Add 3630SDP board support
The board shares the same peripherals as a zoom2 main.
So reuse the peripheral file of zoom platform.
Peripheral zoom2 zoom3 sdp3630
---------------------------------------
Ethernet smsc smsc smc
NOR n/a n/a B
Onenand n/a n/a B
HDMI A A B (persent on different i2c)
NAND A A A (same nand)
SDRAM A A A (same sdram)
Keypad A A A (same twl)
Camera A A A (same sensor can be mounted)
LCD Display A A A (same wvga display)
OPPs A A A (same chip feature)
Audio A A A (same audio via twl5030)
OMAP3630 details can be found here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds basic support for CompuLab CM-T35 module.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Neuros OSD 2.0 is the hardware component of the Neuros Open
Internet Television Platform. Hardware is very close to Ti DM644X-EVM board.
It has: DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC,
USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video.
Additionaly realtime clock, IR remote control receiver,
IR Blaster based on MSP430 (firmware although is different
from used in DM644X-EVM), internal ATA-6 3.5” HDD drive
with PATA interface, two muxed red-green leds.
For more information please refer to
http://wiki.neurostechnology.com/index.php/OSD_2.0_HD
Signed-off-by: Andrey Porodko <panda@chelcom.ru>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes the following warning:
arch/arm/mach-davinci/board-sffsdr.c:99: warning: 'sffsdr_emac_pdata' defined but not used
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
A section mismatch is reported for gpio_led_platform_data
as it is referenced by a non annotated function (evm_led_setup)
This patch fixes the issue by converting the __initconst to const
as is the case in arch/arm/mach-davinci/board-dm644x-evm.c file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Include high speed capabilities in MMC/SD platform data
for DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Using a device_initcall() for initializing the voltage regulator
on DA850 is not such a good idea because it gets called for all
platforms - even those who do not have a regulator implemented.
This leads to a big fat warning message during boot-up when
regulator cannot be found.
Instead, tie initialization of voltage regulator to cpufreq init.
Define a platform specific init call which in case of DA850 gets
used for initializing the regulator. On other future platforms it
can be used for other purposes.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch provides a function to help register cpuidle driver
on da8xx/omap-l1xx platforms.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch adds support for DaVinci cpu idle driver.
Two idle states are defined:
1. Wait for interrupt
2. Wait for interrupt and DDR self-refresh (or power down)
Some DaVinci SoCs support putting DDR in self-refresh (eg Dm644x, DM6467)
while others support putting DDR in self-refresh and power down (eg DM35x,
DA8xx).
Putting DDR (or mDDR) in power down saves more power than self-refresh.
The patch has been tested on DA850/OMAP-L138 EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When kernel is built with CONFIG_DEBUG_SECTION_MISMATCH=y
option, using da8xx_omapl_defconfig, some warnings are
observed:
WARNING: vmlinux.o(.text+0xc2a4): Section mismatch in reference
from the function da850_evm_setup_nor_nand() to the variable
.init.data:da850_nand_pins
The function da850_evm_setup_nor_nand() references
the variable __initdata da850_nand_pins.
This is often because da850_evm_setup_nor_nand lacks a __initdata
annotation or the annotation of da850_nand_pins is wrong.
This patch fixes such warnings.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Eliminate the static function declaration by rearranging
data in da850/omap-l138 board file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are multiple steps in configuring the EMAC to MII or RMII mode.
Current code implements them using multiple checks.
Consolidate the multiple checks into a single if construct.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Get rid of DA850_UI_EXP config option since it is not used anywhere
else in code.
Instead make the UI expander choice menu dependent on the EVM
selection itself.
Also add help text indicating that UI board is actually detected
automatically.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Implement autodetection of RMII PHY by shifting the decision
to use the RMII PHY to da850_evm_ui_expander_setup() from
da850_evm_init() earlier.
Without this patch, selecting RMII PHY in the UI expander menu
will make the MII PHY unusable even though UI board is not
connected.
The actual configuration and registration of the EMAC device
is delayed to device_initcall() so it happens after the UI card
detection is complete.
A side effect of this patch is the removal of a voilation of
Documentation/SubmittingPatches section 2.2 in function
da850_evm_init()
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On the DA830, AEMIF and MMC/SD pins are shared. On the EVM, when
the mux_mode signal is low MMC/SD works and when mux_mode signal
is high, NAND works.
When MMC/SD driver is configured in the kernel, do not let NAND
get registered and drive mux_mode high. Instead, print a warning
for user to understand why the platform device for NAND did not
get registered.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch supports runtime detection of DA830 UI card and
eliminates the need for DA830_UI config option. Successful
probe of GPIO expander present on the UI card is used to
detect its presence. For this reason, GPIO_PCF857X is auto-
selected when DA830 EVM is configured. In case the UI card
is absent, the probe fails in reasonable time.
As a side effect this patch also gets rid of the voilation
of Documentation/SubmittingPatches section 2.2 in function
da830_evm_ui_expander_setup()
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove ifdefs inside da830_evm_init function since they are
discouraged in Documentation/SubmittingPatches section 2.2
Use the method outlined in that document for fixing it.
