there is endianness issue both Tx and Rx.
Currently, data is set like below.
Register:
MSB--LSB
x x D0 D1
x x D2 D3
x x D4 D5
x x D6 D7
But Data to be sent must be set like below.
Register:
MSB--LSB
x x D1 D0
x x D3 D2
x x D5 D4
x x D7 D6 (x means reserved area.)
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To easy to read/understand, divide poll function into two sub-functions.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is no flow control processing.
Thus, Add flow control processing as
when there is no empty of tx buffer,
netif_stop_queue is called.
When there is empty buffer, netif_wake_queue is called.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6175ddf06b changes the way
memcpy_toio() works for x86_64, causing firmware loading to fail for
some Ralink WLAN devices with the rt2800pci driver since linux 2.6.34.
This causes the log message: "phy0 -> rt2800pci_load_firmware: Error -
PBF system register not ready.".
Fix this by using __iowrite32_copy instead of memcpy_toio().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pad beacon to a multiple of 32 bits in preparation for the change
from memcpy_toio() to __iowrite32_copy() in register_multiwrite().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stray semicolon after DEBUG_PRINTK_MSG causes things
like "if (...) WARNING(...); else {}" to fail with syntax error.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Queue names were incorrectly copied from the legacy drivers,
as a result the queue names were inversed to what was expected.
This renames the queues using this mapping:
QID_AC_BK -> QID_AC_VO (priority 0)
QID_AC_BE -> QID_AC_VI (priority 1)
QID_AC_VI -> QID_AC_BE (priority 2)
QID_AC_VO -> QID_AC_BK (priority 3)
Note that this was a naming problem only, which didn't affect
the assignment of frames to their respective queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a queue entry flag ENTRY_DATA_STATUS_PENDING,
which can be used to indicate a queue entry has
returned from the hardware and is waiting for
status processing. Using this flag we can add
some extra sanity checks to prevent queue corruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the rt2x00_dmastart function to rt2x00lib which
marks the queue_entry as "owned by device", and increased
the Q_INDEX number.
This cleanups up the index handling by rt2x00lib which
at until so far used hackish approaches to keep the
RX queue index numbering sane.
The rt2x00pci.c changes are from Helmut Schaa
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new command to the queue handlers: "flush",
this moves the flush() callback from mac80211
into rt2x00queue and adds support for flushing
the RX queue as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add wrapper functions in rt2x00queue.c to
start & stop queues. This control must be protected
using a mutex.
Queues can also be paused which will halt the flow
of packets between the driver and mac80211. This doesn't
require a mutex protection.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, change the queue callback
function names to have 3 different actions: start, kick & stop.
We can now also remove the STATE_RADIO_RX_ON/STATE_RADIO_RX_OFF
device_state flags, and replace the usage with using the
start_queue/stop_queue callback functions.
This streamlines the RX queue handling to the
similar approach as all other queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, we now introduce
3 queue commands: start, kick, stop.
- Start: will enable a queue, for TX this will
not mean anything, while for beacons and RX
this will update the registers to enable the queue.
- Kick: This will kick all pending frames to
the hardware. This is needed for the TX queue
to push all frames to the HW after the queue
has been started
- Stop: This will stop the queue in the hardware,
and cancel any pending work (So this doesn't
mean the queue is empty after a stop!).
Move all code from the drivers into the appropriate
functions, and link those calls to the old rt2x00lib
callback functions (we will fix this later when we
refactor the queue control inside rt2x00lib).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0204464329 "Check for specific changed
flags when updating the erp config" changed the way in which a new beacon
interval gets handled. However, due to a bug in rt2800usb and rt2800pci the
beacon interval was reset during each scan, thus causing problems in AdHoc
mode.
Fix this by not cleaning up the beacon interval when killing the beacon queue
but just prevent the device from sending out beacons.
Reported-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes to the TX-done code of rt2x00 resulted in TX-ed frames not
being returned to mac80211 in the original state, and therefore with
insufficient headroom for re-transmissions.
Fix this by reverting the changes done and by ensuring we remove the inserted
L2pad by moving the header backwards instead of the data forwards.
At the same time also make sure that the rt2x00queue_remove_l2pad will not
move any memory when a frame has no data at all.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Jay Hung <Jay_Hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an rt2x00 USB device is unplugged while in use, it reliably
hangs the whole system. After some time the watchdog prints:
BUG: soft lockup - CPU#0 stuck for 64s! [kworker/u:0:5]
...
