Users reported that ARP's were lost with igb. The problem
is fixed by not enabling this manageability configuration
bit.
None of the release_manageability code is actually needed as the
normal device reset during a shutdown returns everthing to
the right condition automatically.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In reply to "RE: [Fwd: [PATCH 2.6.25] ixgbe/igb: correctly obtain protocol
information on transmit]" from Andy Gospodarek:
The driver was incorrectly looking at socket headers for
protocol information, needed for checksumming offload. Fix
this by not looking at the socket but frame headers instead.
This disregards extension headers but it's unclear that linux
generates those anyway.
Tested by Andy Gospodarek.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CRC stripping was only correctly enabled for packet split recieves
which is used when receiving jumbo frames. Correctly enable SECRC
also for normal buffer packet receives.
Tested by Andy Gospodarek and Johan Andersson, see bugzilla #9940.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
According to one of OOPSes reported by Jann softirq can break
while skb is prepared for netif_rx. The report isn't complete,
so the real reason of the later bug could be different, but
IMHO this locking break in ax_bump is unsafe and unnecessary.
Reported-and-tested-by: Jann Traschewski <jann@gmx.de>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Megahertz EM1144 PCMCIA ethernet adapter needs special handling
because it has two VERS_1 tuples and the station address is in
the second one. Conversion to generic handling of these fields
broke it. Reverting that fixes the device.
https://bugzilla.redhat.com/show_bug.cgi?id=233255
Thanks go to Jon Stanley for not giving up on this one until the
problem was found.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
[NET]: Make sure sockets implement splice_read
netconsole: avoid null pointer dereference at show_local_mac()
[IPV6]: Fix reversed local_df test in ip6_fragment
[XFRM]: Avoid bogus BUG() when throwing new policy away.
[AF_KEY]: Fix bug in spdadd
[NETFILTER] nf_conntrack_proto_tcp.c: Mistyped state corrected.
net: xfrm statistics depend on INET
[NETFILTER]: make secmark_tg_destroy() static
[INET]: Unexport inet_listen_wlock
[INET]: Unexport __inet_hash_connect
[NET]: Improve cache line coherency of ingress qdisc
[NET]: Fix race in dev_close(). (Bug 9750)
[IPSEC]: Fix bogus usage of u64 on input sequence number
[RTNETLINK]: Send a single notification on device state changes.
[NETLABLE]: Hide netlbl_unlabel_audit_addr6 under ifdef CONFIG_IPV6.
[NETLABEL]: Don't produce unused variables when IPv6 is off.
[NETLABEL]: Compilation for CONFIG_AUDIT=n case.
[GENETLINK]: Relax dances with genl_lock.
[NETLABEL]: Fix lookup logic of netlbl_domhsh_search_def.
[IPV6]: remove unused method declaration (net/ndisc.h).
...
This patch avoids a null pointer dereference when we read local_mac
for netconsole in configfs and shows default local mac address
value.
A null pointer dereference occurs when we call show_local_mac() via
local_mac entry in configfs before we setup the content of netpoll
using netpoll_setup().
Signed-off-by: Keiichi KII <k-keiichi@bx.jp.nec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_table_find (for FMR MPTs) requires that ICM memory already be
mapped. Before this fix, FMR allocation depended on ICM memory
already being mapped for the MPT entry. If all currently mapped
entries are taken, the find operation fails (even if the MPT ICM table
still had more entries, which were just not mapped yet).
This fix moves the mpt find operation to fmr_enable, to guarantee that
any required ICM memory mapping has already occurred.
Found by Oren Duer of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 313abe55 ("mlx4_core: For 64-bit systems, vmap() kernel queue
buffers") caused this to pop up on powerpc allyesconfig, looks like a
missing include file:
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:162: error: implicit declaration of function 'vmap'
drivers/net/mlx4/alloc.c:162: error: 'VM_MAP' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:162: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:162: error: for each function it appears in.)
drivers/net/mlx4/alloc.c:162: warning: assignment makes pointer from integer without a cast
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_free':
drivers/net/mlx4/alloc.c:187: error: implicit declaration of function 'vunmap'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It's easy to oversee this issue when working with this card
as evrything will work OK but performance is severely limited
(something like 1.5gbit on a x1 link) if the pci-express
slot does not offer more bandwidth.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A logic mishap caused the adapter to keep link while we can
disable it due to WoL not being active, and vice versa.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We're already starting to see reports from users still
using e1000 where they should be using e1000e now that this is
actually possible. Just to prevent some of this thrash, add
a big warning on load on these devices that people should
switch to e1000e.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool support to tsi108_eth network driver.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug fix for tsi108_eth network driver.