Tested on DA830 EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes the following warning seen when building with default
config:
arch/arm/mach-davinci/board-da830-evm.c:371: warning: 'da830_evm_devices' defined but not used
Tested on DA830 EVM with and without CONFIG_DA830_UI_NAND enabled.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for NAND flash parts on the DA830/OMAP-L137 EVM
User Interface board. This includes overriding the default
bad block tables used by the davinci_nand driver.
Signed-off-by: David A. Griego <dgriego@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Properly set up the OTG mode thru the CFGCHIP2 register, enable the
USB0_DRVVBUS pin, and finally register the MUSB platform device.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the function to register the MUSB platform device.
Additional compile warning fixes by Sekhar Nori.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename setup_usb() into davinci_setup_usb(). While at it:
- move its declaration from <mach/common.h> to more fitting <mach/usb.h>;
- teach it to handle values of the 'mA' parameter greater than 510 and thus
pass 1000 instead of 500 for the power switches capable of sourcing over 1 A;
- teach it to handle odd values of the 'potpgt_ms' parameter...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
DMx:
- enable MMC and dm365evm_keys
- Enable DM355 and DM365 input drivers as modules.
da8xx
- combine da830 and da850 into common defconfig
- drop SYSFS_DEPRECATED flag
- auto-select D$ writethrough for da830
- enable CPUfreq and FB
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In the McASP clock definition add a flag to indicate that the peripheral clock
belongs to ASYNC3 clock domain.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data and partition info for NAND on dm6467 EVM.
Note that the partition layout is dependent on the UBL, U-Boot etc. used. This
patch tries to minimize that dependency by setting first partition for UBL,
U-Boot and environment altogether.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There have accumulated quite a lot of them after the code reorganizations...
In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes it easier to identify SoC init failures
by panicing when SoC init fails. Without successful SoC
init, the kernel eventually fails when attempt is made to
access the clocks.
Also, an error is printed when JTAG ID match fails to make
it easier to identify failures due to SoC rev changes.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY
is enabled by proper programming of the IO Expander (TCA6416) ports. Also for
RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the
PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds
support for RMII PHY.
This patch also adds a menuconfig option to select one or no peripheral
connected to expander. Currently, sub-options in this menu are RMII and no
peripheral.This menuconfig option is similar to the one present for UI card on
DA830/OMAP-L137 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM can be connected to an UI card which has various
peripherals on it.The UI card has TCA6416 expander which can be probed
to check whether the UI card is connected or not. If the UI card is
connected, setup NOR and NAND devices. This is done via the expander
setup callback.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Replace badly chosen 'psc_ctlr' name of the 'struct clk' field (PSC already
means "Power and Sleep Controller", so the '_ctlr' postfix makes the name
tautological) with technically correct 'gpsc' (Global PSC -- which contains
all the module registers).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for using the TPS65070 PMIC found
on the DA850/OMAP-L138 EVM.
It defines the power rail consumer mapping and registers the
the I2C based PMIC as a board device.
The power rail constraints are derived from the maxmimum and
minimum recommended operating condition values of the respective
consumers derived from section 5.2 of the OMAP-L138 datasheet.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for regulating the CVDD voltage for the
DA850/OMAP-L138 platform.
The CVDD min and max values for each OPP have been obtained from
section 5.2 "Recommended Operating Conditions" of SPRS586
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds basic frequency scaling support for DA850/OMAP-L138.
Currently, frequency scaling only on PLL0 is supported. No scaling of PLL1
as yet.
Peripherals like MMC/SD which have a clock input synchronous with
ARM clock will not work well since the clock will change behind their backs.
Support for notification to such devices to adjust themselves to the
new frequency will be added in later patches. Current defconfigs keep
CPUFreq disabled so it will not affect normal operation.
The OPP defintions assume clock input of 24MHz to the SoC. This is inline
with hardcoding of input frequency in the <soc>.c files. At some point
this will need to move into board dependent code as new boards appear with
a different reference clock.
Tested on OMAP-L138 EVM with ondemand governer and a shell script to
vary processor load.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a basic CPUFreq driver for DaVinci devices registering with the
kernel CPUFreq infrastructure.
Support is added for both frequency and voltage regulation.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Newer revs of da830 silicon have different 'variant' field of the JTAG
id register. Current code only supports rev 1.0 silicon.
This patch adds support for rev1.1 and rev2.0 silicon and updates
the 'name' strings to add a '-' between 'omap' & 'l137' to have
consistent naming with da850/omap-l138.
From Mark Grosen <mgrosen@ti.com>:
"There are currently three silicon revisions for OMAPL137. The JTAG IDs
(DEVIDR register contents) for each silicon revision are shown below:
0x0B7D F02F for silicon revision 1.0
0x8B7D F02F for silicon revision 1.1
0x9B7D F02F for silicon revision 2.0
Corresponding errata documentation will be available in the next few
weeks on the ti.com website."
Reported-by: Nick Thompson <Nick.Thompson@gefanuc.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The machine name string shows up in /proc/cpuinfo under 'Hardware' and
can be used by userspace apps. Make the format consistent with the
DA850/OMAP-l138 EVM by adding the '-' between OMAP and L137.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On this board the OHCI port's power control and over-current signals from
TPS2065 power switch are connected via GPIO1[15] and GPIO2[1] respectively,
so we can implement the DA8xx OHCI glue layer's hooks for overriding the
root hub port's power and over-current status bits.
