NUMA is broken on alpha; marked as such
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Coverity checker.
(akpm: I stole this from Greg's tree and used the (IMO) tidier sizeof(*p)
construct).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We weren't actually waking up the md thread after setting
MD_RECOVERY_NEEDED when assembling an array, so it is possible to lose a
race and not actually start resync.
So add a call to md_wakeup_thread, and while we are at it, remove all the
"if (mddev->thread)" guards as md_wake_thread does its own checking.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_PREEMPT && !CONFIG_SMP, it's possible for sys_getppid to
return a bogus value if the parent's task_struct gets reallocated after
current->group_leader->real_parent is read:
asmlinkage long sys_getppid(void)
{
int pid;
struct task_struct *me = current;
struct task_struct *parent;
parent = me->group_leader->real_parent;
RACE HERE => for (;;) {
pid = parent->tgid;
#ifdef CONFIG_SMP
{
struct task_struct *old = parent;
/*
* Make sure we read the pid before re-reading the
* parent pointer:
*/
smp_rmb();
parent = me->group_leader->real_parent;
if (old != parent)
continue;
}
#endif
break;
}
return pid;
}
If the process gets preempted at the indicated point, the parent process
can go ahead and call exit() and then get wait()'d on to reap its
task_struct. When the preempted process gets resumed, it will not do any
further checks of the parent pointer on !CONFIG_SMP: it will read the
bad pid and return.
So, the same algorithm used when SMP is enabled should be used when
preempt is enabled, which will recheck ->real_parent in this case.
Signed-off-by: David Meybohm <dmeybohmlkml@bellsouth.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This trips up a lot of folks reading this code.
Put an unlikely() around the port-exhaustion test
for good measure.
Signed-off-by: David S. Miller <davem@davemloft.net>
Intention of this bit is to force pushing of the existing
send queue when TCP_CORK or TCP_NODELAY state changes via
setsockopt().
But it's easy to create a situation where the bit never
clears. For example, if the send queue starts empty:
1) set TCP_NODELAY
2) clear TCP_NODELAY
3) set TCP_CORK
4) do small write()
The current code will leave TCP_NAGLE_PUSH set after that
sequence. Unconditionally clearing the bit when new data
is added via skb_entail() solves the problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_create_dflt() is missing to destroy the newly allocated
default qdisc if the initialization fails resulting in leaks
of all kinds. The only caller in mainline which may trigger
this bug is sch_tbf.c in tbf_create_dflt_qdisc().
Note: qdisc_create_dflt() doesn't fulfill the official locking
requirements of qdisc_destroy() but since the qdisc could
never be seen by the outside world this doesn't matter
and it can stay as-is until the locking of pkt_sched
is cleaned up.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SNMP_MIB_SENTINEL to the definition of the sctp_snmp_list so that
the output routine in proc correctly terminates. This was causing some
problems running on ia64 systems.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Brown paperbag bug - ax25_findbyuid() was always returning a NULL pointer
as the result. Breaks ROSE completly and AX.25 if UID policy set to deny.
o While the list structure of AX.25's UID to callsign mapping table was
properly protected by a spinlock, it's elements were not refcounted
resulting in a race between removal and usage of an element.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket flag cleanups that went into 2.6.12-rc1 are basically oring
the flags of an old socket into the socket just being created.
Unfortunately that one was just initialized by sock_init_data(), so already
has SOCK_ZAPPED set. As the result zapped sockets are created and all
incoming connection will fail due to this bug which again was carefully
replicated to at least AX.25, NET/ROM or ROSE.
In order to keep the abstraction alive I've introduced sock_copy_flags()
to copy the socket flags from one sockets to another and used that
instead of the bitwise copy thing. Anyway, the idea here has probably
been to copy all flags, so sock_copy_flags() should be the right thing.