This patch fixes a problem with link recovery after connection was lost.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code clean-up for tsi108_eth network driver.
This patch removes not needed dummy read and the corresponding comment.
The PHY logic requires two reads from the status register to get
current link status. This is done correctly inside mii_check_media().
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug fix for tsi108_eth network driver.
This patch fixes a problem with detection of 1000Mb speed.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a use-after-free introduced by
commit a79d8e93d3 and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix following warnings:
WARNING: drivers/net/sis190.o(.text+0x103): Section mismatch in reference from the function sis190_get_mac_addr() to the function .devinit.text:sis190_get_mac_addr_from_apc()
WARNING: drivers/net/sis190.o(.text+0x10e): Section mismatch in reference from the function sis190_get_mac_addr() to the function .devinit.text:sis190_get_mac_addr_from_eeprom()
Annotate sis190_get_mac_addr() with __devinit.
Signed-off-by: Sergio Luis <sergio@uece.br>
sis190.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New chipsets introduced variant Rx FIFO sizes that need to be taken into
account when setting up the tx pause watermarks. This patch introduces
the new device feature flags based on a version and implements the new
watermarks.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch supports a new fix in hardware regarding tx collisions. In
the cases where we are in autoneg mode and the link partner is in forced
mode, we need to setup the tx deferral register differently in order to
reduce collisions on the wire.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When ARP completes due to a request rather than a reply the neighbor is
marked NUD_STALE instead of reachable (see arp_process()). The handler
for the resulting netevent needs to check also for NUD_STALE.
Failure to use the arp entry can cause RDMA connection failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Show whether the MAC address was read from the EEPROM or
the onboard PAR registers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading the ID register does not always return the correct ID
from the device, so we retry several times to see if we get
a correct value.
These failures seem to be excaserbated by the speed of the
access to the chip (possibly time between issuing the address
and then the data cycle).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add entry to handle the MII ioctl() calls via the
generic_mii_ioctl call.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the platform data to specify to the DM9000 driver
that there is no posibility of an attached EEPROM on the
device, so default all reads to 0xff and ignore any
write operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The writing of the data should implicitly truncate
the data to 8bits, so do not bother with the ands
in the code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the cal_CRC as this is basically wrappering the
ether_crc_le function, and is only being used by the
multicast hash table functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code was using a delay of 8ms, when it should have been
using the EEPROM status flag from the device to indicate the
EEPROM transaction had finished.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netif_msg_*() macros to enable the debugging based
on the board's msg_enable field. The output still goes via
the dev_dbg() macros, so will be tagged and output as
appropriate.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a perfectly good version control system, so we do not
need to duplicate change comments in the header for this code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure we hold the spinlock whilst the registers and being
modified even though we hold the overall lock. This should
protect against an interrupt happening whilst we are using
the device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the old hack to program an initial EEPROM setting
into the DM9000 as we now have ethtool support for reading
and writing the EEPROM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the msg_enable value to be read and written by
the ethtool interface.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool support to access the configuration EEPROM
connected to the DM9000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a mutex to serialise access to the chip functions from
entries such as the ethtool and the MII code. This should
reduce the amount of time the spinlock is held to protect
the address register.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The srom array in the board data is only being used in the device probe
routines. The probe also only uses the first 6 bytes of an array
we spend 512ms reading 128 bytes from. Change to reading the
MAC area directly to the MAC address structure.
As a side product, we rename the read_srom_word to dm9000_read_eeprom
to bring it into line with the rest of the driver. No change is made
to the delay in this function, which will be dealt with in a later
patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can use sleeping functions when reading and writing the
PHY registers, so let us sleep instead of busy waiting for
the PHY.
