This patch set supports large block size(>4k, <=64k) in ext3 just enlarging
the block size limit. But it is NOT possible to have 64kB blocksize on
ext3 without some changes to the directory handling code. The reason is
that an empty 64kB directory block would have a rec_len == (__u16)2^16 ==
0, and this would cause an error to be hit in the filesystem. The proposed
solution is treat 64k rec_len with a an impossible value like rec_len =
0xffff to handle this.
The Patch-set consists of the following 2 patches.
[1/2] ext3: enlarge blocksize
- Allow blocksize up to pagesize
[2/2] ext3: fix rec_len overflow
- prevent rec_len from overflow with 64KB blocksize
Now on 64k page ppc64 box runs with this patch set we could create a 64k
block size ext3, and able to handle empty directory block.
Signed-off-by: Takashi Sato <sho@tnes.nec.co.jp>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When resizing online, setup_new_group_blocks attempts to reserve a
potentially very large transaction, depending on the current filesystem
geometry. For some journal sizes, there may not be enough room for this
transaction, and the online resize will fail.
The patch below resizes & restarts the transaction as necessary while
setting up the new group, and should work with even the smallest journal.
Tested with something like:
[root@newbox ~]# dd if=/dev/zero of=fsfile bs=1024 count=32768
[root@newbox ~]# mkfs.ext3 -b 1024 fsfile 16384
[root@newbox ~]# mount -o loop fsfile mnt/
[root@newbox ~]# resize2fs /dev/loop0
resize2fs 1.40.2 (12-Jul-2007)
Filesystem at /dev/loop0 is mounted on /root/mnt; on-line resizing required
old desc_blocks = 1, new_desc_blocks = 1
Performing an on-line resize of /dev/loop0 to 32768 (1k) blocks.
resize2fs: No space left on device While trying to add group #2
[root@newbox ~]# dmesg | tail -n 1
JBD: resize2fs wants too many credits (258 > 256)
[root@newbox ~]#
With the below change, it works.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Andreas Dilger <adilger@clusterfs.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_EXT3_INDEX is not an exposed config option in the kernel, and it is
unconditionally defined in ext3_fs.h. tune2fs is already able to turn off
dir indexing, so at this point it's just cluttering up the code. Remove
it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix f_version type: should be u64 instead of long
There is a type inconsistency between struct inode i_version and struct file
f_version.
fs.h:
struct inode
u64 i_version;
and
struct file
unsigned long f_version;
Users do:
fs/ext3/dir.c:
if (filp->f_version != inode->i_version) {
So why isn't f_version a u64 ? It becomes a problem if versions gets
higher than 2^32 and we are on an architecture where longs are 32 bits.
This patch changes the f_version type to u64, and updates the users accordingly.
It applies to 2.6.23-rc2-mm2.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Martin Bligh <mbligh@google.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: <linux-ext4@vger.kernel.org>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a new block bitmap is read from disk in read_block_bitmap() there are
a few bits that should ALWAYS be set. In particular, the blocks given by
ext4_blk_bitmap, ext4_inode_bitmap and ext4_inode_table. Validate the
block bitmap against these blocks.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Acked-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ext[234]_get_group_desc never tests the bh argument, and only sets it if it
is passed in; it is perfectly happy with a NULL bh argument. But, many
callers send one in and never use it. May as well call with NULL like
other callers who don't use the bh.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_percpu can fail, propagate that error.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s/percpu_counter_sum/&_positive/
Because its consitent with percpu_counter_read*
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh spotted that some code does:
percpu_counter_add(&counter, -unsignedlong)
which, when the amount argument is of type s32, sort-of works thanks to
two's-complement. However when we'd change the type to s64 this breaks on 32bit
machines, because the promotion rules zero extend the unsigned number.
Provide percpu_counter_sub() to hide the s64 cast. That is:
percpu_counter_sub(&counter, foo)
is equal to:
percpu_counter_add(&counter, -(s64)foo);
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s/percpu_counter_mod/percpu_counter_add/
Because its a better name, _mod implies modulo.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various fixes and improvements
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Combine the file_ra_state members
unsigned long prev_index
unsigned int prev_offset
into
loff_t prev_pos
It is more consistent and better supports huge files.
Thanks to Peter for the nice proposal!
[akpm@linux-foundation.org: fix shift overflow]
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The do_split() function for htree dir blocks is intended to split a leaf
block to make room for a new entry. It sorts the entries in the original
block by hash value, then moves the last half of the entries to the new
block - without accounting for how much space this actually moves. (IOW,
it moves half of the entry *count* not half of the entry *space*). If by
chance we have both large & small entries, and we move only the smallest
entries, and we have a large new entry to insert, we may not have created
enough space for it.
The patch below stores each record size when calculating the dx_map, and
then walks the hash-sorted dx_map, calculating how many entries must be
moved to more evenly split the existing entries between the old block and
the new block, guaranteeing enough space for the new entry.
The dx_map "offs" member is reduced to u16 so that the overall map size
does not change - it is temporarily stored at the end of the new block, and
if it grows too large it may be overwritten. By making offs and size both
u16, we won't grow the map size.
Also add a few comments to the functions involved.
This fixes the testcase reported by hooanon05@yahoo.co.jp on the
linux-ext4 list, "ext3 dir_index causes an error"
Thanks to Andreas Dilger for discussing the problem & solution with me.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Tested-by: Junjiro Okajima <hooanon05@yahoo.co.jp>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: <linux-ext4@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert asserts (BUGs) in dx_probe from bad on-disk data to recoverable
errors with helpful warnings. With help catching other asserts from Duane
Griffin <duaneg@dghda.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Duane Griffin <duaneg@dghda.com>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we fail to start a transaction when releasing dquot, we have to call
dquot_release() anyway to mark dquot structure as inactive. Otherwise we
end in an infinite loop inside dqput().
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: xb <xavier.bru@bull.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ext[234]_check_descriptors sanity checks block group descriptor geometry at
mount time, testing whether the block bitmap, inode bitmap, and inode table
reside wholly within the blockgroup. However, the inode table test is off
by one so that if the last block in the inode table resides on the last
block of the block group, the test incorrectly fails. This is because it
tests the last block as (start + length) rather than (start + length - 1).
This can be seen by trying to mount a filesystem made such as:
mkfs.ext2 -F -b 1024 -m 0 -g 256 -N 3744 fsfile 1024
which yields:
EXT2-fs error (device loop0): ext2_check_descriptors: Inode table for group 0 not in group (block 101)!
EXT2-fs: group descriptors corrupted!
There is a similar bug in e2fsprogs, patch already sent for that.
(I wonder if inside(), outside(), and/or in_range() should someday be
used in this and other tests throughout the ext filesystems...)
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Split ondemand readahead interface into two functions. I think this makes it
a little clearer for non-readahead experts (like Rusty).
Internally they both call ondemand_readahead(), but the page argument is
changed to an obvious boolean flag.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert ext3/ext4 dir reads to use on-demand readahead.