We also have to properly set up the clocking mode in the CFGCHIP2 register,
so that internal 24 MHz reference clock is fed to the USB 2.0 (MUSB) PHY and
its output is used to clock the USB 1.1 (OHCI) PHY...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the function to register the OHCI platform device, given the root hub
related platform data passed from the board specific code. The platfrom
data provide for overriding the OHCI port power and over-current bits at
the board level.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
These are needed by the MUSB and OHCI glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch itself does not change the functionality of
any existing code. PARAM entries in the present GIT kernel
are referred to as slots. New API's being added to the
EDMA driver were referring to these PARAM entries as
"params". This patch updates the terminolgy used in the
EDMA driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The reserve_contiguous_params function is used to reserve
a set of contiguous PARAMs. If we do not find a complete
set of contiguous PARAMs, the functions still has to free
every PARAM that it found to be free in the process of finding a
complete set and thus marked as "in use".
This patch mainly deals with correctly handling the
freeing of PARAMs.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch updates the NAND driver platform data to use 4-bit ECC and the
ECC_HW/ECC_HW_OOB_FIRST modes.
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch updates the NAND driver platform data to use 4-bit ECC and the
ECC_HW/ECC_HW_OOB_FIRST modes.
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The edma_alloc_cont_slots API is used for obtaining a set of
contiguous slots. When we use the "_ANY" option with this
API, by definition of this option it is suppossed to start
looking for a set of contiguous slots starting from slot 64 for
DaVinci SOC's and 32 for DA8xx SOC's. This has been explained in
the API description in the driver itself. So when we use the
"_ANY" option with this API, the slot number passed as
an argument should be a "don't care".
This patch takes care of this condition mentioned above.
When checking to see if the starting slot is a valid number,
it checks to make sure that the "_ANY" option is not used.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In the edma_free_cont_slots API, the variable slot was being modified
and then used in the for loop.
This results in incorrect behaviour when the API is used.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin
number of LCD panel power has changed. This patch takes
care of this change. Software will support only Beta
versions of DA850/OMAP-L138 EVM.
In the process, add the missing entry for data pin 0
and remove the GPIO specific pins from da850_lcdcntl_pins
structure. EVM specific muxing for LCD is being done in the
board file now.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add RTC support for the da830/omap-l137 and da850/omap-l138
SoC's by leveraging existing the rtc-omap driver.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add graphics support for the Sharp LCD035Q3DG01 graphical
LCD that's on the User Interface (UI) daughter card of the
DA830/OMAP-L137 EVM.
The LCD shares EMIFA lines with the NAND and NOR devices that
are also on the UI card so those lines are shared via a couple
of muxes. The muxes are controlled by the 'MUX_MODE' line on
the UI card. The 'MUX_MODE' line is controlled by pin P6 of
a pcf8574 i2c expander that's at i2c address 0x3f on UI card.
The i2c expander is controlled using the gpio infrastructure
from the board code using the 'setup()' and 'teardown()'
routines.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the Sharp LCD035Q3DG01 graphical LCD. This
requires a minor interface change to da8xx_register_lcdc()
so that the board code can pass in the platform_data which
describes the lcd controller that's to be used.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add pinmux settings, etc. to enable the MMC/SC hardware.
Signed-off-by: David A. Griego <dgriego@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM6467 silicon revisions 3.x have variant field in JTAGID register as '1'.
This path adds entry for the same in dm646x_ids to be able to boot on boards
with 3.x revision chips.
Also modifies name for 'variant=0' (revisions 1.0, 1.1).
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch allows Async3 clock source to be selected between PLL1 SYSCLK2
and PLL0 SYSCLK2.
Having Async3 source from PLL1 SYSCLK2 allows peripherals on that
domain to remain unaffected by frequency scaling on PLL0.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The clk_set_parent() API is implemented to enable re-parenting
clocks in the clock tree.
This is useful in DVFS and helps by shifting clocks to an asynchronous
domain where supported by hardware
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
clk_round_rate, clk_set_rate have been updated to handle dynamic
frequency changes.
The motivation behind the changes is to support dynamic CPU frequency
change.
davinci_set_pllrate() changes the PLL rate of a given PLL. This function
has been presented as a generic function though it has been tested only
on OMAP-L138 EVM. No other currently available DaVinci device will probably
use this function, but any future device specific changes will hopefully be
small enough to get taken care using a cpu_is_xxx() macro.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Make clock rate recalculation easy by having a re-calculate
function for each clock.
The existing functions for calculation of output rates of PLL
and PLL-derived sysclks have been convered to the new
re-calculate API.
A new function is introduced to take care of rate
(re)calculation for leaf clocks.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Achieve easy top down traversal of clock tree by keeping
track of each clock's list of children.
This is useful in supporting DVFS where clock rates of
all children need to be updated in an efficient manner.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This makes it clear that JTAG ID register is part of the
SYSCFG module
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Avoid use of IO_ADDRESS() for SYSCFG module by doing an ioremap() instead.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename the DA8XX_BOOT_CFG_BASE macro to get it in line
with the public documentation for these parts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The DA830/OMAP-L137 EVM cannot use the default pinmux setup for McASP1
so put the correct settings in the board file for that platform.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For consistency with existing code, change the name of
da8xx_init_mcasp() to da8xx_register_mcasp().