[<c01a88d8>] (usb_submit_urb+0x0/0x2ac) from [<bf0e752c>] (rt2x00usb_kick_rx_entry+0xb4/0xe8 [rt2x00usb])
[<bf0e7478>] (rt2x00usb_kick_rx_entry+0x0/0xe8 [rt2x00usb]) from [<bf0e7588>] (rt2x00usb_clear_entry+x28/0x2c [rt2x00usb])
[<bf0e7560>] (rt2x00usb_clear_entry+0x0/0x2c [rt2x00usb]) from [<bf0d5bc4>] (rt2x00lib_rxdone+0x2e0/0x2f8 [rt2x00lib])
[<bf0d58e4>] (rt2x00lib_rxdone+0x0/0x2f8 [rt2x00lib]) from [<bf0e7e00>] (rt2x00usb_work_rxdone+0x54/0x74 [rt2x00usb])
[<bf0e7dac>] (rt2x00usb_work_rxdone+0x0/0x74 [rt2x00usb]) from [<c00542b4>] (process_one_work+0x20c/0x35c)
Clear the DEVICE_STATE_PRESENT flag when usb_submit_urb()
returns -ENODEV to fix this.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RF chip definition
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_survey callback to allow user space to read statistics
about the current channel condition.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add and modify NIC Configuration and LED definition of EEPROM
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the likelihood of false pulse detects in the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM PAPRD rate mask fields only contain mask values for actual
rates in the low 25 bits. The upper bits are reserved for tx power
scale values. Add the proper mask definitions and use them before
writing the values to the register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to measure the thermal values correctly for PAPRD, we need
to send training frames before setting up the gain table for the measurement,
and then again afterwards for the actual training.
For further improvement, send training frames at MCS0 instead of 54 MBit/s
legacy. That way we can use the No-ACK flag for the transmission, which
speeds up PAPRD training in general, as the hardware won't have to
retransmit and wait for ACK timeout (was previously set to 4 * 6
transmission attempts).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testing shows that adjusting the slot time based on the coverage class
produces very high latencies and very low throughput on long distance links.
Adjusting only the ACK timeout and leaving the slot time at the regular
values - while technically not optimal for CSMA - works a lot better on
long links (tested with 10 km distance)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(u32) -1 is not particularly useful as a slottime default, so even though
the ath9k_hw default should never get used, it's better to pick something
sane here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have separate callbacks for pre-AR9003 vs AR9003
SREV version checks, so just merge those into one function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 based hardware with 3 antennas and slow antenna diversity has
not been seen in the wild and ath9k does not support that form of
antenna diversity, so remove the EEPROM ops for it.
These EEPROM ops are currently only used for setting the
AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific
file already.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a comment about a potential array overrun that needs to
be reviewed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer chips do not need this, and maybe these register writes could have
negative side effects on newer hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless-testing commit 04caf86375
('ath9k: more tx setup cleanups') merged tx path code for HT vs
non-HT frames, however it did not pass the tid pointer to
ath_tx_send_normal, causing an inconsistency between AMPDU vs
non-AMPDU sequence number handling.
Fix this by always passing in the tid pointer for all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When software crypto is used, mac80211 will
support IBSS RSN, it doesn't depend on the
driver in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when accessing registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WMM IE QoS Info field lower 4 bits: Parameter Set Count
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 802.11 spec states that the STA that generated the last Beacon frame shall
be the STA that response to a probe request. This is important for congestion
reduction when a probe request is received - only 1 node in an adhoc BSS
will transmit a response. While mac80211 drivers should provide the
tx_last_beacon function to report if they transmitted the last beacon many
do not. As an attempt to reduce probe response congestion default this
to 0 such that a node not implementing this capability does not contribute
to unnecessary congestion.
In a modern medium sized office environment I see upwards of 100 probe
requests per second received at a given node from various hardware/OS/drivers
doing zeroconf 'active probing' as opposed to passively listening for beacons.
With a modest 10-node adhoc network consisting of drivers that do not implement
this tx_last_beacon feature, I have seen this result in the simultaneous xmit
of probe responses accumulating to 500 probe responses per second because of
collisions which brings the adhoc network to its knees as well as causes
needless congestion.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed we do not know band width at core reset time and it is not a good
idea to reset whole just to change band. So just set unconditionally 20 MHz
band width as default during core reset.
As for defines PHY clock changed to band width in specs and it makes much more
sens to call defines by band width which is self-explainable. Updated specs do
not mention 0 value, but comparing to old ones you can notice lineral relation
between PHY clock speed and band width. So it makes sense for 0x0 value to be
10 MHz band width.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for split default keys (unicast
and multicast) in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the default key for "any key set" isn't
quite what we should do. It works, but with the
upcoming changes it makes life unnecessarily
complex, so do something better here and really
check for "any key".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers TBTT_TIMER ,DMA_BEACON_ALERT ,NEXT_SWBA are need to be
configured only for AP and IBSS mode.
SWBA register is used for generating software interrupts so that beacon
frames will be created by the software.DMA beacon alert register is
to indicate the hardware to DMA the contents of beacon buffer to PCU buffer
and TBTT to start transmitting the packet buffer to the base band.
Clearly these things are not needed for station/monitor mode so
remove configuring them.
Cc: doug dahlby <ddahlby@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a cached BSS struct is updated because a new beacon was received,
the code replaces the cached information elements by the IEs from the
new beacon. However it did not update the pub.information_elements
and pub.len_information_elements fields leaving them either pointing
to the old beacon IEs or in an inconsistent state where the data is
replaced by the new beacon IEs but len_information_elements still has
its value from the first beacon.
Fix this by updating the information elements fields if they are
pointing to beacon IEs.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