Readahead for dirs operates _not_ on file level, but on blockdev level. This
makes a difference when the data blocks are not continuous. And the read
routine is somehow opaque: there's no handy info about the status of current
page. So a simplified call scheme is employed: to call into readahead
whenever the current page falls out of readahead windows.
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Cc: Steven Pratt <slpratt@austin.ibm.com>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce is_owner_or_cap() macro in fs.h, and convert over relevant
users to it. This is done because we want to avoid bugs in the future
where we check for only effective fsuid of the current task against a
file's owning uid, without simultaneously checking for CAP_FOWNER as
well, thus violating its semantics.
[ XFS uses special macros and structures, and in general looked ...
untouchable, so we leave it alone -- but it has been looked over. ]
The (current->fsuid != inode->i_uid) check in generic_permission() and
exec_permission_lite() is left alone, because those operations are
covered by CAP_DAC_OVERRIDE and CAP_DAC_READ_SEARCH. Similarly operations
falling under the purview of CAP_CHOWN and CAP_LEASE are also left alone.
Signed-off-by: Satyam Sharma <ssatyam@cse.iitk.ac.in>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: Serge E. Hallyn <serge@hallyn.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
currently the export_operation structure and helpers related to it are in
fs.h. fs.h is already far too large and there are very few places needing the
export bits, so split them off into a separate header.
[akpm@linux-foundation.org: fix cifs build]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a patch that speeds up statfs. It is very simple - the "overhead"
calculation, which takes a huge amount of time for large filesystems, never
changes unless the size of the filesystem itself changes. That means we can
store it in memory and only recalculate if the filesystem has been resized
(almost never).
It also fixes a minor problem that we never update the on-disk superblock free
blocks/inodes counts until the filesystem is unmounted. While not fatal, we
may as well update that on disk when we have the information, and it makes
things like debugfs and dumpe2fs report a bit more accurate info.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace (n & (n-1)) in the context of power of 2 checks with is_power_of_2()
Signed-off-by: vignesh babu <vignesh.babu@wipro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ext3_change_inode_journal_flag() is only called from one location:
ext3_ioctl(EXT3_IOC_SETFLAGS). That ioctl case already has a IS_RDONLY()
call in it so this one is superfluous.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ext3_orphan_add() and ext3_orphan_del() functions lock sb->s_lock with a
transaction started with ext3_mark_recovery_complete() waits for a transaction
holding sb->s_lock, thus leading to a possible deadlock. At the moment we
call ext3_mark_recovery_complete() from ext3_remount() we have done all the
work needed for remounting and thus we are safe to drop sb->s_lock before we
wait for transactions to commit. Note that at this moment we are still
guarded by s_umount lock against other remounts/umounts.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Eric Sandeen <sandeen@sandeen.net>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After ext3 orphan list check has been added into ext3_destroy_inode()
(please see my previous patch) the following situation has been detected:
EXT3-fs warning (device sda6): ext3_unlink: Deleting nonexistent file (37901290), 0
Inode 00000101a15b7840: orphan list check failed!
00000773 6f665f00 74616d72 00000573 65725f00 06737270 66000000 616d726f
...
Call Trace: [<ffffffff80211ea9>] ext3_destroy_inode+0x79/0x90
[<ffffffff801a2b16>] sys_unlink+0x126/0x1a0
[<ffffffff80111479>] error_exit+0x0/0x81
[<ffffffff80110aba>] system_call+0x7e/0x83
First messages said that unlinked inode has i_nlink=0, then ext3_unlink()
adds this inode into orphan list.
Second message means that this inode has not been removed from orphan list.
Inode dump has showed that i_fop = &bad_file_ops and it can be set in
make_bad_inode() only. Then I've found that ext3_read_inode() can call
make_bad_inode() without any error/warning messages, for example in the
following case:
...
if (inode->i_nlink == 0) {
if (inode->i_mode == 0 ||
!(EXT3_SB(inode->i_sb)->s_mount_state & EXT3_ORPHAN_FS)) {
/* this inode is deleted */
brelse (bh);
goto bad_inode;
...
Bad inode can live some time, ext3_unlink can add it to orphan list, but
ext3_delete_inode() do not deleted this inode from orphan list. As result
we can have orphan list corruption detected in ext3_destroy_inode().
However it is not clear for me how to fix this issue correctly.
As far as i see is_bad_inode() is called after iget() in all places
excluding ext3_lookup() and ext3_get_parent(). I believe it makes sense to
add bad inode check to these functions too and call iput if bad inode
detected.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Customers claims to ext3-related errors, investigation showed that ext3
orphan list has been corrupted and have the reference to non-ext3 inode.
The following debug helps to understand the reasons of this issue.
[akpm@linux-foundation.org: update for print_hex_dump() changes]
Signed-off-by: Vasily Averin <vvs@sw.ru>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They can use generic_file_splice_read() instead. Since sys_sendfile() now
prefers that, there should be no change in behaviour.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
One of error path in ext3_read_inode() leaks bh since brelse is forgoten.
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Acked-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use zero_user_page() instead of open-coding it.
Signed-off-by: Nate Diller <nate.diller@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A patch that stores inode flags such as S_IMMUTABLE, S_APPEND, etc. from
i_flags to EXT3_I(inode)->i_flags when inode is written to disk. The same
thing is done on GETFLAGS ioctl.
Quota code changes these flags on quota files (to make it harder for
sysadmin to screw himself) and these changes were not correctly propagated
into the filesystem (especially, lsattr did not show them and users were
wondering...).
Propagate flags such as S_APPEND, S_IMMUTABLE, etc. from i_flags into
ext3-specific i_flags. Hence, when someone sets these flags via a
different interface than ioctl, they are stored correctly.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- ext3_dx_find_entry() exit with out setting proper error pointer
- do_split() exit with out setting proper error pointer
it is realy painful because many callers contain folowing code:
de = do_split(handle,dir, &bh, frame, &hinfo, &retval);
if (!(de))
return retval;
<<< WOW retval wasn't changed by do_split(), so caller failed
<<< but return SUCCESS :)
- Rearrange do_split() error path. Current error path is realy ugly, all
this up and down jump stuff doesn't make code easy to understand.
[dmonakhov@sw.ru: fix annoying fake error messages]
Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org>
Cc: Andreas Dilger <adilger@clusterfs.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=5079
signed long ranges from -2.147.483.648 to 2.147.483.647 on x86 32bit
10000011110110100100111110111101 .. -2,082,844,739
10000011110110100100111110111101 .. 2,212,122,557 <- this currently gets
stored on the disk but when converting it to a 64bit signed long value it loses
its sign and becomes positive.
Cc: Andreas Dilger <adilger@dilger.ca>
Cc: <linux-ext4@vger.kernel.org>
Andreas says:
This patch is now treating timestamps with the high bit set as negative
times (before Jan 1, 1970). This means we lose 1/2 of the possible range
of timestamps (lopping off 68 years before unix timestamp overflow -
now only 30 years away :-) to handle the extremely rare case of setting
timestamps into the distant past.
If we are only interested in fixing the underflow case, we could just
limit the values to 0 instead of storing negative values. At worst this
will skew the timestamp by a few hours for timezones in the far east
(files would still show Jan 1, 1970 in "ls -l" output).