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Some mcasp code was inserted between the emac resource setup
and the related register routine that registers the emac.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
1) Registers the platform device for McBSP on dm365.
2) Add platform data to DM365 EVM board file.
3) Set i2c address for audio codec at DM365 EVM board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The parent clock for the USB source clock is actually PLL1 aux clock,
not PLL2 sysclk1.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes a typo/bug in the DM365 SDIO interrupt assignment
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On ARMv7, it is invalid to map the same physical address multiple times
with different memory types. Since system RAM is already mapped as
'memory', subsequent remapping of it must retain this attribute.
However, DMA memory maps it as "strongly ordered". Fix this by introducing
'pgprot_dmacoherent()' which provides the necessary page table bits for
DMA mappings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
It's unnecessary; x86 doesn't do it, and ALSA doesn't require it
anymore.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
This entirely separates the DMA coherent buffer remapping code from
the allocation code, and gets rid of the duplicate copy in the !MMU
section.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
IXP23xx added support for dma_alloc_coherent() for DMA arches with an
exception in dma_alloc_coherent(). This is a subset of what goes on
in __dma_alloc(), and there is no reason why dma_alloc_writecombine()
should not be given the same treatment (except, maybe, that IXP23xx
doesn't use it.)
We can better deal with this by moving the arch_is_coherent() test
inside __dma_alloc() and killing the code duplication.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
No point wrapping the contents of this function with #ifdef CONFIG_MMU
when we can place it and the core_initcall() entirely within the
existing conditional block.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
We effectively have three implementations of dma_free_coherent() mixed up
in the code; the incoherent MMU, coherent MMU and noMMU versions.
The coherent MMU and noMMU versions are actually functionally identical.
The incoherent MMU version is almost the same, but with the additional
step of unmapping the secondary mapping.
Separate out this additional step into __dma_free_remap() and simplify
the resulting dma_free_coherent() code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
The nommu version of dma_alloc_coherent was using kmalloc/kfree to manage
the memory. dma_alloc_coherent() is expected to work with a granularity
of a page, so this is wrong. Fix it by using the helper functions now
provided.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
The coherent architecture dma_alloc_coherent was using kmalloc/kfree to
manage the memory. dma_alloc_coherent() is expected to work with a
granularity of a page, so this is wrong. Fix it by using the helper
functions now provided.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Samsung S5PC1xx SoCs are based on ARM Coretex8, which has 64 bytes of L1
cache line size. Enable proper handling of L1 cache on these SoCs.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Just for the sake of consistency across the ep93xx-tree.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Just for the sake of consistency across the ep93xx-tree.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the core support needed by the ep93xx matrix keypad driver.
The keypad driver unfortunately was merged early and the core
support is missing. The clkdev support has been resolved and
is now merged. This adds the platform device to the ep93xx
core and supplies the functions needed to acquire/free the gpio
pins and actually enable/disable the controller peripheral.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is useful for audio where we do not want to setup a new scatterlist
after playing 4GB of audio data. This would cause skips in the playback.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current model does not allow to put a pad into different modes
once a pins is allocated. Remove the resource handling.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds requirement for ADC on mc13783 and moves the spidev declaration
to marxbot file.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is mostly a straightforward translation. The primary side
effect to the resulting vmlinux should be to increase the alignment on
the initramfs to the standard PAGE_SIZE from 32 bytes.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This has the consequence of changing the section name used for head
code from ".text.head" to ".head.text". Since this commit changes all
users in the architecture, this change should be harmless.
The .text.head output section is eliminated and the head text code is
included at the start of the .init output section.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using OABI, the call to put_user in do_signal can fail causing the
calling app to hang.
The solution is to check if put_user fails and force the app to
seg fault in that case.
Tested with multiple sleeping apps/threads (using the nanosleep syscall)
and suspend/resume.
Signed-off-by: janboe <janboe.ye at gmail.com>
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We will need to treat dma_unmap_page() differently from dma_unmap_single()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-By: Jamie Iles <jamie@jamieiles.com>
The non-highmem() and the __pfn_to_bus() based page_to_dma() both
compile to the same code, so its pointless having these two different
approaches. Use the __pfn_to_bus() based version.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-By: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
The macro mx31_revision() used to take the global variable system_rev to
determine the CPU revision number. However, this number is expected to
be set by the bootloader and is usually zero (at least on my MX31 based
boards here). More than that, it is usually taken to identify the
board's revision, not the CPU's.
Fix that by reading the the CPU's SREV register instead.
Right now, mx31_read_cpu_rev() is called from mx31_clocks_init() which
is admittedly not a good place for it. However, we need to enable the
IIM clock first, and the clock code also has conditional code that
depends on mx31_revision() returning the right thing.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
wl1251 is connected to the SPI bus in rx51, add support for this.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds board specific SDRAM init for RX51. This patch is a
collaboration of work from following people:
Juha Yrjola: Original code
Lauri Leukkunen: Port to RX51
Tero Kristo: Support for multiple OPP:s, merge of patches
Samu Onkalo: Fixed SDRAM parameters according to specs
Kalle Jokiniemi: A fix for rounding error
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Cc: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a new defconfig for the HTC Herald series of devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch introduces support for the HTC Herald (T-Mobile
Wing, etc.) series of smart phones -- board support and LCD
panel settings.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update DEBUG_LL for zoom2 board as CONFIG_OMAP_LL_DEBUG_NONE
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C-1 bus frequency on zoom2/zoom3/sdp3630 should be 2.4 MHz.