Note, this also fixes a bug reading the PHY where only 100uS
was being used instead of 150uS
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The phy read and write routines call udelay() with the board
lock held, and with the posibility of IRQs being disabled. Since
these delays can be up to 500usec, and are only required as we
have to save the chip's address register.
To improve the behaviour, hold the lock whilst we are writing
and then restore the state before the delay and then repeat
the process once the delay has happened.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the timer based MII phy polling, as this is
currently broken with the new EEPROM code that now
uses mutexes to protect the phy access.
This will need to be replaced in the future by some
form of mutex safe mechanism for reading the MII
phy status.
The replacement has not been done here as changing
this patch, which is early in the sequence has quite
a knock-on effect. Once this series is merged, then
a new presentation of an patch to poll the MII link
status can be added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the flags in the IRQ resource to specify the type of
IRQ being requested, so that systems which do not have
level-based interrupts, or change the interrupt in some
other way can specify this without making an #ifdef mess
in the driver.
This is specifically designed to undo the change in commit
4e4fc05a2b which hardwires the
type for everyone but blackfin to IRQT_RISING, which breaks
all a number of Simtec boards which use (and setup in the
bootloader) active low IRQs.
Note, although there where originally objections due to
the use of IORESOURCE_IRQ and IRQT_ flags not sharing the
same definition, at least <include/linux/interrupt.h> notes
these are the same.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CC: Daniel Mack <daniel@caiaq.de>
CC: Bryan Wu <bryan.wu@analog.com>
CC: Alex Landau <landau.alex@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the debug macros to use the compiler to elide any
unnecessary debug level, and to allow device configurable
debug control.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move to using dev_dbg() and friends for the output of
information to the user.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch adds a flag to the DM9000 platform data which, when set,
configures the device to use an external PHY.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linuy@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch splits the receive status in 8bit wide fields and convert the
packet length from little endian to CPU byte order.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Add common code for stopping queue.
2. No need to call netif_stop_queue followed by netif_wake_queue (and
infact a netif_start_queue could have been used instead), instead
call stop_queue if required, and remove code under USE_GTS macro.
3. There is no need to check for netif_queue_stopped, as the network
core guarantees that for us (I am sure every driver could remove
that check, eg e1000 - I have tested that path a few billion times
with about a few hundred thousand qstops but the condition never
hit even once).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The e1000 driver stores the content of the PCI resources into
unsigned long's before ioremapping. This breaks on 32 bits
platforms that support 64 bits MMIO resources such as ppc 44x.
This fixes it by removing those temporary variables and passing
directly the result of pci_resource_start/len to ioremap.
The side effect is that I removed the assignments to the netdev
fields mem_start, mem_end and base_addr, which are totally useless
for PCI devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
--
drivers/net/e1000/e1000_main.c | 18 +++++-------------
1 file changed, 5 insertions(+), 13 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for dual network (net_device) interface so that ethernet
and wireless can own separate ethX interfaces.
V2
- Fix the bug that bringing down and up the interface keeps rx
disabled.
- Make 'gelic_net_poll_controller()' extern , as David Woodhouse
pointed out at the previous submission.
- Fix weird usage of member names for the rx descriptor chain
V1
- Export functions which are convenient for both interfaces
- Move irq allocation/release code to driver probe/remove handlers
because interfaces share interrupts.
- Allocate skbs by using dev_alloc_skb() instead of netdev_alloc_skb()
as the interfaces share the hardware rx queue.
- Add gelic_port struct in order to abstract dual interface handling
- Change handlers for hardware queues so that they can handle dual
{source,destination} interfaces.
- Use new NAPI functions
This is a prerequisite for the new PS3 wireless support.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for interrupt driven port link status detection.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some ethtool handlers, which duplicate functionality that was already
provided by the common ethtool handlers.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code cleanup:
- Use appropriate prefixes for names instead of fixed 'gelic_net'
so that objects of the functions, variables and constants can be estimated.
- Remove definitions for IPSec offload to the gelic hardware. This
functionality is never supported on PS3.
- Group constants with enum.
- Use bitwise constants for interrupt status, instead of bit numbers to
eliminate shift operations.
- Style fixes.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark the members of the structure for DMA descriptors with proper endian
annotations and use the appropriate accessor macros.