With this the ham radio protocols are usable again, so I hope this will
make it into 2.6.13.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checksum needs to be filled in on output, after mangling a packet
ip_summed needs to be reset.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Dave Johnson <djohnson+linux-kernel@sw.starentnetworks.com>
Found this bug while doing some scaling testing that created 500K inet
peers.
peer_check_expire() in net/ipv4/inetpeer.c isn't using inet_peer_gc_mintime
correctly and will end up creating an expire timer with less than the
minimum duration, and even zero/negative if enough active peers are
present.
If >65K peers, the timer will be less than inet_peer_gc_mintime, and with
>70K peers, the timer duration will reach zero and go negative.
The timer handler will continue to schedule another zero/negative timer in
a loop until peers can be aged. This can continue for at least a few
minutes or even longer if the peers remain active due to arriving packets
while the loop is occurring.
Bug is present in both 2.4 and 2.6. Same patch will apply to both just
fine.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While I was going through the crypto users recently, I noticed this
bogus kmap in sunrpc. It's totally unnecessary since the crypto
layer will do its own kmap before touching the data. Besides, the
kmap is throwing the return value away.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the tail SKB fits into the window, it is still
benefitical to defer until the goal percentage of
the window is available. This give the application
time to feed more data into the send queue and thus
results in larger TSO frames going out.
Patch from Dmitry Yusupov <dima@neterion.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Stephane, we've now worked out the real cause of the
`Linux will not boot on simulator' problem. Turns out it's a stack
overflow because the stack pointer wasn't being initialised properly
in boot_head.S (it was being initialised to the lowest instead of the
highest address of the stack, so the first push started to overwrite
data in the BSS).
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Re-order release_region calls in i810_probe to properly unwind preceding
allocations.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The purpose of this patch:
- Adopt the DMA API (jazzsonic, macsonic & core driver).
- Adopt the driver model (macsonic).
This part was cribbed from jazzsonic. As a consequence, macsonic once
again works as a module. Driver model is also used by the DMA calls.
- Support 16 bit cards (macsonic & core driver, also affects jazzsonic)
This code was adapted from the mac68k linux 2.2 kernel, where it has
languished for a long time.
- Support more 32-bit mac cards (macsonic)
Also from mac68k repo.
- Zero-copy buffer handling (core driver)
Provides a nice performance improvement. The new algorithm incidentally
helped to replace the old Jazz DMA code.
The patch was tested on a variety of macs (several 32-bit quadra built-in
NICs, a 16-bit LC PDS NIC and a 16-bit comm-slot NIC), and also on MIPS
Jazz.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
As SII reports that only original 3112's are affected by M15W quirk,
This patch adds SIL_FLAG_MOD15WRITE to selectively apply M15W quirk
depending on chipsets. As of yet, we don't know exactly which PCI IDs
are for original 3112, so M15W quirk is applied to all except for 3512
and 3124. Once more info is avaliable, we can change some of these
sil_3112_m15w's to sil_3112.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH libata-dev-2.6:upstream] implement ata_poll_qc_complete and use it in polling functions
Previously, libata polling functions turned irq back on and completed
qc commands without holding host lock. This creates a race condition
between the polling task and interrupts from other ports on the same
host set or spurious interrupt from itself.
This patch implements ata_poll_qc_complete which enables irq and
completes qc atomically and convert all polling functions.
Note: atapi_packet_task() didn't use to turn irq back on or clear
ATA_FLAG_NOINTR on error exits. This patch makes it use
ata_poll_qc_complete which does both.
Note: With this change, ALL invocations of ata_qc_complete() are now
done under host_set lock.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Interrupts from devices sharing the same IRQ could cause
ata_host_intr to finish commands being processed by atapi_packet_task
if the commands are using ATA_PROT_ATAPI_NODATA or ATA_PROT_ATAPI_DMA
protocol. This is because libata interrupt handler is unaware that
interrupts are not expected during that period. This patch adds
ATA_FLAG_NOINTR flag to tell the interrupt handler that we're not
expecting interrupts.
Note that once proper HSM is implemented for interrupt-driven PIO,
this should be merged into it and this flag will be removed.
ahci.c is a different kind of beast, so it's left alone.