The speed is limited by TWL5030/GAIA; a higher speed could lead to errors
on the interface.
The maximum I2C speed depends on the system clock for GAIA:
2.2 MHz (sys-clk = 19.2 MHz)
2.4 MHz (sys-clk = 26 MHz)
2.9 MHz (sys-clk = 38.4 MHz)
For Zoom2/Zoom3/SDP3630 the system clock is 26Mhz
and hence choose 2.4Mhz for I2C1 bus speed
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace zoom2 with zoom name in board-zoom-peripherals.c file
and board-zoom-debugboard.c. Create mach/board-zoom.h.
This file has functions reused for boards: Zoom2/Zoom3/sdp3630.
Hence have all functions commonly named as zoom
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Split zoom2 board file into a base board file and a board-zoom-peripherals.c
file. That way the same peripherals file can be reused for zoom3 and sdp3630
in addition to zoom2.
Also remove unused struct omap_board_config_kernel entry.
NOTE: Keep the twl4030_madc_platform_data and twl4030_platform_data
entries in board-zoom2.c to avoid merge conflicts with the pending
patches in MFD tree. These entries will be removed later as a fix.
Following list shows the commonality across the three platforms and hence the
case for software reuse:
Peripheral zoom2 zoom3 sdp3630
---------------------------------------
Ethernet smsc smsc smc
NOR n/a n/a B
Onenand n/a n/a B
HDMI A A B (present on different i2c)
NAND A A A (same nand)
SDRAM A A A (same sdram)
Keypad A A A (same twl)
Camera A A A (same sensor can be mounted)
LCD Display A A A (same wvga display)
OPPs A A A (same chip feature)
Audio A A A (same audio via twl5030)
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Migrate to smsc911x ethernet driver instead of smc911x driver.
The smsc911x ethernet driver supports NAPI and performs better
under heavy traffic. With the smc911x driver we were witnessing
very high iowait time for high IO load over NFS.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize vmmc and vmmc_aux regulators
Note that the omap3evm_twldata.vmmc1 and omap3evm_twldata.vsim
are set in omap3_evm_i2c_init() to avoid a merge conflict
with the MFD tree. These will be initialized in omap3evm_i2c_boardinfo
as a fix later on.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added runtime programming for the differences in EHCI interface between
OMAP3EVM revisions (Rev >= E) and (Rev < E).
Changes:
- EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E
uses GPIO pin 135.
- Rev >= E uses EHCI Vbus enable GPIO22 line.
- Rev >= E uses GPIO61 to select EHCI port either on main board or
on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have
EHCI port on main board.
- Currently GPIO61 it programmed to enable EHCI port on main
board only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.
Rev A to D : 0x01150000
Rev >= E : 0x92200000
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mainline merge of the 3430SDP support (commit 6fdc29e2)
seems to have messed up the 3430 defconfig completely.
Update the defconfig using a known good version
(SDP defconfig from v2.6.26-omap2 and current beagle defconfig)
as reference.
The image size is now 1.9 MB down from 2.4 MB earlier, and
the number of modules is 8, down from 203. Build time also
scales proportionally.
Other support (OneNAND, etc) can be enabled as needed.
Note that this patch intentionally does not update CONFIG_FB
related options to avoid merge conflicts with the pending
omap_dss2 patches.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the SYSFS_DEPRECATED flag from OMAP3 board defconfigs
This is a deprecated feature no longer needed.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch disables a GPIO module when all pins of a GPIO
module are inactive (clock gating forced at module level) and
enables the module when any gpio in the module is requested.
The module is enabled only when "mod_usage" indicates that no GPIO
in that module is currently active and the GPIO being requested
is the 1st one to be active in that module.
Each module would be disabled in omap_gpio_free() API when all
GPIOs in a particular module becomes inactive. The module is
re-enabled in omap_gpio_request() API when a GPIO is requested
from the module that was previously disabled.
Since individual GPIO's bookkeeping is added in this patch
via "mod_usage", the same is used in omap_set_gpio_debounce()
& omap_set_gpio_debounce_time() APIs to ensure that the gpio being
used is actually "requested" prior to being used (Nishant Menon's
<nm@ti.comSuggestion)
GPIO module level details are specific to hardware and hence
introducing this patch in low level layer (plat-omap/gpio.c)
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleanup the coding style in id.c while avoiding unneeded switch()
statements.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch uses a tasklet implementation for
sending mailbox messages.
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, this facilitates both the tesla and ducati
sides to request for the same irq through an
omap_mbox_get() call.
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds code changes in the mailbox driver module to
add support for OMAP4 mailbox.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Also removed from tx_data
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
No need to handle it in isr, since irq won't happen during isr.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Any protocol should be handled in the upper layer and mailbox driver
shouldn't care about the contents of messages.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds resource information of mailbox driver for
OMAP4 mailbox module. Register base address also added
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds changes to the build related files of mailbox
driver
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
map_iovm_area is only called from a context where its second argument is
known not to be NULL, so drop the unnecessary test. If new could be NULL,
the initialization of da should be moved below the test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
All of the OMAP3 IVA physical address macros in
plat-omap/include/plat/omap34xx.h are wrong[1]:
OMAP34XX_IVA_INTC_BASE: The IVA interrupt controller does not appear
to be accessible from the L3 interconnect, and in any case is
definitely not at 0x40000000; the latter address appears to be the
internal IVA physical address base for the OMAP2420's interrupt control[2].