As the gelic driver works only on PS3, all these macros will be
expanded to null.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The device id for lv1_net_set_interrupt_status_indicator() is wrong.
This path would be invoked only in the case of an initialization failure.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updates the 8139too driver to work with recently added
(a724605cb7) declared coherent memory
patch for the Dreamcast.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To kill the volatiles also switch it to stop poking ISA memory directly
without going through readb and friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change hard coded 2 to NET_IP_ALIGN. Added new #define with comments.
Tested amd_64
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
gcc-3.4.4 on powerpc:
drivers/net/starfire.c:219: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/via-velocity.c:443: error: chip_info_table causes a section type conflict
on this one I had to remove the __devinitdata too. Don't know why.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/natsemi.c:245: error: natsemi_pci_info causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/typhoon.c:137: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/pppol2tp.c: In function `pppol2tp_seq_tunnel_show':
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 4)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 5)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 6)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 7)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 8)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 9)
drivers/net/pppol2tp.c: In function `pppol2tp_seq_session_show':
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 5)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 6)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 7)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 8)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 9)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 10)
Not all platforms implement u64 with unsigned long long. eg: powerpc.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/bnx2.c:67: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/bnx2x.c:73: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Remove unused struct ib_device.flags member
IB/core: Add IP checksum offload support
IPoIB: Add send gather support
IPoIB: Add high DMA feature flag
IB/mlx4: Use multiple WQ blocks to post smaller send WQEs
mlx4_core: Clean up struct mlx4_buf
mlx4_core: For 64-bit systems, vmap() kernel queue buffers
IB/mlx4: Consolidate code to get an entry from a struct mlx4_buf
x25_asy does not take an ldisc reference before calling the flush method.
Fix it to use the helper function we provide.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'cris' of git://www.jni.nu/cris: (158 commits)
CRIS v32: Remove hwregs/timer_defs.h, it is now architecture specific.
CRIS v32: Change drivers/i2c.c locking.
CRIS v32: Rewrite ARTPEC-3 gpio driver to avoid volatiles and general cleanup.
CRIS: Add new timerfd syscall entries.
MAINTAINERS: Add my information for the CRIS port.
CRIS v32: Correct spelling of bandwidth in function name.
CRIS v32: Clean up nandflash.c for ARTPEC-3 and ETRAX FS.
CRIS v10: Cleanup of drivers/gpio.c
CRIS v10: drivers/net/cris/eth_v10.c rename LED defines to CRIS_LED to avoid name clash.
CRIS: Make io_pwm_set_period members unsigned in etraxgpio.h
CRIS: Move ETRAX_AXISFLASHMAP to common Kconfig file.
CRIS: Drop regs parameter from call to profile_tick in kernel/time.c
CRIS v32: Fix minor formatting issue in mach-a3/io.c
CRIS v32: Initialize GIO even if we're rambooting in kernel/head.S
CRIS v32: Remove kernel/arbiter.c, it now exists in machine dependent directory.
CRIS v32: Minor changes to avoid errors in asm-cris/arch-v32/hwregs/reg_rdwr.h
CRIS v32: arch-v32/hwregs/intr_vect_defs.h moved to machine dependent directory.
CRIS v32: Correct offset for TASK_pid in asm-cris/arch-v32/offset.h
CRIS v32: Move register map header to machine dependent directory.
CRIS v32: Let compiler know that memory is clobbered after a break op.
...
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add HP Jornada 6xx driver
leds: Remove the now uneeded ixp4xx driver
leds: Add power LED to the wrap driver
leds: Fix led-gpio active_low default brightness
leds: hw acceleration for Clevo mail LED driver
leds: Add support for hardware accelerated LED flashing
leds: Standardise LED naming scheme
leds: Add clevo notebook LED driver
As discussed on LKML some notion of 'function' is needed in
LED naming. This patch adds this to the documentation and
standardises existing LED drivers.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Now that struct mlx4_buf.u is a struct instead of a union because of
the vmap() changes, there's no point in having a struct at all. So
move .direct and .page_list directly into struct mlx4_buf and get rid
of a bunch of unnecessary ".u"s.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since kernel virtual memory is not a problem on 64-bit systems, there
is no reason to use our own 2-layer page mapping scheme for large
kernel queue buffers on such systems. Instead, map the page list to a
single virtually contiguous buffer with vmap(), so that can we access
buffer memory via direct indexing.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I got the following oops during interface ifup. Unfortunately its not
easily reproducable so I cant say for sure that my fix fixes this
problem, but I am confident and I think its correct anyway:
<2>kernel BUG at /space/kvm/drivers/virtio/virtio_ring.c:234!