That said, it seems 32-bit systems (mine at least) allow files to be set
into the past (01/01/1907 works fine) so it seems this patch is bringing
the x86_64 behaviour into sync with other kernels.
On the plus side, we have a patch that is ready to add nanosecond timestamps
to ext3 and as an added bonus adds 2 high bits to the on-disk timestamp so
this extends the maximum date to 2242.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have never seen a use of SLAB_DEBUG_INITIAL. It is only supported by
SLAB.
I think its purpose was to have a callback after an object has been freed
to verify that the state is the constructor state again? The callback is
performed before each freeing of an object.
I would think that it is much easier to check the object state manually
before the free. That also places the check near the code object
manipulation of the object.
Also the SLAB_DEBUG_INITIAL callback is only performed if the kernel was
compiled with SLAB debugging on. If there would be code in a constructor
handling SLAB_DEBUG_INITIAL then it would have to be conditional on
SLAB_DEBUG otherwise it would just be dead code. But there is no such code
in the kernel. I think SLUB_DEBUG_INITIAL is too problematic to make real
use of, difficult to understand and there are easier ways to accomplish the
same effect (i.e. add debug code before kfree).
There is a related flag SLAB_CTOR_VERIFY that is frequently checked to be
clear in fs inode caches. Remove the pointless checks (they would even be
pointless without removeal of SLAB_DEBUG_INITIAL) from the fs constructors.
This is the last slab flag that SLUB did not support. Remove the check for
unimplemented flags from SLUB.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the destroy_dirty_buffers argument from invalidate_bdev(), it hasn't
been used in 6 years (so akpm says).
find * -name \*.[ch] | xargs grep -l invalidate_bdev |
while read file; do
quilt add $file;
sed -ie 's/invalidate_bdev(\([^,]*\),[^)]*)/invalidate_bdev(\1)/g' $file;
done
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert e92a4d595b.
Dmitry points out
"When we block_prepare_write() failed while ext3_prepare_write() we jump to
"failure" label and call ext3_prepare_failure() witch search last mapped bh
and invoke commit_write untill it. This is wrong!! because some bh from
begining to the last mapped bh may be not uptodate. As a result we commit to
disk not uptodate page content witch contains garbage from previous usage."
and
"Unexpected file size increasing."
Call trace the same as it was in first issue but result is different.
For example we have file with i_size is zero. we want write two blocks ,
but fs has only one free block.
->ext3_prepare_write(...from == 0, to == 2048)
retry:
->block_prepare_write() == -ENOSPC# we failed but allocated one block here.
->ext3_prepare_failure()
->commit_write( from == 0, to == 1024) # after this i_size becomes 1024 :)
if (ret == -ENOSPC && ext3_should_retry_alloc(inode->i_sb, &retries))
goto retry;
Finally when all retries will be spended ext3_prepare_failure return
-ENOSPC, but i_size was increased and later block trimm procedures can't
help here.
We don't appear to have the horsepower to fix these issues, so let's put
things back the way they were for now.
Cc: Kirill Korotaev <dev@openvz.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ken Chen <kenneth.w.chen@intel.com>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: <linux-ext4@vger.kernel.org>
Cc: Dmitriy Monakhov <dmonakhov@openvz.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A little mistake in 8a2bfdcbfa is making all
transactions synchronous, which reduces ext3 performance to comical levels.
Cc: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are race issues around ext[34] xattr block release code.
ext[34]_xattr_release_block() checks the reference count of xattr block
(h_refcount) and frees that xattr block if it is the last one reference it.
Unlike ext2, the check of this counter is unprotected by any lock.
ext[34]_xattr_release_block() will free the mb_cache entry before freeing
that xattr block. There is a small window between the check for the re
h_refcount ==1 and the call to mb_cache_entry_free(). During this small
window another inode might find this xattr block from the mbcache and reuse
it, racing a refcount updates. The xattr block will later be freed by the
first inode without notice other inode is still use it. Later if that
block is reallocated as a datablock for other file, then more serious
problem might happen.
We need put a lock around places checking the refount as well to avoid
racing issue. Another place need this kind of protection is in
ext3_xattr_block_set(), where it will modify the xattr block content in-
the-fly if the refcount is 1 (means it's the only inode reference it).
This will also fix another issue: the xattr block may not get freed at all
if no lock is to protect the refcount check at the release time. It is
possible that the last two inodes could release the shared xattr block at
the same time. But both of them think they are not the last one so only
decreased the h_refcount without freeing xattr block at all.
We need to call lock_buffer() after ext3_journal_get_write_access() to
avoid deadlock (because the later will call lock_buffer()/unlock_buffer
() as well).
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Cc: Andreas Gruenbacher <agruen@suse.de>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is inspired by Arjan's "Patch series to mark struct
file_operations and struct inode_operations const".
Compile tested with gcc & sparse.
Signed-off-by: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct inode_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
jbd function called instead of fs specific one.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Naming is confusing, ext3_inc_count manipulates i_nlink not i_count
- handle argument passed in is not used
- ext3 and ext4 already call inc_nlink and dec_nlink directly in other places
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return -ENOENT from ext[34]_link if we've raced with unlink and i_nlink is
0. Doing otherwise has the potential to corrupt the orphan inode list,
because we'd wind up with an inode with a non-zero link count on the list,
and it will never get properly cleaned up & removed from the orphan list
before it is freed.
[akpm@osdl.org: build fix]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix insecure default behaviour reported by Tigran Aivazian: if an ext2 or
ext3 or ext4 filesystem is tuned to mount with "acl", but mounted by a
kernel built without ACL support, then umask was ignored when creating
inodes - though root or user has umask 022, touch creates files as 0666,
and mkdir creates directories as 0777.
This appears to have worked right until 2.6.11, when a fix to the default
mode on symlinks (always 0777) assumed VFS applies umask: which it does,
unless the mount is marked for ACLs; but ext[234] set MS_POSIXACL in
s_flags according to s_mount_opt set according to def_mount_opts.
We could revert to the 2.6.10 ext[234]_init_acl (adding an S_ISLNK test);
but other filesystems only set MS_POSIXACL when ACLs are configured. We
could fix this at another level; but it seems most robust to avoid setting
the s_mount_opt flag in the first place (at the expense of more ifdefs).
Likewise don't set the XATTR_USER flag when built without XATTR support.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: <linux-ext4@vger.kernel.org>
Cc: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the rare case where we have skipped orphan inode processing due to a
readonly block device, and the block device subsequently changes back to
read-write, disallow a remount,rw transition of the filesystem when we have an
unprocessed orphan inodes as this would corrupt the list.
Ideally we should process the orphan inode list during the remount, but that's
trickier, and this plugs the hole for now.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change all the uses of f_{dentry,vfsmnt} to f_path.{dentry,mnt} in the ext3
filesystem.