OMAP34XX_DSP_BASE: The section of L3 physical address space mapped to
the IVA starts at 0x5c000000, not 0x58000000.
OMAP34XX_DSP_MEM_BASE: It's not clear what this refers to, but it's not
in the L3 IVA address space.
OMAP34XX_DSP_IPI_BASE: The Intrusive Port Interface is a relic from
the OMAP2420 days and no longer applies to OMAP3.
OMAP34XX_DSP_MMU_BASE: The DSP MMU is mapped at 0x5d000000, not 0x5a000000.
Nothing that uses these can possibly be working, so drop them. When
future code needs these, correct versions can be added in.
1. OMAP34xx Multimedia Device Silicon Revision 3.1.x Rev. W, Table 2-8:
"L3 Interconnect View of the IVA2.2 Subsystem Memory Space." p. 229.
2. OMAP2420 Multimedia Processor Silicon Revision 2.1.1, 2.2 (Rev. Q),
section 2.2.4.1, "IVA Memory Space Seen by L3", p. 132.
3. ibid., section 4.3.11, "DSP IPI Overview", p. 200.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When listing the various SoC features, print them on the same line.
So, instead of this
OMAP3430/3530 ES3.1
- l2cache : Y
- iva : Y
- sgx : Y
- neon : Y
- isp : Y
you get this:
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3_check_revision() does not depend on omap3_check_features()
move this above so that we can add logic based on revision
detected in check_features.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For ease of use it is preferrable to build in HSMMC driver
rather than build it as kernel module. This patches updates
default configuration for omap3evm to reflect this change.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The speed ctrl bit for MMC I/O is part of CONTROL_PROG_IO1 register
in omap3630.This patch sets it up accordingly.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The HSMMC1 controller on omap3630 supprts only 4-bit mode. If cpu
is 3630 configure HSMMC1 wires to 4-bit.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the cpu_is_omap3430() check to cpu_is_omap34xx() to allow HSMMC1/2
mux configuration for omap3630.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The use of the spin lock, which supposed to protect the the
dma_op_mode causing "INFO: inconsistent lock state" on
playback start.
Remove the spin locks around the dma_op_mode, when it's
purpuse is to protect the dma_op_mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way it's more object oriented and easier to see what is happening.
No functional changes.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cache flush operation is handled in the upper client layer and iovmm
modules doesn't have to care about it. This patch will improve some
performance with current camera isp driver.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MPU side (v)-(p) mapping is necessary only if IOVMF_MMIO is set in
"flags".
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for EHCI driver.
Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com>
and Anand Gadiyar <gadiyar@ti.com>.
Overo support added by Olof Johansson <olof@lixom.net>
Beagle support added by Koen Kooi <koen@beagleboard.org>
CM-T32 support added by Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing declarations to allow the recently introduced
ehci-omap driver to build on OMAP3
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM35xx is functionally similar to OMAP3430 ES3.1 from a
powerdomain/clockdomain perspective. This patch initializes the
omap_chip bits on AM35xx for use by powerdomain and clockdomain code.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support to detect AM3505/AM3517 devices at runtime.
Also updates the CPU names printed during boot.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
3630 is getting treated like next rev of 3430
omap_chip.oc variable has to be updated for 3630 version
Otherwise the Core power domain is not getting registered.
This gets used in the registration of power domains in:
"arch/arm/mach-omap2/powerdomains34xx.h"
core_34xx_es3_1_pwrdm
OMAP_CHIP_INIT(CHIP_GE_OMAP3430ES3_1)
Core power doman will get registered for 3630 only when .oc is
populated correctly.
Tested on Zoom3(3630) board
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Ari Kauppi <kauppi@papupata.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3630 is the latest in the family of OMAP3 devices
and among the changes it introduces are:
New OPP levels for new voltage and frequency levels. a bunch of
Bug fixes to various modules feature additions, notably with ISP,
sDMA etc.
Details about the chip is available here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606
Strategy used:
Strategy to introduce this device into Linux was discussed here:
Ref: http://marc.info/?t=125343303400003&r=1&w=2
Two approaches were available:
a) Consider 3630 generation of devices as a new family of silicon
b) Consider 3630 as an offshoot of 3430 family of devices
As a common consensus, (b) seems to be more valid for 3630 as:
* There are changes which are easily handled by using "FEATURES"
infrastructure.
For details how to do this, see thread:
http://marc.info/?t=125050998500001&r=1&w=2
* Most of existing 34xx infrastructure can be reused(almost 90%+)
- so no ugly if (cpu_is_omap34xx() || cpu_is_omap36xx())
all over the place
- lesser chance of bugs due to reuse of proven code flow
- 36xx specific handling can still be done where required
within the existing infrastructure
NOTE:
* If additional 34xx series are added, OMAP3430_REV_ESXXXX can be
added on top of the existing 3630 ones are renumbered
This patch was tested on SDP3430, boot tested on 3630 platform using
3430sdp defconfig
Signed-off-by: Madhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Cc: Allen Pais <allen.pais@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Sergio Alberto Aguirre Rodriguez <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add runtime check for these OMAP35x variations
based on the detected Si features:
OMAP3503, OMAP3515, OMAP3525 and OMA3530.