<4>illegal operation: 0001 [#1] PREEMPT SMP
<4>Modules linked in:
<4>CPU: 0 Not tainted 2.6.24zlive-guest-07293-gf1ca151-dirty #91
<4>Process swapper (pid: 0, task: 0000000000800938, ksp: 000000000084ddb8)
<4>Krnl PSW : 0404300180000000 0000000000466374 (vring_disable_cb+0x30/0x34)
<4> R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:3 PM:0 EA:3
<4>Krnl GPRS: 0000000000000001 0000000000000001 0000000010003800 0000000000466344
<4> 000000000e980900 00000000008848b0 000000000084e748 0000000000000000
<4> 000000000087b300 0000000000001237 0000000000001237 000000000f85bdd8
<4> 000000000e980920 00000000001137c0 0000000000464754 000000000f85bdd8
<4>Krnl Code: 0000000000466368: e3b0b0700004 lg %r11,112(%r11)
<4> 000000000046636e: 07fe bcr 15,%r14
<4> 0000000000466370: a7f40001 brc 15,466372
<4> >0000000000466374: a7f4fff6 brc 15,466360
<4> 0000000000466378: eb7ff0500024 stmg %r7,%r15,80(%r15)
<4> 000000000046637e: a7f13e00 tmll %r15,15872
<4> 0000000000466382: b90400ef lgr %r14,%r15
<4> 0000000000466386: a7840001 brc 8,466388
<4>Call Trace:
<4>([<000201500f85c000>] 0x201500f85c000)
<4> [<0000000000466556>] vring_interrupt+0x72/0x88
<4> [<00000000004801a0>] kvm_extint_handler+0x34/0x44
<4> [<000000000010d22c>] do_extint+0xbc/0xf8
<4> [<0000000000113f98>] ext_no_vtime+0x16/0x1a
<4> [<000000000010a182>] cpu_idle+0x216/0x238
<4>([<000000000010a162>] cpu_idle+0x1f6/0x238)
<4> [<0000000000568656>] rest_init+0xaa/0xb8
<4> [<000000000084ee2c>] start_kernel+0x3fc/0x490
<4> [<0000000000100020>] _stext+0x20/0x80
<4>
<4> <0>Kernel panic - not syncing: Fatal exception in interrupt
<4>
After looking at the code and the dump I think the following scenario
happened: Ifup was running on cpu2 and the interrupt arrived on cpu0.
Now virtnet_open on cpu 2 managed to execute napi_enable and disable_cb
but did not execute rx_schedule. Meanwhile on cpu 0 skb_recv_done was
called by vring_interrupt, executed netif_rx_schedule_prep, which
succeeded and therefore called disable_cb. This triggered the BUG_ON,
as interrupts were already disabled by cpu 2.
I think the proper solution is to make the call to disable_cb depend on
the atomic update of NAPI_STATE_SCHED by using netif_rx_schedule_prep
in the same way as skb_recv_done.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PHY Lib now uses mutexes instead of spin_locks. ucc_geth
and gianfar both grab the locks in their mdio_reset functions,
so they need to use mutex_(un)lock instead. This was not caught
until someone tested it on an SMP system.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various registers need to be preserved before resetting the device.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver needs to ack only the phy status bits that it is currently
handling and preserve the other bits for the other handlers. For
example, when reading/writing from the phy, it should not clear the link
change interrupt bit. This will cause a missing link change interrupt.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the issue where the transmitter and receiver must be
restarted when applying new changes to certain registers.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts cpmac to the new Fixed PHY infrastructure, though it
doesn't fix all the problems with that driver. I didn't even bother to
test this patch to compile, because cpmac driver is broken in several ways:
1. This driver won't compile by itself because lack of its header describing
platform data;
2. It assumes that fixed PHYs should be created by the ethernet driver.
It is wrong assumption: fixed PHYs creation is platform code authority,
driver must blindly accept bus_id and phy_id platform data variables
instead.
