Add workaround for a hardware interrupt issue. When using INTA,
unmasking of the interrupt and the tag update should be done
separately to avoid some spurious interrupts,
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix TCP/UDP checksum verification. Use status bits in the buffer
descriptor instead of the checksum value to verify rx checksum.
Using the checksum value will be incorrect if the UDP packet has
zero in the UDP checksum field.
Firmware update required for this fix.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some misc. fixes for WoL, 5708 B1, and a typo '=' instead of '=='.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve handshake with bootcode with the following changes:
1. Increase timeout to 100msec and use msleep instead of udelay.
2. Add more error checking for timeouts and errors.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always set up the device to strip incoming VLAN tags when ASF is
enabled. ASF firmware will not parse packets correctly if VLAN tags
are not stripped.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the superfluous parameter checking in bnx2_{get,set}_eeprom.
The parameters are already validated in ethtool_{get,set}_eeprom.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return of dev_alloc_skb in bnx2_test_loopback, and handle
appropriately.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output driver name as prefix to "Unknown flash/EEPROM type." message.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refine bnx2_poll() logic to write back the most up-to-date status tag
when all work has been processed. This eliminates some occasional
extra interrupts when a older status tag is written even though all
work has been processed.
The idea is to read the status tag just before exiting bnx2_poll() and
then check again for any new work. If no new work is pending, the
status tag written back will not generate any extra interrupt. This
logic is similar to the changes David Miller did to tg3_poll().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dynamically determine the shared memory location where eeprom
parameters are stored instead of using a fixed location.
Add speed reporting to management firmware. This allows management
firmware to know the current speed without contending for MII
registers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update bnx2 nvram code with support for 5708.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 5708 copper and serdes basic support, including 2.5 Gbps support
on 5708 serdes. SPEED_2500 is also added to ethtool.h
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bug in bnx2_interrupt() that caused an unnecessary register read.
The BNX2_PCICFG_MISC_STATUS should only be read when the status tag
has not changed.
Add prefetch of the status block in bnx2_msi() similar to tg3_msi().
The status block is not touched in bnx2_msi() and prefetching it will
speed up bnx2_poll() that will run on the same CPU that received the
MSI.
Update version.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update version and add 4 minor fixes, the last 2 were suggested by
Jeff Garzik:
1. check for a valid ethernet address before setting it
2. zero out bp->regview if init_one encounters an error and unmaps
the IO address. This prevents remove_one from unmapping again.
3. use netif_rx_schedule() instead of hand coding the same.
4. use IRQ_HANDLED and IRQ_NONE.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all locks from spin_lock_irqsave() to spin_lock_bh(). All
places that require spinlocks are in BH context.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove atomic operations in the fast tx path. Expensive atomic
operations were used to keep track of the number of available tx
descriptors. The new code uses the difference between the consumer
and producer index to determine the number of free tx descriptors.
As suggested by Jeff Garzik, the name of the inline function is
changed to all lower case.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This speeds up link-up time on 5706 SerDes if the link partner does
not autoneg, a rather common scenario in blade servers. Some blade
servers use IPMI for keyboard input and it's important to minimize
link disruptions.
The speedup is achieved by shortening the timer to (HZ / 3) during
the transient period right after initiating a SerDes autoneg. If
autoneg does not complete, parallel detect can be done sooner. After
the transient period is over, the timer goes back to its normal HZ
interval.
As suggested by Jeff Garzik, the timer initialization is moved to
bnx2_init_board() from bnx2_open().
An eeprom bit is also added to allow default forced SerDes speed for
even faster link-up time.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an rtnl deadlock problem when flush_scheduled_work() is
called from bnx2_close(). In rare cases, linkwatch_event() may be on
the workqueue from a previous close of a different device and it will
try to get the rtnl lock which is already held by dev_close().
The fix is to set a flag if we are in the reset task which is run
from the workqueue. bnx2_close() will loop until the flag is cleared.
As suggested by Jeff Garzik, the loop is changed to call msleep(1)
instead of yield() in the original patch.
flush_scheduled_work() is also moved to bnx2_remove_one() before the
netdev is freed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following possible cleanups/fixes:
- use C99 struct initializers
- make a few arrays and structs static
- remove a few uses of literal 0 as NULL pointer
- use convenience function instead of cast+dereference in bnx2_ioctl()
- remove superfluous casts to u8 * in calls to readl/writel
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new driver bnx2 for Broadcom bcm5706 is available.
The patch also includes new 1000BASE-X advertisement bit definitions in
mii.h
Thanks to David Miller and Jeff Garzik for reviewing and their valuable
feedback.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