Also, delayed the call to pr_info() into actual
variant is detected in omap3_cpuinfo()
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP35x family has multiple variants differing
in the HW features. This patch detects these features
at runtime and prints information during the boot.
Since most of the code seemed repetitive, macros
have been used for readability.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The l3_ocpi_ck clock is needed on omap7xx processors for USB.
Additionally, bit 8 of the SOFT_REQ_REG needs to be enabled for
the usb_dc_ck on omap7xx, which is a different bit than that
of the omap16xx-defined clock of the same name.
I added a provision for the usb_dc_ck and l3_ocpi_ck clocks as
dc_clk and hhc_clk, respectively, for omap7xx CPUs. Additionally,
I added a check in machine_without_vbus_sense for all omap7xx
devices, as presently I know of no omap7xx-based devices that
have vbus sense, and it made more sense to me to use a cpu check
here than to spell out each machine one at a time. Finally, DMA
is disabled for omap7xx, as it causes problems with these chips.
Cc: linux-usb@vger.kernel.org
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC mux pins normally used by omap chips in devices.c
are different from what is needed by omap7xx chips. This
change adds a conditional around the mux setup code to
enable the correct mux pins.
The omap730 and omap850 both use a different clock for the "fck"
clock of the MMC interface than other omap processors based on the
SOFT_REQ_REG, pin 12. The "ick" clock is the same as that used
by other omap processors.
* Added the missing clock definition as mmc3_ck to clock.h
* Added the clock definition to omap_clks in clock.c
* Added CK_7XX to the mmci-omap.0 "ick" clock already in clock.c
With these changes, it is now possible to initialize and use MMC
cards with omap730 and omap850 devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zoom2/Zoom3 kind of boards do not use omap uarts for console.
These use external debug board for console.
So these boards should not have "Uncompressing Kernel...."
log put on omap uarts.
By interoducing OMAP_LL_DEBUG_NONE option,
unnecessary writes to omap uarts is avoided.
In future, the DEBUG_LL interface will be enhanced
to use external debug board.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminate OMAP_MAX_NR_PORTS
Note that also the null terminator entry for omap1
serial_platform_data needs to be now removed to avoid
oopsing.
Note that mach-omap1 uses struct plat_serial8250_port
array, which requires a null terminator at the end,
and that's why we need to use ARRAY_SIZE - 1. This
is not needed on mach-omap2 as the array used is
struct omap_uart_state, and does not use a null
terminator.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize some of the RX-51 input GPIO lines as gpio keys. Enable gpio
keys as a module in rx51_defconfig.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
audio_mclk value is going to be handled by the
twl4030-codec MFD driver, configure the correct
value for boards, which is using the twl4030 audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add needed platform data for the twl4030_codec MFD on boards,
where the audio part of the twl4030 codec is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If CONFIG_AKITA is not set, spitz fails to compile. It worked ok in
rc5. Fix is one more ifdef...
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
I stumbled over two small things regarding the .index field assignment
in the dynamically created cpu frequency tables for pxa2xx and pxa3xx.
Even though that doesn't currently cause any problem, it should still be
fixed in case the logic in the CPUFREQ core changes.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
d451564 broke ARM by requiring KM_IRQ_PTE, KM_NMI and KM_NMI_PTE to
always be defined. Solve this by providing invalid definitions for
these constants, but only if CONFIG_DEBUG_HIGHMEM is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Setup platform parameters in at91sam9rl-ek board to be passed to
atmel_tsadcc touchscreen.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some header files were reordered while I was at it.
The only device currently registered is the ATLAS PMIC (MC13783) chip.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit splits the support code for LogicPD's mx31lite hardware
into module and board specific parts.
This introduces a new mandatory coreparam called 'mx31lite_baseboard'
which specifies the base board support to use. For now, only the LiteKit
development board is supported, and developers of own boards are
encouraged to use that as reference.
The UART support moved to the board code.
Some comments were amended along the way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix underruns by using dma to copy 1st to sram
in a ping/pong buffer style and then copying from
the sram to the ASP. This also has the advantage
of tolerating very long interrupt latency on dma
completion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the left and right 16 bit samples to be shifted out as 1
32 bit sample.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP: cs should be positive in gpmc_cs_free()
omap: fix unlikely(x) < y
omap3: clock: Fixed dpll3_m2x2 rate calculation
omap3: clock: Fix the DPLL freqsel computations
omap: Fix keymap for zoom2 according to matrix keypad framwork
The index `cs' is signed, test whether it is negative before we release
gpmc_cs_mem[cs].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The closing parenthesis was not in the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
For consistency drop & in front of every proc_handler. Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Many SoCs have their I2S pins MUXed with other functions. So we need
to pass a callback for driver to configure the pins appropriately.
Hence, the need of platform data and this header.
