Enable compilation of the connection manager roam files with
Kbuild changes.
Add new API to store and retrieve the firmware scan channels at
mlme. Also add initial support to post SET_PCL command through
lim, so that it is not sent before ROAM init command.
Add changes to restrict connection of the 2nd STA to
channels on the other band of the 1st STA connected band.
This is done by filling only the allowed band channels in
the scan filters for the 2nd STA connection. If only
1 STA is active, it is allowed to connect on any band.
Add header gaurds for missed header files:
wlan_cm_tgt_if_tx_api.h
target_if_cm_roam_offload.h
Change-Id: Id2bce12b9663ed635ea46164169b088461aab870
CRs-Fixed: 2720341
In the noisy environment observation is, host sends SAE commit req to
AP and gets SAE commit response from AP, then host sends SAE confirm
req to AP but due to noisy environment AP miss the ack for SAE commit
response and keep sending SAE commit response even host send SAE
confirm. As host cleans SAE auth retry frames on reception of SAE auth
rx from AP, host cleanups SAE auth confirm req and disable SAE auth
retry timer. This leads to SAE auth failure. To avoid this host matches
auth frame's "sae algo sequence number" with last sent auth frame's "sae
algo sequence number", if it matches then only free sae auth retry frame
and deactivate sae auth retry timer.
Change-Id: Ia9ae2e5d82c696efdc0aaf4e04b6760b9829c510
CRs-Fixed: 2720436
For SAE auth frames, host configures auth retry timer to 1 second,
if host doesn't get ack for previously sent SAE auth frame then host
retransmit queued SAE auth frame once the periodic auth timer
triggers.
Due to noisy environment host may miss the SAE auth response, in this
case host needs to send queued SAE auth frame. Hence don't reset auth
retry timer on SAE auth TX ack reception.
Change-Id: I96456ce5cbe5fb2acc7005ff1d19c6e9eecc1764
CRs-Fixed: 2725359
For STA in 2.4Ghz band, host adds self HT supported channel width
capability in HT capability field of assoc request.
For WFA certification, expectation is to add self HT supported chan
width capability in HT capability field of assoc request.
Change-Id: I630423de03636e6c4ca07638dce6966c3ca381f9
CRs-Fixed: 2720908
TDLS Sta not initiating Add BA request or responding to Add BA
request from peer. For TDLS connection, legacy rate is
set to zero even though the peer capabilities supports OFDM rates.
The set of available rates from supplicant is compared with config
and rates is populated, which causes the issue.
Fix is to apply the correct rates provided from supplicant
change-ID: I66ce1b0ee4e5f96f9bb755a40ff7d8c46176087c
CRs-Fixed: 2719391
In STA+SAP case if AP1 and STA1 have same MAC, and DUT's STA is
connected to AP1. Now when the STA1 tries to connect with DUT's SAP
peer with same mac is already present the add peer fails, but during
delete peer the DUT STA peer (AP1) is deleted instead of STA1 of
DUT's SAP. This leads to SAP deleting peer of a STA interface and
thus the SAP peer count is out of sync.
Fix is to reject any association req from STA1 if AP1 is connected
to DUT's STA. Also ad vdev check while deleting the peer in wma.
Change-Id: I448226497c7aa3c11cb9097be9c7d57eb4239900
CRs-Fixed: 2723814
print “tx_complete" values in lim_auth_tx_complete_cnf and
lim_assoc_tx_complete_cnf along with success/fail as well
Change-Id: I0fe60da725df0b90d2e0957877c53bc793826dc6
CRs-Fixed: 2722114
For WFA certification testing, host updates station's max nss support
value in the omn ie of association request.
Change-Id: I0b001e0a0953aff0ff8ba614fab3e67c23eb2cfa
CRs-Fixed: 2690460
Currently, after roaming only vht ie is used to get dot11 mode
which may casue issue whenever vendor vht ie is present but vht
ie is not present in beacon. Host updates dot11 mode to
11N based on missing vht ie and does not consider vendor vht but
fw considers vendor vht ie which causes different dot11 modes in
fw and host.
Consider phy mode sent by fw in roam sync event to get dot11
mode to maintain compatibility between host and fw.
Change-Id: Ie9e4cbadd84d239c6f386f296c77677b15ce0500
CRs-Fixed: 2714566
As per requirement, the driver should able to process up to
MAX_MEASUREMENT_REQUEST (5) measurement request in a single
beacon report request.
Update driver logic to process up to 5 measurement request and
make sure the driver should not issue rrm scan for the duplicate
channel.
Change-Id: Iea3be8a0efef605852ac6b6b54dd06774ac0adac
CRs-Fixed: 2712112
To process up to 5 Measurement Request in a single beacon
report request, modify the size of Measurement Request IE
to 5.
Change-Id: I87025ce12886cc3129b01de6eb48b45e85babe9a
CRs-Fixed: 2712109
Host retransmits WPA3 SAE authentication frames after 1 second
if there is no response for previous auth frames from AP.
Host keep retransmitting SAE auth frames for max WLAN_SAE_AUTH_RETRY
times.
Change-Id: I1be0bd5354586518781876646b063592e667b0bb
CRs-Fixed: 2716719
Currently the driver calls the BLM API
to add the BSSID to the reject list if
STA kickout event comes from the FW.
Now since the event comes in interrupt
context and BLM takes a mutex lock, it
is not allowed.
Fix is to change the context
and call the BLM API from lim del sta
which would execute in scheduler
thread.
Change-Id: I3c2726ea152eeeee6ae30d80388aedac631f6c39
CRs-Fixed: 2716192
This change corresponds to the callback updates in scheduler_msg.
Changes include:
1. Update hdd_data_stall_process_event and its caller
2. Update umac_stop logic to allocate buffer for callback
and update its caller
3. Register beacon reporting callback as a direct function
call without message posting.
Change-Id: Ic07a6102ea75d8bccb57a800e9670750e98356ce
CRs-fixed: 2718977