Signed-off-by: Josef "Jeff" Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Port fix to the off-by-one in find_next_usable_block's memscan from ext2 to
ext3; but it didn't cause a serious problem for ext3 because the additional
ext3_test_allocatable check rescued it from the error.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ext3_new_blocks has a nice io_error label for setting -EIO, so goto that in
the one place that doesn't already use it.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The reservations tree is an rb_tree not a list, so it's less confusing to use
rb_entry() than list_entry() - though they're both just container_of().
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
rsv_end is the last block within the reservation, so alloc_new_reservation
should accept start_block == rsv_end as success.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
grp_goal 0 is a genuine goal (unlike -1), so ext3_try_to_allocate_with_rsv
should treat it as such.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ext3_new_blocks should reset the reservation window size to 0 when squeezing
the last blocks out of an almost full filesystem, so the retry doesn't skip
any groups with less than half that free, reporting ENOSPC too soon.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If you do something like:
# touch foo
# tail -f foo &
# rm foo
# <take snapshot>
# <mount snapshot>
you'll panic, because ext3/4 tries to do orphan list processing on the
readonly snapshot device, and:
kernel: journal commit I/O error
kernel: Assertion failure in journal_flush_Rsmp_e2f189ce() at journal.c:1356: "!journal->j_checkpoint_transactions"
kernel: Kernel panic: Fatal exception
for a truly readonly underlying device, it's reasonable and necessary
to just skip orphan list processing.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins wrote:
> Not found anything relevant, but I keep noticing these lines
> in ext2_try_to_allocate_with_rsv(), ext3 and ext4 similar:
>
> } else if (grp_goal > 0 &&
> (my_rsv->rsv_end - grp_goal + 1) < *count)
> try_to_extend_reservation(my_rsv, sb,
> *count-my_rsv->rsv_end + grp_goal - 1);
>
> They're wrong, a no-op in most groups, aren't they? rsv_end is an
> absolute block number, whereas grp_goal is group-relative, so the
> calculation ought to bring in group_first_block? Or I'm confused.
>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Cc: "linux-ext4@vger.kernel.org" <linux-ext4@vger.kernel.org>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In journal=ordered or journal=data mode retry in ext3_prepare_write()
breaks the requirements of journaling of data with respect to metadata.
The fix is to call commit_write to commit allocated zero blocks before
retry.
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ken Chen <kenneth.w.chen@intel.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've been using Steve Grubb's purely evil "fsfuzzer" tool, at
http://people.redhat.com/sgrubb/files/fsfuzzer-0.4.tar.gz
Basically it makes a filesystem, splats some random bits over it, then
tries to mount it and do some simple filesystem actions.
At best, the filesystem catches the corruption gracefully. At worst,
things spin out of control.
As you might guess, we found a couple places in ext3 where things spin out
of control :)
First, we had a corrupted directory that was never checked for
consistency... it was corrupt, and pointed to another bad "entry" of
length 0. The for() loop looped forever, since the length of
ext3_next_entry(de) was 0, and we kept looking at the same pointer over and
over and over and over... I modeled this check and subsequent action on
what is done for other directory types in ext3_readdir...
(adding this check adds some computational expense; I am testing a followup
patch to reduce the number of times we check and re-check these directory
entries, in all cases. Thanks for the idea, Andreas).
Next we had a root directory inode which had a corrupted size, claimed to
be > 200M on a 4M filesystem. There was only really 1 block in the
directory, but because the size was so large, readdir kept coming back for
more, spewing thousands of printk's along the way.
Per Andreas' suggestion, if we're in this read error condition and we're
trying to read an offset which is greater than i_blocks worth of bytes,
stop trying, and break out of the loop.
With these two changes fsfuzz test survives quite well on ext3.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
lock_super() is unnecessary for setting super-block feature flags. Use the
provided *_SET_COMPAT_FEATURE() macros as well.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update ext3_statfs to return an FSID that is a 64 bit XOR of the 128 bit
filesystem UUID as suggested by Andreas Dilger. See the following Bugzilla
entry for details:
http://bugzilla.kernel.org/show_bug.cgi?id=136
Cc: Andreas Dilger <adilger@clusterfs.com>
Cc: Stephen Tweedie <sct@redhat.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_NOFS is an alias of GFP_NOFS.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current error behaviour for ext2 and ext3 filesystems does not fully
correspond to the documentation and should be fixed.
According to man 8 mount, ext2 and ext3 file systems allow to set one of 3
different on-errors behaviours:
---- start of quote man 8 mount ----
errors=continue / errors=remount-ro / errors=panic
Define the behaviour when an error is encountered. (Either ignore
errors and just mark the file system erroneous and continue, or remount
the file system read-only, or panic and halt the system.) The default is
set in the filesystem superblock, and can be changed using tune2fs(8).
---- end of quote ----
However EXT3_ERRORS_CONTINUE is not read from the superblock, and thus
ERRORS_CONT is not saved on the sbi->s_mount_opt. It leads to the incorrect
handle of errors on ext3.
Then we've checked corresponding code in ext2 and discovered that it is buggy
as well:
- EXT2_ERRORS_CONTINUE is not read from the superblock (the same);
- parse_option() does not clean the alternative values and thus something
like (ERRORS_CONT|ERRORS_RO) can be set;
- if options are omitted, parse_option() does not set any of these options.
Therefore it is possible to set any combination of these options on the ext2:
- none of them may be set: EXT2_ERRORS_CONTINUE on superblock / empty mount
options;
- any of them may be set using mount options;
- 2 any options may be set: by using EXT2_ERRORS_RO/EXT2_ERRORS_PANIC on the
superblock and other value in mount options;
- and finally all three options may be set by adding third option in remount.
Currently ext2 uses these values only in ext2_error() and it is not leading to
any noticeable troubles. However somebody may be discouraged when he will try
to workaround EXT2_ERRORS_PANIC on the superblock by using errors=continue in
mount options.
This patch:
EXT3_ERRORS_CONTINUE should be taken from the superblock as default value for
error behaviour.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Acked-by: Vasily Averin <vvs@sw.ru>
Acked-by: Kirill Korotaev <dev@openvz.org>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some filesystems, instead of simply decrementing i_nlink, simply zero it
during an unlink operation. We need to catch these in addition to the
decrement operations.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is mostly included for parity with dec_nlink(), where we will have some
more hooks. This one should stay pretty darn straightforward for now.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a filesystem decrements i_nlink to zero, it means that a write must be
performed in order to drop the inode from the filesystem.
We're shortly going to have keep filesystems from being remounted r/o between
the time that this i_nlink decrement and that write occurs.
So, add a little helper function to do the decrements. We'll tie into it in a
bit to note when i_nlink hits zero.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes readv() and writev() methods and replaces them with
aio_read()/aio_write() methods.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch vectorizes aio_read() and aio_write() methods to prepare for
collapsing all aio & vectored operations into one interface - which is
aio_read()/aio_write().
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Michael Holzheu <HOLZHEU@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the Ext3 device ioctl compat stuff from fs/compat_ioctl.c to the Ext3
driver so that the Ext3 header file doesn't need to be included.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This eliminates the i_blksize field from struct inode. Filesystems that want
to provide a per-inode st_blksize can do so by providing their own getattr
routine instead of using the generic_fillattr() function.
