The StMicro NAND chip (512Mbit, 64MB) is connected to the local bus,
the first local bus' user-programmable machine is configured by the
firmware to work with NAND chips.
QE GPIO pin is used to poll the NAND's Ready-Not-Busy signal.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This patch adds support for the registers held in the devices main FPGA,
exposing extra information about the revision of the board through cpuinfo.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale Elo DMA driver binds to all DMA channels in the device tree that
are compatible with "fsl,eloplus-dma-channel". This conflicts with the sound
drivers for the MPC8610 HPCD. On this board, the SSI uses two DMA channels and
therefore those channels are not available for general purpose use. We
change the compatible properties for these channels "fsl,ssi-dma-channel".
This works because the sound drivers don't actually check the compatible
property when it grabs channels.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT3 interrupt line.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Uses mpc83xx_add_bridge in fsl_pci.c
Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).
A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale
MPC8610 HPCD device tree. These properties connect the SSI nodes to the
DMA nodes for the DMA channels that the SSI should use. Also update the
ssi.txt documentation.
These properties will be needed when the ASoC V2 version of the Freescale
MPC8610 device drivers are merged into the mainline.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For Freescale 8xxx devices that use an MPIC, the interrupt numbers in
the device tree must be 16 greater than the values documented in the
reference manual. In these chips, the MPIC is wired to use the first
16 numbers for external interrupts, but the documentation numbers
internal interrupts from 0.
In the MPC8610 HPCD device tree, the interrupt properties for the DMA
channels for DMA2 were not the adjusted values. This fixes that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC610, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the localbus node, moves the bcsr node into the
localbus node, and adds the flash node.
Also enable MTD support in the defconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the AD7414 temperature sensor
on Sequoia PPC440EPx board.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the Yosemite board to the explicitly supported list for ppc44x_simple
boards and remove the compatible entry for bamboo from the DTS file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add explicit support for the AMCC Glacier eval board to Kconfig and the
ppc44x_simple file. Also removes the cayonlands compatible entry from the
DTS file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Due to the missing compatible property for the SOC, the MPC I2C buses are
not found any more. This patch fixes this issue. Furthermore it corrects
the name of the SOC node and adds the missing I2C node for the RTC.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we coverted the .dts to v1 we lost a space between the irq
and its polarity/sense information. This causes a bit of chaos
as the reset of the blob is off by one cell.
This was noticed by booting and getting errors w/ATA due to
lock of interrupts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Remove include/linux/harrier_defs.h
powerpc: Do not ignore arch/powerpc/include
powerpc: Delete completed "ppc removal" task from feature removal file
powerpc/mm: Fix attribute confusion with htab_bolt_mapping()
powerpc/pci: Don't keep ISA memory hole resources in the tree
powerpc: Zero fill the return values of rtas argument buffer
powerpc/4xx: Update defconfig files for 2.6.27-rc1
powerpc/44x: Incorrect NOR offset in Warp DTS
powerpc/44x: Warp DTS changes for board updates
powerpc/4xx: Cleanup Warp for i2c driver changes.
powerpc/44x: Adjust warp-nand resource end address
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FPGA offset in NOR flash was converted incorrectly when switching from
64M to 4M flash.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added support for the new at24 eeprom driver.
Documented a new fpga section, the DMA scatter gather list.
Removed index from i2c. No longer needed.
Fixed the leds section.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.
i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc7448hpc2 board doesn't have an alias block like
most of the other modern eval boards have. We need this
block in order to have u-boot be able to make use of the
CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node)
in the future.
Also remove the old, redundant chosen node. Of all the modern
Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only
one which still has it. Its presence also breaks with some older
versions of u-boot, like 1.3.1 -- which try and insert a
second chosen node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use
PCI sideband interrupt that is specified in the device tree.
Current HPCD's device tree specify that IDE interrupt is low to high
sensitive, but in practice ULi IDE throws active-high interrupts (not
active-low as all normal PCI devices).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename MPIC label to mpic to match all other 85xx .dts and to fix compile
issue introduced by addition of the DMA node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current device tree is only bare bones. This patch adds nodes to make
it a complete tree for the MPC5121ads.
Added nodes include:
mbx - opengl coprocessor
nfc - nand flash controller
cpld-pic - on board cpld
rtc
clock - clock control
pmc - power management control
gpio
mscan - can module
i2c
axe - audio coprocessor
display - display interface unit
mdio
ethernet
usb
ioctl - pin config
pata
ac97 - PSC configured as AC97
pscfifo - psc fifo configuration
dma
pci
Fix typo in header changing MDS to ADS.
Add a compatible property of the form "fsl,mpc5121-..."
to nodes missing one.
Changed localbus compatible to fsl,mpc5121-localbus, this does
not break anything because the only code that uses it finds it
via the node name, not compatible.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the still missing FDT nodes for the MSCAN devices for
the TQM52xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Various instances of the EMAC core have varying: 1) number of address
match slots, 2) width of the registers for handling address match slots,
3) number of registers for handling address match slots and 4) base
offset for those registers.
As the driver stands today, it assumes that all EMACs have 4 IAHT and
GAHT 32-bit registers, starting at offset 0x30 from the register base,
with only 16-bits of each used for a total of 64 match slots.
The 405EX(r) and 460EX now use the EMAC4SYNC core rather than the EMAC4
core. This core has 8 IAHT and GAHT registers, starting at offset 0x80
from the register base, with ALL 32-bits of each used for a total of
256 match slots.
This adds a new compatible device tree entry "emac4sync" and a new,
related feature flag "EMAC_FTR_EMAC4SYNC" along with a series of macros
and inlines which supply the appropriate parameterized value based on
the presence or absence of the EMAC4SYNC feature.
The code has further been reworked where appropriate to use those macros
and inlines.
In addition, the register size passed to ioremap is now taken from the
device tree:
c4 for EMAC4SYNC cores
74 for EMAC4 cores
70 for EMAC cores
rather than sizeof (emac_regs).
Finally, the device trees have been updated with the appropriate compatible
entries and resource sizes.
This has been tested on an AMCC Haleakala board such that: 1) inbound
ICMP requests to 'haleakala.local' via MDNS from both Mac OS X 10.4.11
and Ubuntu 8.04 systems as well as 2) outbound ICMP requests from
'haleakala.local' to those same systems in the '.local' domain via MDNS
now work.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This new file adds support for the ML507 reference design. The ML507
uses the Virtex 5 FXT FPGA which embeds a ppc440 core.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Added DMA nodes for the elo/elo-plus DMA engines.
Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