As and when needed new callbacks and structure pointers maybe added to this
header.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current calculation does not take into account any changes to M2 divisor, and
thus when we change VDD2 OPP, dpll3_m2x2 rate does not change. Fixed by
re-routing dpll3_m2x2 parent to dpll3_m2.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the freqsel value computation. Use n instead of (n+1)
The formula in the TRM uses a zero-based N, hence the (n+1); however
at this point in the clock34xx.c code, N is one-based.
Hayati Bayrakdar <h-bayrakdar@ti.com> and Nishanth Menon <nm@ti.com> helped
track down this bug.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: modified commit message]
Cc: Hayati Bayrakdar <h-bayrakdar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: ensure mfp is in correct range in mfp_{read,write}
[ARM] pxa/hx4700: fix hx4700 touchscreen pressure values
ARM: 5787/1: U300 COH 901 331 fixes
ARM: Fix warning in sa1100-flash.c
[ARM] Kirkwood: disable propagation of mbus error to the CPU local bus
[ARM] pxa: fix incorrect mfp_to_gpio() conversion
[ARM] pxa/colibri: fix AC97 ifdefs and add missing include
[ARM] pxa: fix missing underscores in mfp-pxa910.h
[ARM] pxa: fix interrupts number calculation when CONFIG_PXA_HAVE_ISA_IRQS=y
Resolve the conflict between v2.6.32-rc7 where dn_def_dev_handler
gets a small bug fix and the sysctl tree where I am removing all
sysctl strategy routines.
Interpretation of 'row' and 'col' got reversed in matrix keymap
framework. Also last element '0', present in keymap array, is no
more needed.
Correcting zoom2 keyboard keymap accordingly.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure we do not read/write outside array boundaries with a negative index.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
hx4700 touchscreen events were being dropped in ads7846_rx() because their
pressure values consistently exceeded the platform maximum of 512; a sample
of 256 pressure values were in the range 531 to 815. Doubling the platform
maximum to 1024 allows hx4700 touchscreen events to pass the test.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This will fix some small issues with the COH 901 331 RTC driver:
- Interrupt is disabled after alarm so that we don't fire
multiple interrupts.
- We return 0 from the coh901331_alarm_irq_enable() ridding
a compile warning.
- We alter the name in the U300 device registry to match that
of the driver so they sucessfully resolve.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.
Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Many Atmel SOC are embedding a LCD controller. This patch removes the long
dependency line for this Atmel LCD framebuffer driver configuration entry.
The HAVE_FB_ATMEL configuration option is located in the video Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Instead of adding "depends on" at config level, introduce HAVE_* config
variables. Add them at machine or soc level to specify the ability of a
particular support.
It will ease new board introduction and readability.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Those "depends on" are a double check as all machine entries are
surrounded by "if <ARCH_xxx>" conditions.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.
Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
The address area of the NFC in the i.MX35 silicon is much larger than 4k.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to Russell King handle_edge_irq is only useful for "edge-based
inputs where the controller does not remember transitions with the input
masked."
So using handle_edge_irq unconditionally for both edge and level irqs is
wrong. Testing showed that the controller does remember transitions
while the interrupt is masked. So use handle_level_irq unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The ARC USB OTG Core has support for accessing ULPI tranceivers
through so called ULPI viewports. Export a set of function for use with
the USB OTG framework.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have two mt9t031 cameras that have a muxed bus on the robot.
Only one is currently initialized because of limitations in
soc_camera that should be removed later.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We get rid of CTS/RTS lines on uart0 on our platform.
This is the port we use as main kernel console. We do not
want it to be blocking because of CTS/RTS signals, not allowing
the system to boot or print messages.
However we often use it with a bluetooth module needing CTS/RTS
lines as backup login in case of trouble. To be able to use it,
we assert CTS low so that the module can always send chars.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The RTC chip Seiko Instruments S-35390A is connected to the Application
Processor over the second bus i2c with the hard coded address 0x30.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This add pin allocation an device registration for the
second bus i2c.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Armadillo500 Correct bus length for SMSC9118 on board chip.
The SMSC9118 network chip is connected to the data bus with a 16 bit
interface, not 32 as early suggested.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are two low active Buttons on boards.
This patch connect those to the Input Subsystem over gpio-keys driver.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The chip is actually located on the module, not on the base board. But
other base boards might add more SPI devices, so the spi_board_info
struct must be separated from the module code.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the two SPI busses found on the lilly1131 module.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The module does not use these pins for I2C but for SPI.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove the code duplication found in the setup files of TS-219 and
TS-41x.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Add two new models from QNAP to the help text. They are compatible
with the TS-119/TS-219 and therefore supported by the current code.
The only difference is that they have less RAM (256 MB instead of
512 MB), a slower CPU (800 MHz vs 1.2 GHz) and a plastic case.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Disable propagation of mbus errors to the CPU local bus, as this causes
mbus errors (which can occur for example for PCI aborts) to throw CPU
aborts, which we're not set up to deal with.
Reported-by: Dieter Kiermaier <dk-arm-linux@gmx.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
MPP36 is used on the QNAP TS-11x/TS-21x devices to indicate how
much RAM there is: it's high for 512 MB RAM (TS-x19) and low for
256 MB (TS-x10). While this may not be very useful, let's add
it for completeness.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Add support for the QNAP TS-410, TS-410U, TS-419P and TS-419U
Turbo NAS.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