Note that some filesystems were providing pretty much random (and incorrect)
values for i_blksize.
[bunk@stusta.de: cleanup]
[akpm@osdl.org: generic_fillattr() fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Rougly half of callers already do it by not checking return value
* Code in drivers/acpi/osl.c does the following to be sure:
(void)kmem_cache_destroy(cache);
* Those who check it printk something, however, slab_error already printed
the name of failed cache.
* XFS BUGs on failed kmem_cache_destroy which is not the decision
low-level filesystem driver should make. Converted to ignore.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some of the changes in balloc.c are just cosmetic, as Andreas pointed out -
if they overflow they'll then underflow and things are fine.
5th hunk actually fixes an overflow problem.
Also check for potential overflows in inode & block counts when resizing.
Signed-off-by: Eric Sandeen <esandeen@redhat.com>
Cc: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixing up some endian-ness warnings in preparation to clone ext4 from ext3.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
More white space cleanups in preparation of cloning ext4 from ext3.
Removing spaces that precede a tab.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SWsoft Virtuozzo/OpenVZ Linux kernel team has discovered that ext3 error
behavior was broken in linux kernels since 2.5.x versions by the following
patch:
2002/10/31 02:15:26-05:00 tytso@snap.thunk.org
Default mount options from superblock for ext2/3 filesystems
http://linux.bkbits.net:8080/linux-2.6/gnupatch@3dc0d88eKbV9ivV4ptRNM8fBuA3JBQ
In case ext3 file system is mounted with errors=continue
(EXT3_ERRORS_CONTINUE) errors should be ignored when possible. However at
present in case of any error kernel aborts journal and remounts filesystem
to read-only. Such behavior was hit number of times and noted to differ
from that of 2.4.x kernels.
This patch fixes this:
- do nothing in case of EXT3_ERRORS_CONTINUE,
- set EXT3_MOUNT_ABORT and call journal_abort() in all other cases
- panic() should be called after ext3_commit_super() to save
sb marked as EXT3_ERROR_FS
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Kirill Korotaev <dev@sw.ru>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Cc: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the past there were a few kernel panics related to block reservation
tree operations failure (insert/remove etc). It would be very useful to
get the block allocation reservation map info when such error happens.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is primarily format string fixes, with changes to ialloc.c where large
inode counts could overflow, and also pass around journal_inum as an
unsigned long, just to be pedantic about it....
Signed-off-by: Eric Sandeen <esandeen@redhat.com>
Cc: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I need to do some actual IO testing now, but this gets things mounting for
a 16T ext3 filesystem. (patched up e2fsprogs is needed too, I'll send that
off the kernel list)
This patch fixes these issues in the kernel:
o sbi->s_groups_count overflows in ext3_fill_super()
sbi->s_groups_count = (le32_to_cpu(es->s_blocks_count) -
le32_to_cpu(es->s_first_data_block) +
EXT3_BLOCKS_PER_GROUP(sb) - 1) /
EXT3_BLOCKS_PER_GROUP(sb);
at 16T, s_blocks_count is already maxed out; adding
EXT3_BLOCKS_PER_GROUP(sb) overflows it and groups_count comes out to 0.
Not really what we want, and causes a failed mount.
Feel free to check my math (actually, please do!), but changing it this
way should work & avoid the overflow:
(A + B - 1)/B changed to: ((A - 1)/B) + 1
o ext3_check_descriptors() overflows range checks
ext3_check_descriptors() iterates over all block groups making sure
that various bits are within the right block ranges... on the last pass
through, it is checking the error case
[item] >= block + EXT3_BLOCKS_PER_GROUP(sb)
where "block" is the first block in the last block group. The last
block in this group (and the last one that will fit in 32 bits) is block
+ EXT3_BLOCKS_PER_GROUP(sb)- 1. block + EXT3_BLOCKS_PER_GROUP(sb) wraps
back around to 0.
so, make things clearer with "first_block" and "last_block" where those
are first and last, inclusive, and use <, > rather than <, >=.
Finally, the last block group may be smaller than the rest, so account
for this on the last pass through: last_block = sb->s_blocks_count - 1;
(a similar patch could be done for ext2; does anyone in their right mind
use ext2 at 16T? I'll send an ext2 patch doing the same thing if that's
warranted)
Signed-off-by: Eric Sandeen <esandeen@redhat.com>
Cc: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove whitespace from ext3 and jbd, before we clone ext4.
Signed-off-by: Mingming Cao<cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ext3-get-blocks support caused ~20% degrade in Sequential read
performance (tiobench). Problem is with marking the buffer boundary
so IO can be submitted right away. Here is the patch to fix it.
2.6.18-rc6:
-----------
# ./iotest
1048576+0 records in
1048576+0 records out
4294967296 bytes (4.3 GB) copied, 75.2726 seconds, 57.1 MB/s
real 1m15.285s
user 0m0.276s
sys 0m3.884s
2.6.18-rc6 + fix:
-----------------
[root@elm3a241 ~]# ./iotest
1048576+0 records in
1048576+0 records out
4294967296 bytes (4.3 GB) copied, 62.9356 seconds, 68.2 MB/s
The boundary block check in ext3_get_blocks_handle needs to be adjusted
against the count of blocks mapped in this call, now that it can map
more than one block.
Signed-off-by: Suparna Bhattacharya <suparna@in.ibm.com>
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Inodes earlier than the 'first' inode (e.g. journal, resize) should be
rejected early - except the root inode. Also inode numbers that are too
big should be rejected early.
[akpm@osdl.org: cleanup]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It has been reported that ext3_getblk() is not doing the right thing and
triggering following WARN():
BUG: warning at fs/ext3/inode.c:1016/ext3_getblk()
<c01c5140> ext3_getblk+0x98/0x2a6 <c03b2806> md_wakeup_thread+0x26/0x2a
<c01c536d> ext3_bread+0x1f/0x88 <c01cedf9> ext3_quota_read+0x136/0x1ae
<c018b683> v1_read_dqblk+0x61/0xac <c0188f32> dquot_acquire+0xf6/0x107
<c01ceaba> ext3_acquire_dquot+0x46/0x68 <c01897d4> dqget+0x155/0x1e7
<c018a97b> dquot_transfer+0x3e0/0x3e9 <c016fe52> dput+0x23/0x13e
<c01c7986> ext3_setattr+0xc3/0x240 <c0120f66> current_fs_time+0x52/0x6a
<c017320e> notify_change+0x2bd/0x30d <c0159246> chown_common+0x9c/0xc5
<c02a222c> strncpy_from_user+0x3b/0x68 <c0167fe6> do_path_lookup+0xdf/0x266
<c016841b> __user_walk_fd+0x44/0x5a <c01592b9> sys_chown+0x4a/0x55
<c015a43c> vfs_write+0xe7/0x13c <c01695d4> sys_mkdir+0x1f/0x23
<c0102a97> syscall_call+0x7/0xb
Looking at the code, it looks like it's not handle HOLE correctly. It ends
up returning -EIO. Here is the patch to fix it.