* The following drivers use ata_qc_issue_prot and ata_interrupt, so
changes in libata core will do.
ata_piix sata_sil sata_svw sata_via sata_sis sata_uli
* The following drivers use ata_qc_issue_prot and custom intr handler.
They need this change to work correctly.
sata_nv sata_vsc
* The following drivers use custom issue function and intr handler.
Currently all custom issue functions don't support ATAPI, so this
change is irrelevant, updated for consistency and to avoid later
mistakes.
sata_promise sata_qstor sata_sx4
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch: fix wrong HD activity control by ahci driver
The ahci driver 1.0 sets the SActive bit on every transaction,
causing the LED to light up. The SActive bit is used only for
native command queuing (NCQ) which the current driver version
doesn't implement. Resetting the SActive bit is the device's
responsibility (by sending a "Set Device Bits FIS" to the
host adapter) but this is not required in response to
non-NCQ commands, and (most) devices don't. Thus the LED
stays always on. This patch fixes the LED behavior.
Spec references:
http://www.intel.com/technology/serialata/pdf/rev1_1.pdf, sec. 3.3.13, 5.5.1
http://www.serialata.org/docs/serialata10a.pdfhttp://www.intel.com/design/storage/papers/25266401.pdf
Signed-off-by: Martin.Wilck@fujitsu-siemens.com
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Promise TX4200 is a 4-port SATA controller based on the PDC40519 chip. It
meets the description of the 20319, so just a simple ID needs to be added to
support this hardware. Thanks to Martin Povolný for testing.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Otto Meier recently submitted a patch to support the PDC40718 chip (marketed
as SATA300 TX4, a 4-port SATA controller).
Signed-off-by: Otto Meier <gf435@gmx.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Description:
After calling the completion callback, the libata error handler might be
running and getting atapi sense data. Clearing the ATA_QCFLAG_ACTIVE flag
at this point might interfere with the libata error handler.
Changes:
- Clear the ATA_QCFLAG_ACTIVE flag before calling the completion callback
(and also before the error handler)
- Add some comment
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] [NET] mv643xx: add workaround for HW checksum generation bug
The hardware checksum generator on the mv64xxx occasionally generates
an incorrect checksum. This patch works around the issue and enables
hardware checksum generation.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Most importantly, remove bogus BUG() in receive path.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
An incorrect check made it bail out before doing anything.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Plug a race in TSC synchronization
We need to do tsc_sync_wait() before the CPU is set online to prevent
multiple CPUs from doing it in parallel - which won't work because TSC
sync has global unprotected state.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm trying to get the nmi working with my laptop (IBM ThinkPad G41) and after
debugging it a while, I found that the nmi code doesn't want to set it up for
this particular CPU.
Here I have:
$ cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Mobile Intel(R) Pentium(R) 4 CPU 3.33GHz
stepping : 1
cpu MHz : 3320.084
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pni
monitor ds_cpl est tm2 cid xtpr
bogomips : 6642.39
processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Mobile Intel(R) Pentium(R) 4 CPU 3.33GHz
stepping : 1
cpu MHz : 3320.084
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pni
monitor ds_cpl est tm2 cid xtpr
bogomips : 6637.46
And the following code shows:
$ cat linux-2.6.13-rc6/arch/i386/kernel/nmi.c
[...]
void setup_apic_nmi_watchdog (void)
{
switch (boot_cpu_data.x86_vendor) {
case X86_VENDOR_AMD:
if (boot_cpu_data.x86 != 6 && boot_cpu_data.x86 != 15)
return;
setup_k7_watchdog();
break;
case X86_VENDOR_INTEL:
switch (boot_cpu_data.x86) {
case 6:
if (boot_cpu_data.x86_model > 0xd)
return;
setup_p6_watchdog();
break;
case 15:
if (boot_cpu_data.x86_model > 0x3)
return;
Here I get boot_cpu_data.x86_model == 0x4. So I decided to change it and
reboot. I now seem to have a working NMI. So, unless there's something know
to be bad about this processor and the NMI. I'm submitting the following
patch.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Acked-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
