Correctly work around T3A issues by checking "hwtype != T3A" instead of
"hwtype == T3B". This will be needed for new hardware types.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The existing logic incorrectly maps this buffer list:
0: addr 0x10001000, size 0x1000
1: addr 0x10002000, size 0x1000
To this bogus page list:
0: 0x10000000
1: 0x10002000
The shift calculation must also take into account the address of the
first entry masked by the page_mask as well as the last address+size
rounded up to the next page size.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- for kernel mode cqs, call event notification handler when flushing.
- flush QP when moving from RTS -> CLOSING.
- fix logic to identify a kernel mode qp.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the increment of s_hdrwords into the existing if block that tests
if we're doing a send with immediate, to save one test of the opcode.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
qdisc_run() now tests for queue_stopped() before calling
__qdisc_run(), and the same check is done in every iteration of
__qdisc_run(), so another check is not required in the driver xmit.
This means that ipoib_start_xmit() no longer needs to test
netif_queue_stopped(); the test was added to fix earlier kernels,
where the networking stack did not guarantee that the xmit method of
an LLTX driver would not be called after the queue was stopped, but
current kernels do provide this guarantee.
To validate, I put a debug in the TX_BUSY path which never hit with 64
threads running overnight exercising this code a few 100 million
times.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new mappings from port physical state (a HW register value) to the
IB SubnGet(PortInfo) port physical state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBA7220 uses a count-based triggering mechanism, and therefore
can't use the same bandwidth verification mechanism as older chips.
To support the 7220, allow enabling and disabling armlaunch errors on
application request. Minor robustness improvements as well.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up some unused header fields, minor related cleanup.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IBA7220 includes many more configurable IB settings. Getting/setting
these is now grouped into a pair of chip specific functions accessed via
function pointers. Provide sysfs access to these settings.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This adds the new (sometimes empty) chip-specific functions to the older
chips, and makes the initialization and related functions consistent across
all 3 chips.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This code has been unused for some time, but still had leftovers
from when it was used.
Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some HW revisions of eHCA2 may cause an RC connection to break if they
received RDMA Reads over that connection before. This can be
prevented by assuring that, after the first RDMA Read, the QP receives
a new RDMA Read every few million link packets.
Include code into the driver that inserts an empty (size 0) RDMA Read
into the message stream every now and then if the consumer doesn't
post them frequently enough.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch enhances ehca with a capability to "autodetect" the ports
being connected physically. In order to utilize that function the
module option nr_ports must be set to -1 (default is 2 - two
ports). This feature is experimental and will made the default later.
More detail:
If the user connects only one port to the switch, current code requires
1) port one to be connected and
2) module option nr_ports=1 to be given.
If autodetect is enabled, ehca will not wait at creation of the GSI QP
for the respective port to become active. Since firmware does not
accept modify_qp() while the port is down at initialization, we need
to cache all calls to modify_qp() for the SMI/GSI QP and just return a
good return code.
When a port is activated and we get a PORT_ACTIVE event, we replay the
cached modify-qp() parms and re-trigger any posted recv WRs. Only then
do we forward the PORT_ACTIVE event to registered clients.
The result of this autodetect patch is that all ports will be
accessible by the users. Depending on their respective cabling only
those ports that are connected properly will become operable. If a
user tries to modify a regular QP of a non-connected port, modify_qp()
will fail. Furthermore, ibv_devinfo should show the port state
accordingly.
Note that this patch primarily improves the loading behaviour of
ehca. If the cable is removed while the driver is operating and
plugged in again, firmware will handle that properly by sending an
appropriate async event.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a .change_queue_depth handler to the scsi_host_template in the
iSER driver. iscsi_change_queue_depth was added to iscsi_tcp in order
to solve the problem of queue depth which was too high for some
targets. It is also applicable for iSER.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some RDMA CM events are not supported or not handled in iSER.
This patch adds some info (printk) for the user about them.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a FMR is released via ib_fmr_pool_unmap(), the FMR usually ends
up on the free_list rather than the dirty_list (because we allow a
certain number of remappings before actually requiring a flush).
However, ib_fmr_batch_release() only looks at dirty_list when flushing
out old mappings. This means that when ib_fmr_pool_flush() is used to
force a flush of the FMR pool, some dirty FMRs that have not reached
their maximum remap count will not actually be flushed.
Fix this by flushing all FMRs that have been used at least once in
ib_fmr_batch_release().
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Normally, the serial numbers for flush requests and flushes executed
for an FMR pool should be in sync.
However, if the FMR pool flushes dirty FMRs because the
dirty_watermark was reached, we wake up the cleanup thread and let it
do its stuff. As a side effect, the cleanup thread increments
pool->flush_ser, which leaves it one higher than pool->req_ser. The
next time the user calls ib_flush_fmr_pool(), the cleanup thread will
be woken up, but ib_flush_fmr_pool() won't wait for the flush to
complete because flush_ser is already past req_ser. This means the
FMRs that the user expects to be flushed may not have all been flushed
when the function returns.
Fix this by telling the cleanup thread to do work exclusively by
incrementing req_ser, and by moving the comparison of dirty_len and
dirty_watermark into ib_fmr_pool_unmap().
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
In addition to being overly complex, the locking in user_mad.c is
broken: there were multiple reports of deadlocks and lockdep warnings.
In particular it seems that a single thread may end up trying to take
the same rwsem for reading more than once, which is explicitly
forbidden in the comments in <linux/rwsem.h>.
To solve this, we change the locking to use plain mutexes instead of
rwsems. There is one mutex per open file, which protects the contents
of the struct ib_umad_file, including the array of agents and list of
queued packets; and there is one mutex per struct ib_umad_port, which
protects the contents, including the list of open files. We never
hold the file mutex across calls to functions like ib_unregister_mad_agent(),
which can call back into other ib_umad code to queue a packet, and we
always hold the port mutex as long as we need to make sure that a
device is not hot-unplugged from under us.