If we really want to be paranoid, we can allow return values 0 (HOLE), 1
(we asked for one block) and return -EIO for more than 1 block. But I
really don't see a reason for doing it - all we need is the block# here.
(doesn't matter how many blocks are mapped).
ext3_get_blocks_handle() returns number of blocks it mapped. It returns 0
in case of HOLE. ext3_getblk() should handle HOLE properly (currently its
dumping warning stack and returning -EIO).
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To handle the earlier bogus ENOSPC error caused by filesystem full of block
reservation, current code falls back to non block reservation, starts to
allocate block(s) from the goal allocation block group as if there is no
block reservation.
Current code needs to re-load the corresponding block group descriptor for
the initial goal block group in this case. The patch fixes this.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For files other than IFREG, nobh option doesn't make sense. Modifications
to them are journalled and needs buffer heads to do that. Without this
patch, we get kernel oops in page_buffers().
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The inode number out of an NFS file handle gets passed eventually to
ext3_get_inode_block() without any checking. If ext3_get_inode_block()
allows it to trigger an error, then bad filehandles can have unpleasant
effect - ext3_error() will usually cause a forced read-only remount, or a
panic if `errors=panic' was used.
So remove the call to ext3_error there and put a matching check in
ext3/namei.c where inode numbers are read off storage.
[akpm@osdl.org: fix off-by-one error]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: <stable@kernel.org>
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Cc: Eric Sandeen <esandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These functions no longer exist; remove their declarations.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The quota code plays interesting games with the lock ordering; to quote Jan:
| i_mutex of inode containing quota file is acquired after all other
| quota locks. i_mutex of all other inodes is acquired before quota
| locks. Quota code makes sure (by resetting inode operations and
| setting special flag on inode) that noone tries to enter quota code
| while holding i_mutex on a quota file...
The good news is that all of this special case i_mutex grabbing happens in the
(per filesystem) low level quota write function. For this special case we
need a new I_MUTEX_* nesting level, since this just entirely outside any of
the regular VFS locking rules for i_mutex. I trust Jan on his blue eyes that
this is not ever going to deadlock; and based on that the patch below is what
it takes to inform lockdep of these very interesting new locking rules.
The new locking rule for the I_MUTEX_QUOTA nesting level is that this is the
deepest possible level of nesting for i_mutex, and that this only should be
used in quota write (and possibly read) function of filesystems. This makes
the lock ordering of the I_MUTEX_* levels:
I_MUTEX_PARENT -> I_MUTEX_CHILD -> I_MUTEX_NORMAL -> I_MUTEX_QUOTA
Has no effect on non-lockdep kernels.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Same as with already do with the file operations: keep them in .rodata and
prevents people from doing runtime patching.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds "-o bh" option to force use of buffer_heads. This option
is needed when we make "nobh" as default - and if we run into problems.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The variables nlen and rlen are defined/initialized but not used in
ext3_add_entry().
Signed-off-by: Johann Lombardi <johann.lombardi@bull.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the ext3 in-kernel filesystem blocks to ext3_fsblk_t. Convert the
rest of all unsigned long type in-kernel filesystem blocks to ext3_fsblk_t,
and replace the printk format string respondingly.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some of the in-kernel ext3 block variable type are treated as signed 4 bytes
int type, thus limited ext3 filesystem to 8TB (4kblock size based). While
trying to fix them, it seems quite confusing in the ext3 code where some
blocks are filesystem-wide blocks, some are group relative offsets that need
to be signed value (as -1 has special meaning). So it seem saner to define
two types of physical blocks: one is filesystem wide blocks, another is
group-relative blocks. The following patches clarify these two types of
blocks in the ext3 code, and fix the type bugs which limit current 32 bit ext3
filesystem limit to 8TB.
With this series of patches and the percpu counter data type changes in the mm
tree, we are able to extend exts filesystem limit to 16TB.
This work is also a pre-request for the recent >32 bit ext3 work, and makes
the kernel to able to address 48 bit ext3 block a lot easier: Simply redefine
ext3_fsblk_t from unsigned long to sector_t and redefine the format string for
ext3 filesystem block corresponding.
Two RFC with a series patches have been posted to ext2-devel list and have
been reviewed and discussed:
http://marc.theaimsgroup.com/?l=ext2-devel&m=114722190816690&w=2http://marc.theaimsgroup.com/?l=ext2-devel&m=114784919525942&w=2
Patches are tested on both 32 bit machine and 64 bit machine, <8TB ext3 and
>8TB ext3 filesystem(with the latest to be released e2fsprogs-1.39). Tests
includes overnight fsx, tiobench, dbench and fsstress.
This patch:
Defines ext3_fsblk_t and ext3_grpblk_t, and the printk format string for
filesystem wide blocks.
This patch classifies all block group relative blocks, and ext3_fsblk_t blocks
occurs in the same function where used to be confusing before. Also include
kernel bug fixes for filesystem wide in-kernel block variables. There are
some fileystem wide blocks are treated as int/unsigned int type in the kernel
currently, especially in ext3 block allocation and reservation code. This
patch fixed those bugs by converting those variables to ext3_fsblk_t(unsigned
long) type.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was reported as Debian bug #336604.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If ext3 filesystem is larger than 2TB, and sector_t is a u32 (i.e.
CONFIG_LBD not defined in the kernel), the calculation of the disk sector
will overflow. Add check at ext3_fill_super() and ext3_group_extend() to
prevent mount/remount/resize >2TB ext3 filesystem if sector_t size is 4
bytes.
Verified this patch on a 32 bit platform without CONFIG_LBD defined
(sector_t is 32 bits long), mount refuse to mount a 10TB ext3.
Signed-off-by: Mingming Cao<cmm@us.ibm.com>
Acked-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The percpu counter data type are changed in this set of patches to support
more users like ext3 who need more than 32 bit to store the free blocks
total in the filesystem.
- Generic perpcu counters data type changes. The size of the global counter
and local counter were explictly specified using s64 and s32. The global
counter is changed from long to s64, while the local counter is changed from
long to s32, so we could avoid doing 64 bit update in most cases.
- Users of the percpu counters are updated to make use of the new
percpu_counter_init() routine now taking an additional parameter to allow
users to pass the initial value of the global counter.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Steven Rostedt <rostedt@goodmis.org> points out that `rsv' here is usually
NULL, so we should avoid calling kfree().
Also, fix up some nearby whitespace damage.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Give the statfs superblock operation a dentry pointer rather than a superblock
pointer.
This complements the get_sb() patch. That reduced the significance of
sb->s_root, allowing NFS to place a fake root there. However, NFS does
require a dentry to use as a target for the statfs operation. This permits
the root in the vfsmount to be used instead.
linux/mount.h has been added where necessary to make allyesconfig build
successfully.
Interest has also been expressed for use with the FUSE and XFS filesystems.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.infradead.org/~dwmw2/rbtree-2.6:
[RBTREE] Switch rb_colour() et al to en_US spelling of 'color' for consistency
Update UML kernel/physmem.c to use rb_parent() accessor macro
[RBTREE] Update hrtimers to use rb_parent() accessor macro.