Also, it seem that that driver doesn't have actual in-tree users, so
nothing to fix further.
The main purpose of that patch is to get rid of the following Kconfig
warning:
scripts/kconfig/conf -s arch/powerpc/Kconfig
drivers/net/Kconfig:1713:warning: 'select' used by config symbol
'CPMAC' refers to undefined symbol 'FIXED_MII_100_FDX'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When CONFIG_PROC_FS is not set and CONFIG_PPPOL2TP is set,
we have the following warning in build:
drivers/net/pppol2tp.c: In function 'pppol2tp_init':
drivers/net/pppol2tp.c:2472: warning: label
'out_unregister_pppox_proto' defined but not used
This patches fixes this warning by adding appropriate #ifdef.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use netdev_alloc_skb
- remove an useless variable in the IRQ handler
- remove an unused private structure member
- fix a spelling mistake
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
r6040_init_ring_desc moves around but it is kept unchanged.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This checks if the DMA address is bigger than what the controller can manage.
It will reallocate the buffers in the GFP_DMA zone in that case.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two off-by-one errors resulting in array overflows
spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes four resource leakages.
In any error path we must deallocate the DMA frame slots we
previously allocated by request_slot().
This is done by storing the ring pointers before doing any ring
allocation and restoring the old pointers in case of an error.
This patch by Michael Buesch has been ported to b43legacy.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must drop any packets we are not able to encrypt.
We must not send them unencrypted or with an all-zero-key (which
basically is the same as unencrypted, from a security point of view).
This might only trigger shortly after resume before mac80211 reassociated
and reconfigured the keys.
It is safe to drop these packets, as the association they belong to
is not guaranteed anymore anyway.
This is a security fix in the sense that it prevents information leakage.
This patch by Michael Buesch has been ported to b43legacy.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes suspend/resume work with the b43legacy driver.
We must not overwrite the MAC addresses in the init function, as this
would also overwrite the MAC on resume. With an all-zero MAC the device
firmware is not able to ACK any received packets anymore.
Fix this by moving the initializion stuff that must be done on init but
not on resume to the start function.
Also zero out filter_flags to make sure we don't have some flags
from a previous instance for a tiny timeframe until mac80211 reconfigures
them.
This patch by Michael Buesch has been ported to b43legacy.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Generic HDLC now uses random_ether_addr() for generating MAC addresse
for Ethernet-alike interfaces.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Just like our other drivers before we can switch ixgbe to
provide real-time packet/byte counters to the stack easily.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several counters behave differently on 82598 causing them to display
incorrect values. Adjust the accounting so the reported numbers
make sense and do not double count or represent the wrong item.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We were not returning CHECKSUM_NONE in a lot of cases which is
wrong. Move common exit points in this function and error code
up before the actual work in this function.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A gap was left in the FW release/grab code in up/down path. Fix
it by making the release/grab code a function and calling it in
appropriate locations.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The i82598 can support various media types but this ethtool
code only was coded for fiber just yet.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This ports Herbert Xu's "maybe_stop_tx" code and removes the tx_lock
which is not needed.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After testing we confirmed that the irq_sem can safely be
removed from ixgbe.
Add strict state checking code to various ethtool parts to
properly protect against races between various driver reset
paths.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes in other networking paths uncovered a bug in the xircom_cb
driver which made the kernel spew lots of the following error messages:
BUG eth1 code -5 qlen 0
It turned out that the driver returned -EIO when there was no
descriptor available for sending packets. It should return
NETDEV_TX_BUSY instead. This was discussed on the netdev list before,
see http://thread.gmane.org/gmane.linux.network/84603 .
Signed-off-by: Erik Mouw <mouw@nl.linux.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a check for the pci_register_driver() return value. Removed unused
variable pad_allocated.
