bits based on 4280e3126f
("frv: fix mmap2 error handling").
Signed-off-by: Toshinobu Sugioka <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the pci-auto cruft is gone, pci-lib can go away.
Roll it back in to pci-new.c where it originally split off from.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The se7751 was still doing the PCI fixups in its own board directory,
so we move it over to arch/sh/drivers/pci/ with the rest of the board
fixups. It has bitrotted significantly over the years, so will still
likely need a bit of work to bring back up to date.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the similar sort of scheme that the refactored SH7780 code
uses, using a 64MB CS3 mapping to handle the window0 case, and simply
discarding window1. This vastly simplifies the code, and allows most of
the board-specific setup to go die.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These fixups seem to have bitrotted a bit since their introduction in the
2.4 days. As we never had much use for them in the first place, and
nothing is using them any more, kill them off the rest of the way.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This isn't a real BAR, so prevent any attempts to move it, as we don't
wish to encourage a bus luck by overzealous PCI initialization code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