[RBTREE] Add explicit alignment to sizeof(long) for struct rb_node.
[RBTREE] Merge colour and parent fields of struct rb_node.
[RBTREE] Remove dead code in rb_erase()
[RBTREE] Update JFFS2 to use rb_parent() accessor macro.
[RBTREE] Update eventpoll.c to use rb_parent() accessor macro.
[RBTREE] Update key.c to use rb_parent() accessor macro.
[RBTREE] Update ext3 to use rb_parent() accessor macro.
[RBTREE] Change rbtree off-tree marking in I/O schedulers.
[RBTREE] Add accessor macros for colour and parent fields of rb_node
From: Andrew Morton <akpm@osdl.org>
Spotted by Jan Capek <jca@sysgo.com>
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Cc: Andreas Dilger <adilger@clusterfs.com>
Cc: Jan Capek <jca@sysgo.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some places in ext3 multiple block allocation code (in 2.6.17-rc3) don't
handle the little endian well. This was resulting in *wrong* block numbers
being assigned to in-memory block variables and then stored on disk
eventually. The following patch has been verified to fix an ext3
filesystem failure when run ltp test on a 64 bit machine.
Signed-off-by; Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All modifications of ->i_flags in inodes that might be visible to
somebody else must be under ->i_mutex. That patch fixes ext3 ioctl()
setting S_APPEND and friends.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sbi->s_group_desc is an array of pointers to buffer_head. memcpy() of
buffer size from address of buffer_head is a bad idea - it will generate
junk in any case, may oops if buffer_head is close to the end of slab
page and next page is not mapped and isn't what was intended there.
IOW, ->b_data is missing in that call. Fortunately, result doesn't go
into the primary on-disk data structures, so only backup ones get crap
written to them; that had allowed this bug to remain unnoticed until
now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for the sys_splice system call. Using a pipe as a
transport, it can connect to files or sockets (latter as output only).
From the splice.c comments:
"splice": joining two ropes together by interweaving their strands.
This is the "extended pipe" functionality, where a pipe is used as
an arbitrary in-memory buffer. Think of a pipe as a small kernel
buffer that you can use to transfer data from one end to the other.
The traditional unix read/write is extended with a "splice()" operation
that transfers data buffers to or from a pipe buffer.
Named by Larry McVoy, original implementation from Linus, extended by
Jens to support splicing to files and fixing the initial implementation
bugs.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a conversion to make the various file_operations structs in fs/
const. Basically a regexp job, with a few manual fixups
The goal is both to increase correctness (harder to accidentally write to
shared datastructures) and reducing the false sharing of cachelines with
things that get dirty in .data (while .rodata is nicely read only and thus
cache clean)
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is no valid reason why we can't support "nobh" option for filesystems
with blocksize != PAGESIZE.
This patch lets them use "nobh" option for writeback mode for blocksize <
pagesize.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mingming Cao recently added multi-block allocation support for ext3,
currently used only by DIO. I added support to map multiple blocks for
mpage_readpages(). This patch add support for ext3_get_block() to deal
with multi-block mapping. Basically it renames ext3_direct_io_get_blocks()
as ext3_get_block().
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Clean up a few little layout things and comments.
- Add a WARN_ON to a case which I was wondering about.
- Tune up some inlines.
Cc: Mingming Cao <cmm@us.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that get_block() can handle mapping multiple disk blocks, no need to have
->get_blocks(). This patch removes fs specific ->get_blocks() added for DIO
and makes it users use get_block() instead.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Optimize the block reservation and the multiple block allocation: with the
knowledge of the total number of blocks ahead, set or adjust the reservation
window size properly (based on the number of blocks needed) before block
allocation happens: if there isn't any reservation yet, make sure the
reservation window equals to or greater than the number of blocks needed,
before create an reservation window; if a reservation window is already
exists, try to extends the window size to match the number of blocks to
allocate. This could increase the possibility of completing multiple blocks
allocation in a single request, as blocks are only allocated in the range of
the inode's reservation window.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update accounting information (quota, boundary checks, free blocks number etc)
in ext3_new_blocks().
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change ext3_try_to_allocate() (called via ext3_new_blocks()) to try to
allocate the requested number of blocks on a best effort basis: After
allocated the first block, it will always attempt to allocate the next few(up
to the requested size and not beyond the reservation window) adjacent blocks
at the same time.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for multiple block allocation in ext3-get-blocks().
Look up the disk block mapping and count the total number of blocks to
allocate, then pass it to ext3_new_block(), where the real block allocation is
performed. Once multiple blocks are allocated, prepare the branch with those
just allocated blocks info and finally splice the whole branch into the block
mapping tree.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently ext3_get_block() only maps or allocates one block at a time. This
is quite inefficient for sequential IO workload.
I have posted a early implements a simply multiple block map and allocation
with current ext3. The basic idea is allocating the 1st block in the existing
way, and attempting to allocate the next adjacent blocks on a best effort
basis. More description about the implementation could be found here:
http://marc.theaimsgroup.com/?l=ext2-devel&m=112162230003522&w=2
The following the latest version of the patch: break the original patch into 5
patches, re-worked some logicals, and fixed some bugs. The break ups are:
[patch 1] Adding map multiple blocks at a time in ext3_get_blocks()
[patch 2] Extend ext3_get_blocks() to support multiple block allocation
[patch 3] Implement multiple block allocation in ext3-try-to-allocate
(called via ext3_new_block()).
[patch 4] Proper accounting updates in ext3_new_blocks()
[patch 5] Adjust reservation window size properly (by the given number
of blocks to allocate) before block allocation to increase the
possibility of allocating multiple blocks in a single call.
Tests done so far includes fsx,tiobench and dbench. The following numbers
collected from Direct IO tests (1G file creation/read) shows the system time
have been greatly reduced (more than 50% on my 8 cpu system) with the patches.
1G file DIO write:
2.6.15 2.6.15+patches
real 0m31.275s 0m31.161s
user 0m0.000s 0m0.000s
sys 0m3.384s 0m0.564s
1G file DIO read:
2.6.15 2.6.15+patches
real 0m30.733s 0m30.624s
user 0m0.000s 0m0.004s
sys 0m0.748s 0m0.380s
Some previous test we did on buffered IO with using multiple blocks allocation
and delayed allocation shows noticeable improvement on throughput and system
time.
This patch:
Add support of mapping multiple blocks in one call.
This is useful for DIO reads and re-writes (where blocks are already
allocated), also is in line with Christoph's proposal of using getblocks() in
mpage_readpage() or mpage_readpages().
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The return value of this function is never used, so let's be honest and
declare it as void.
Some places where invalidatepage returned 0, I have inserted comments
suggesting a BUG_ON.
[akpm@osdl.org: JBD BUG fix]
[akpm@osdl.org: rework for git-nfs]
[akpm@osdl.org: don't go BUG in block_invalidate_page()]
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When EXT3FS_DEBUG is #define-d, the compile breaks due to #include file
issues.