The aim of this patch is to remove the following warning messages:
drivers/net/tlan.c: In function 'tlan_probe':
drivers/net/tlan.c:486: warning: ignoring return value of 'pci_register_driver', declared with attribute warn_unused_result
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Marvell Orion system on chips have an integrated mv643xx MAC. On these
little endian ARM devices mv643xx will oops when checksum offload is
enabled. Swapping the byte order of the protocol and checksum solves this
problem.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Manish Lachwani <mlachwani@mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon FE chip has a ram buffer therefore it needs the alignment
restriction and hang check workarounds.
Therefore:
* Autodetect the prescence/absence of ram buffer
* Rename the flag value to reflect this
* Use it consistently (ie don't reread register)
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: vmlinux.o(.text+0x25dca0): Section mismatch in reference from the function .veth_probe() to the function .init.text:.veth_probe_one()
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add a driver for NetEffect RNICs
IB/mthca: Return proper error codes from mthca_fmr_alloc()
IB: Avoid marking __devinitdata as const
IB/mlx4: Actually print out the driver version
IB/ib_mthca: Pre-link receive WQEs in Tavor mode
IB/mthca: Remove checks for srq->first_free < 0
IB/fmr_pool: Allocate page list for pool FMRs only when caching enabled
IB/srp: Retry stale connections
mlx4_core: Don't read reserved fields in mlx4_QUERY_ADAPTER()
IB/mthca: Don't read reserved fields in mthca_QUERY_ADAPTER()
IPoIB: Remove a misleading debug print
IPoIB: Handle bonding failover race for connected neighbours too
IB/mthca: Fix and simplify page size calculation in mthca_reg_phys_mr()
IB/ehca: Add PMA support
IB/ehca: Update sma_attr also in case of disruptive config change
IB/ehca: Prevent sending UD packets to QP0
IB/cm: Add interim support for routed paths
mlx4_core: Fix more section mismatches
Modify the b43 driver to avoid deadlocking suspend and resume, which happens
as a result of attempting to unregister device objects locked by the PM core
during suspend/resume cycles. Also, make it use a suspend-safe method of
unregistering device object in the resume error path.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace latency.c use with pm_qos_params use.
Signed-off-by: mark gross <mgross@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checking if an address is a vmalloc address is done in a couple of places.
Define a common version in mm.h and replace the other checks.
Again the include structures suck. The definition of VMALLOC_START and
VMALLOC_END is not available in vmalloc.h since highmem.c cannot be included
there.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixing:
CHECK drivers/net/pcmcia/pcnet_cs.c
drivers/net/pcmcia/pcnet_cs.c:523:15: warning: symbol 'hw_info' shadows an earlier one
drivers/net/pcmcia/pcnet_cs.c:148:18: originally declared here
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixing:
CHECK drivers/net/pcmcia/fmvj18x_cs.c
drivers/net/pcmcia/fmvj18x_cs.c:1205:6: warning: symbol 'i' shadows an earlier one
drivers/net/pcmcia/fmvj18x_cs.c:1179:9: originally declared here
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use 'max(x,y)' instead of 'x < y ? y : x'.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixing:
CHECK drivers/net/pcmcia/axnet_cs.c
drivers/net/pcmcia/axnet_cs.c:994:5: warning: symbol 'ax_close' was not declared. Should it be static?
drivers/net/pcmcia/axnet_cs.c:1017:6: warning: symbol 'ei_tx_timeout' was not declared. Should it be static?
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixing:
CHECK drivers/net/pcmcia/3c574_cs.c
drivers/net/pcmcia/3c574_cs.c:695:7: warning: symbol 'i' shadows an earlier one
drivers/net/pcmcia/3c574_cs.c:636:6: originally declared here
Signed-off-by: Richard Knutson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove kio_addr_t, and replace it with unsigned int. No known architecture
needs more than 32 bits for IO addresses and ports and having a separate type
for it is just messy.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Kconfig of igb and enc28j60 contains references to
obsolet Documentation/networking/net-modules.txt.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: "Nathaniel Filardo" <nwfilardo@gmail.com>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=9806
The TUN/TAP driver only permits one-way transitions of IFF_NO_PI or
IFF_ONE_QUEUE during the lifetime of a tap/tun interface. Note that
tun_set_iff contains
541 if (ifr->ifr_flags & IFF_NO_PI)
542 tun->flags |= TUN_NO_PI;
543
544 if (ifr->ifr_flags & IFF_ONE_QUEUE)
545 tun->flags |= TUN_ONE_QUEUE;
This is easily fixed by adding else branches which clear these bits.