This even makes things nicer for users of the -rt patch, since we
remove calls to downgrade_write() (which is not implemented in -rt).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are a few places in the ipath driver where a variable is
re-declared within a block where it is already in scope. Most of these
extra declarations can simply be removed, since the variable from the
outer scope is used in a way so that it does not need to keep its
variable across the block with the re-declaration.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use round_jiffies() to align ehca's 1-second timer with other timers
and potentially save power by sleeping cores for longer.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
By default, the responder_resources parameter is set to that received
in a connection request. The passive side may override this value
when accepting the connection. Use the value provided by the passive
side when transitioning the QP to RTR state, rather than the value
given in the connect request. Without this change, the RTR transition
may fail if the passive side supports fewer responder_resources than
that in the request.
For code consistency and to protect against QP destruction, restructure
overriding initiator_depth to match how responder_resources is set.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The original QHT7040 had significant performance issues so there was an
additional check in the driver for a newer serial number. Support for
the small quantities of that board shipped has been dropped, so this
patch removes the special checks to simplify the code.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different chips have different width interrupt status registers, so add
a flag and accessor function to decide which width register read to use.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 6110 had a bug that caused some registers to be swapped; it was
fixed for the 7220 (and didn't affect the 6120 because it had fewer
registers). This adds a flag and related code to handle that, and
includes some minor cleanups in the same area.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
The number of configured ports for the 7220 changes the number of eager
TIDs available per port, for all but port 0 (kernel port) which remains
constant, so add a field to give port0 count separate from the portdata
structure.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
User registers have different alignments on different chips (4KB on
older, 64KB on 7220). Allow mapping the user registers on kernels with
page sizes up to 64K.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Various hardware counters are exported via the ipath file system (since
it is binary data). The old file format was very dependent on the HW
offsets for these registers. Newer HCA chips can have different
counters at different offsets. This patch adds a level of indirection
to make the file format consistent across HCAs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for QLogic HCAs which have hardware performance sampling
registers for PortSamplesControl and PortSamplesResult MADs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When you have multiple targets, it gets really confusing when you try
to track down who did a reset when there is no identifying information
in the log message, especially when the same extension ID is mapped
through two different local IB ports. So, add an identifier that can
be used to track back to which local IB port/remote target pair is the
one having problems.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Acked-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some HCAs (such as ehca2) support SRQ, but only support fewer than 16 SG
entries for SRQs. Currently IPoIB/CM implicitly assumes all HCAs will
support 16 SG entries for SRQs (to handle a 64K MTU with 4K pages). This
patch removes that restriction by limiting the maximum MTU in connected
mode to what the maximum number of SRQ SG entries allows.
This patch addresses <https://bugs.openfabrics.org/show_bug.cgi?id=728>
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
By default, the SCSI mid-layer seems to send down 512KB requests
(sg_tablesize = 256), with some requests occasionally combined. By
allowing the mid-layer to chain requests, we can easily grow to 1024KB
or larger -- I've tested 4096KB I/O requests with no problems.
I looked through the DMA paths on the hardware drivers to ensure they
could take advantage of the SG chaining, and it seems that every one
except ipath uses the system's DMA routines, which have been converted
to handle chaining. ipath looks like it should be OK, but I have no
way to test it.
Signed-off-by: David Dillow <dillowda@ornl.gov>
[ Tested on ipath. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current SRP initiator will send requests even if it has no credits
available. The results of sending extra requests are vendor specific,
but on some devices, overrunning credits will cost 85% of peak
performance -- e.g. 100 MB/s vs 720 MB/s. Other devices may just drop
the requests.
This patch will tell the SCSI midlayer to queue requests if there are
fewer than two credits remaining, and will not issue a task management
request if there are no credits remaining. The mid-layer will retry
the queued command once an outstanding command completes.
The patch also removes the unlikely() in __srp_get_tx_iu(), as it is
not at all unlikely to hit this limit under heavy load.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs. The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised. This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.
The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch moves some arrays that were defined per-device to be
variables defined in the per context data structure, thus avoiding extra
kzalloc() calls.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In preparation for upcoming chips that have different values for
INFINIPATH_R_PORTENABLE_SHIFT, INFINIPATH_R_INTRAVAIL_SHIFT,
INFINIPATH_R_TAILUPD_SHIFT, and portcfg_shift, remove the shared
#defines and use device-specific variables instead.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
kreceive is now portdata * instead of devdata * and other kreceive
related cleanups....
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove an unused parameter and fix up the comment.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a couple of minor problems with RNR NAK handling:
- The insertion sort was causing extra delay when inserting ahead
vs. behind an existing entry on the list.
- A resend of a first packet of a message which is still not ready,
needs another RNR NAK (i.e., it was suppressed when it shouldn't).
- Also, the resend tasklet doesn't need to be woken up unless the
ACK/NAK actually indicates progress has been made.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows ehca to forward event client-reregister-required to
registered clients. One such event is generated by a switch eg. after
its reboot.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than byte-swapping cqe->g_mlpath_rqpn each time we extract a
field from it, byte-swap it once into a temporary variable. This
results in smaller, better code -- eg, on 32-bit x86:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5 (-5)
function old new delta
mlx4_ib_poll_cq 1188 1183 -5
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove MSI support from the mthca driver, as scheduled. There is no
reason to use MSI instead of MSI-X, since MSI-X performs better. No
one has spoken up since MSI support was deprecated in commit f6be6fbe
("IB/mthca: Schedule MSI support for removal"), so apparently the MSI
support is unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