Signed-off-by: Kirk True <kernel@kirkandsheila.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In filesystems with the meta block group flag on, ext3_bg_num_gdb() fails
to report the correct number of blocks used to store the group descriptor
backups in a given group. It happens because meta_bg follows a different
logic from the original ext3 backup placement in groups multiples of 3, 5
and 7.
Signed-off-by: Glauber de Oliveira Costa <glommer@br.ibm.com>
Cc: Andreas Dilger <adilger@clusterfs.com>
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Cc: Alex Tomas <alex@clusterfs.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Under I/O load it may take up to a dozen seconds to read all group
descriptors. This is what ext3_statfs() does. At the same time, we already
maintain global numbers of free inodes/blocks. Why don't we use them instead
of group reading and summing?
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rewrap the overly long source code lines resulting from the previous
patch's addition of the slab cache flag SLAB_MEM_SPREAD. This patch
contains only formatting changes, and no function change.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark file system inode and similar slab caches subject to SLAB_MEM_SPREAD
memory spreading.
If a slab cache is marked SLAB_MEM_SPREAD, then anytime that a task that's
in a cpuset with the 'memory_spread_slab' option enabled goes to allocate
from such a slab cache, the allocations are spread evenly over all the
memory nodes (task->mems_allowed) allowed to that task, instead of favoring
allocation on the node local to the current cpu.
The following inode and similar caches are marked SLAB_MEM_SPREAD:
file cache
==== =====
fs/adfs/super.c adfs_inode_cache
fs/affs/super.c affs_inode_cache
fs/befs/linuxvfs.c befs_inode_cache
fs/bfs/inode.c bfs_inode_cache
fs/block_dev.c bdev_cache
fs/cifs/cifsfs.c cifs_inode_cache
fs/coda/inode.c coda_inode_cache
fs/dquot.c dquot
fs/efs/super.c efs_inode_cache
fs/ext2/super.c ext2_inode_cache
fs/ext2/xattr.c (fs/mbcache.c) ext2_xattr
fs/ext3/super.c ext3_inode_cache
fs/ext3/xattr.c (fs/mbcache.c) ext3_xattr
fs/fat/cache.c fat_cache
fs/fat/inode.c fat_inode_cache
fs/freevxfs/vxfs_super.c vxfs_inode
fs/hpfs/super.c hpfs_inode_cache
fs/isofs/inode.c isofs_inode_cache
fs/jffs/inode-v23.c jffs_fm
fs/jffs2/super.c jffs2_i
fs/jfs/super.c jfs_ip
fs/minix/inode.c minix_inode_cache
fs/ncpfs/inode.c ncp_inode_cache
fs/nfs/direct.c nfs_direct_cache
fs/nfs/inode.c nfs_inode_cache
fs/ntfs/super.c ntfs_big_inode_cache_name
fs/ntfs/super.c ntfs_inode_cache
fs/ocfs2/dlm/dlmfs.c dlmfs_inode_cache
fs/ocfs2/super.c ocfs2_inode_cache
fs/proc/inode.c proc_inode_cache
fs/qnx4/inode.c qnx4_inode_cache
fs/reiserfs/super.c reiser_inode_cache
fs/romfs/inode.c romfs_inode_cache
fs/smbfs/inode.c smb_inode_cache
fs/sysv/inode.c sysv_inode_cache
fs/udf/super.c udf_inode_cache
fs/ufs/super.c ufs_inode_cache
net/socket.c sock_inode_cache
net/sunrpc/rpc_pipe.c rpc_inode_cache
The choice of which slab caches to so mark was quite simple. I marked
those already marked SLAB_RECLAIM_ACCOUNT, except for fs/xfs, dentry_cache,
inode_cache, and buffer_head, which were marked in a previous patch. Even
though SLAB_RECLAIM_ACCOUNT is for a different purpose, it marks the same
potentially large file system i/o related slab caches as we need for memory
spreading.
Given that the rule now becomes "wherever you would have used a
SLAB_RECLAIM_ACCOUNT slab cache flag before (usually the inode cache), use
the SLAB_MEM_SPREAD flag too", this should be easy enough to maintain.
Future file system writers will just copy one of the existing file system
slab cache setups and tend to get it right without thinking.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ext3's truncate_sem is always released in the same function it's taken
and it otherwise is a mutex as well..
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus points out that ext3_readdir's readahead only cuts in when
ext3_readdir() is operating at the very start of the directory. So for large
directories we end up performing no readahead at all and we suck.
So take it all out and use the core VM's page_cache_readahead(). This means
that ext3 directory reads will use all of readahead's dynamic sizing goop.
Note that we're using the directory's filp->f_ra to hold the readahead state,
but readahead is actually being performed against the underlying blockdev's
address_space. Fortunately the readahead code is all set up to handle this.
Tested with printk. It works. I was struggling to find a real workload which
actually cared.
(The patch also exports page_cache_readahead() to GPL modules)
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One can do "chattr +j" on a file to change its journalling mode. Fix
writeback mode with "nobh" handling for it.
Even though, we mount ext3 filesystem in writeback mode with "nobh" option,
some one can do "chattr +j" on a single file to force it to do journalled
mode. In order to do journaling, ext3_block_truncate_page() need to
fallback to default case of creating buffers and adding them to transaction
etc.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes illegal __GFP_FS allocation inside ext3 transaction in
ext3_symlink(). Such allocation may re-enter ext3 code from
try_to_free_pages. But JBD/ext3 code keeps a pointer to current journal
handle in task_struct and, hence, is not reentrable.
This bug led to "Assertion failure in journal_dirty_metadata()" messages.
http://bugzilla.openvz.org/show_bug.cgi?id=115
Signed-off-by: Andrey Savochkin <saw@saw.sw.com.sg>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a code path that passed size to ext2_xattr_set
(ext3_xattr_set_handle) before initializing it. The callees don't use the
value in that case, but gcc cannot tell. Always initialize size to get rid
of the warnings.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Migrate a page with buffers without requiring writeback
This introduces a new address space operation migratepage() that may be used
by a filesystem to implement its own version of page migration.
A version is provided that migrates buffers attached to pages. Some
filesystems (ext2, ext3, xfs) are modified to utilize this feature.
The swapper address space operation are modified so that a regular
migrate_page() will occur for anonymous pages without writeback (migrate_pages
forces every anonymous page to have a swap entry).
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove redundant NULL check in ext3_lookup() as d_splice_alias() can take NULL
inode as input.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
fs: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- there's no need for ext3_count_free() #ifndef EXT3FS_DEBUG
- having prototypes for ext3_count_free() in two different headers is
nonsense
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Christoph Hellwig <hch@lst.de>
remove checks now in the VFS
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the superblock-lock semaphore to a mutex, affecting
lock_super()/unlock_super(). Tested on ext3 and XFS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are places in the resize code in which EXT3_SB() macro is used after
an statement like sbi = EXT3_SB(sb) is done. Inside the same function,
both sbi and EXT3_SB() are used to reference the super block Altough it is
not wrong, keeping it coherent increases legibility, IMHO.
Signed-off-by: Glauber de Oliveira Costa <glommer@br.ibm.com>
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Cc: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