Steps to reproduce:
This is easily reproduced by setting an interface persistant using tunctl then
attempting to open it as IFF_TAP or IFF_TUN, without asserting the IFF_NO_PI
flag. The ioctl() will succeed and the ifr.flags word is not modified, but the
interface remains in IFF_NO_PI mode (as it was set by tunctl).
Acked-by: Maxim Krasnyansky <maxk@qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
hw[] is used in both init and exit functions so it cannot be initdata (section
mismatch is when CONFIG_MODULES=n and CONFIG_DMASCC=y).
WARNING: vmlinux.o(.exit.text+0xba7): Section mismatch: reference to .init.data: (between 'dmascc_exit' and 'sixpack_exit_driver')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Klaus Kudielka <klaus.kudielka@gmx.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.
Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 3d73c288 ("mlx4_core: Fix section mismatches") fixed some of
the section mismatches introduced when error recovery was added, but
there were still more cases of errory recovery code calling into
__devinit code from regular .text. Fix this by getting rid of the
now-incorrect __devinit annotations.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (25 commits)
virtio: balloon driver
virtio: Use PCI revision field to indicate virtio PCI ABI version
virtio: PCI device
virtio_blk: implement naming for vda-vdz,vdaa-vdzz,vdaaa-vdzzz
virtio_blk: Dont waste major numbers
virtio_blk: provide getgeo
virtio_net: parametrize the napi_weight for virtio receive queue.
virtio: free transmit skbs when notified, not on next xmit.
virtio: flush buffers on open
virtnet: remove double ether_setup
virtio: Allow virtio to be modular and used by modules
virtio: Use the sg_phys convenience function.
virtio: Put the virtio under the virtualization menu
virtio: handle interrupts after callbacks turned off
virtio: reset function
virtio: populate network rings in the probe routine, not open
virtio: Tweak virtio_net defines
virtio: Net header needs hdr_len
virtio: remove unused id field from struct virtio_blk_outhdr
virtio: clarify NO_NOTIFY flag usage
...
This fixes a potential dangling xmit problem.
We also suppress refill interrupts until we need them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix bug found by Christian Borntraeger: if the other side fills all
the registered network buffers before we enable NAPI, we will never
get an interrupt. The simplest fix is to process the input queue once
on open.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Hello Rusty,
virtnet_probe already calls alloc_etherdev, which calls ether_setup.
There is no need to do that again.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch moves virtio under the virtualization menu and changes virtio
devices to not claim to only be for lguest.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A reset function solves three problems:
1) It allows us to renegotiate features, eg. if we want to upgrade a
guest driver without rebooting the guest.
2) It gives us a clean way of shutting down virtqueues: after a reset,
we know that the buffers won't be used by the host, and
3) It helps the guest recover from messed-up drivers.
So we remove the ->shutdown hook, and the only way we now remove
feature bits is via reset.
We leave it to the driver to do the reset before it deletes queues:
the balloon driver, for example, needs to chat to the host in its
remove function.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Since we want to reset the device to remove them, this is simpler
(device is reset for us on driver remove).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1) Turn GSO on virtio net into an all-or-nothing (keep checksumming
separate). Having multiple bits is a pain: if you can't support something
you should handle it in software, which is still a performance win.
2) Make VIRTIO_NET_HDR_GSO_ECN a flag in the header, so it can apply to
IPv6 or v4.
3) Rename VIRTIO_NET_F_NO_CSUM to VIRTIO_NET_F_CSUM (ie. means we do
checksumming).
4) Add csum and gso params to virtio_net to allow more testing.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It's far easier to deal with packets if we don't have to parse the
packet to figure out the header length to know how much to pull into
the skb data. Add the field to the virtio_net_hdr struct (and fix the
spaces that somehow crept in there).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It seems that virtio_net wants to disable callbacks (interrupts) before
calling netif_rx_schedule(), so we can't use the return value to do so.
Rename "restart" to "cb_enable" and introduce "cb_disable" hook: callback
now returns void, rather than a boolean.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
