Removed define H_CB_ALIGNMENT which is already defined in include/asm-powerpc/hvcall.h
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix: Must check for nullpointer before dereferencing it - not afterwards.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a bug reported in:
http://bugzilla.kernel.org/show_bug.cgi?id=7438
tg3_close() turns off the PHY if WoL and ASF are both disabled. On
the next tg3_open(), some devices such as the 5752M will not be
brought up correctly without a PHY reset early in the reset sequence.
The PHY clock is needed for some internal MAC blocks to function
correctly.
This problem is fixed by always resetting the PHY early in
tg3_reset_hw() when it is called from tg3_open() or tg3_resume().
tg3_setup_phy() can then be called later in the sequence without the
reset_phy parameter set to 1, since the PHY reset is already done.
Update version to 3.68.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm43xx driver uses 4 locations in the devices sprom to determine
the behavior of the leds. Certain defaults are assigned if all bits are
set in those locations. On at least one BCM4303 chip, the sprom contains
values other than the default, which executes an assertion placed in the
default case of a following switch statement. This patch makes the leds
on the above mentioned interface behave correctly. In addition, it limits
the number of logged messages to 20 for the case of unexpected values in
the sprom locations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a netdev watchdog timeout problem.
The software needs to call netif_tx_disable before running the
hardware calibration code. The problem condition can be shown by the
following timegraph.
|---5secs - ~10 jiffies time---|---|OOPS
^ ^
last real TX periodic work stops netif
At OOPS, the following happens:
The watchdog timer triggers, because the timeout of 5secs
is over. The watchdog first checks for stopped TX.
_Usually_ TX is only stopped from the TX handler to indicate
a full TX queue. But this is different. We need to stop TX here,
regardless of the TX queue state. So the watchdog recognizes
the stopped device and assumes it is stopped due to full
TX queues (Which is a _wrong_ assumption in this case). It then
tests how far the last TX has been in the past. If it's more than
5secs (which is the case for low or no traffic), it will fire
a TX timeout.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the manfid CIS should be at least 4, and it's normally 4.
It's incorrect to require it to be at least 5. This breaks support for
most (if not all) cards.
The right place to ensure that we don't access beyond the CIS buffer is
to strengthen another check. Make sure that the next tuple begins at
least at the CIS buffer end (in which case we stop processing) or
before that.
Reported by ph35sm@free.fr
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sky2 driver uses a single NAPI poll routine for both ports on dual ported
cards (because there is a single IRQ and status ring). Netpoll makes assumptions
about the relationship between network device and NAPI that aren't correct
on the second port, this will cause the port to never clear work.
Most systems, just have single port, so not a big issue.
The easy fix is just make the second port, not netpoll capable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I don't want my code to downgraded to GPLv3 because of
cut-n-pasted the comments. These files which I hold copyright
on were started before it was clear what GPLv3 was going to be.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Checks for NULL dev_alloc_skb() and returns on true to avoid subsequent
dereference.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Christoph Hellwig <hch@infrared.org>
Signed-off-by: David Rientjes <rientjes@cs.washington.edu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to keep defining PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE
in the driver code since it is now defined in pci_ids.h.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2 driver is no longer in experimental state.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
modprobe n2 with no parameters or no such devices
will get confusing error message.
# modprobe n2
... Kernel does not have module support
This patch replaces return code from -ENOSYS to -EINVAL.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
drivers/net/wan/n2.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Call platform_driver_unregister() before return when no cards found.
(fixes data corruption when no cards found)
- Check platform_device_register_simple() return value
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mike Phillips <mikep@linuxtr.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
drivers/net/tokenring/proteon.c | 9 +++++++--
drivers/net/tokenring/skisa.c | 9 +++++++--
2 files changed, 14 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Flooding the console with error messages for every RX FIFO overrun,
checksum error and framing error isn't very sensible. Each of these
errors can occur during normal operation, so stop printk'ing error
messages for RX errors at all.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ray Lehtiniemi reported that an incoming UDP packet flood can lock up
the ep93xx ethernet driver. Herbert Valerio Riedel noted that due to
the way ep93xx_eth manages the RX/TXstatus rings, it cannot distinguish
a full ring from an empty one, and correctly suggested that this was
likely to be causing this lockup to occur.
Instead of looking at the hardware's RX/TXstatus ring write pointers
to determine when to stop reading from those rings, we should just check
every individual RX/TXstatus descriptor's valid bit instead, since there
is no other way to distinguish an empty ring from a full ring, and if
there is a descriptor waiting, we take the hit of reading the descriptor
from memory anyway.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Wed, 25 Oct 2006 18:03:13 +0200 Toralf Förster wrote:
> WARNING: "arp_broken_ops" [drivers/net/wan/sealevel.ko] undefined!
> make[1]: *** [__modpost] Error 1
> make: *** [modules] Error 2
>
> Here's the config:
...
> # CONFIG_INET is not set
> CONFIG_SEALEVEL_4021=m
Sealevel uses arp_broken_ops so it needs to depend on INET.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a2b98a697f.
As per Guennadi Liakhovetski, the mac address change support code breaks
some normal uses (_without_ any address changes), and until it's all
sorted out, we're better off without it.
Says Francois:
"Go revert it.
Despite what I claimed, I can not find a third-party confirmation by
email that it works elsewhere.
It would probably be enough to remove the call to
__rtl8169_set_mac_addr() in rtl8169_hw_start() though."
See also
http://bugzilla.kernel.org/show_bug.cgi?id=6032
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a replacement for the broad manufactor/card ID match we commented out
because of conflicts with pcnet_cs, add two product ID matches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
CRYPTO_MANAGER is selected automatically by CONFIG_ECB and CONFIG_CBC.
config CRYPTO_ECB
tristate "ECB support"
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
I've added CONFIG_ECB to the ones you mentioned and CONFIG_CBC to
gssapi.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Account for the interface being closed before disabling polling
on a device, to fix shutdown on some systems that explcitly close
the netdevice before calling shutdown.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Move the length (rx_bytes counter) adjustment of 4 bytes down to after the
TBI_ACCEPT workaround.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
82571 and newer chispets don't need to limit desc. length to 4kb and can
handle 8kb sizes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allocations using alloc_page are taking too long for normal MTU, so
use LPE only for jumbo frames.
Signed-off-bu: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Threshold bitmasks for prefetch, host and writeback were clearing
bits that they were not supposed to. The leftmost 2 bits in the byte
for each threshold are reserved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The MANC register should not be read for PCI-E adapters at all, as well as
82543 and older where 82543 would master abort when this register was
accessed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
On Thu, Oct 12, 2006 at 06:22:14PM +1000, David Gibson wrote:
> Your recent ibmveth commit, 751ae21c6c
> ("fix int rollover panic"), causes a rapid oops on my test machine
> (POWER5 LPAR).
>
> I've bisected it down to that commit, but am still investigating the
> cause of the crash itself.
Found the problem, I believe: an object lesson in the need for great
caution using ++.
[...]
@@ -213,6 +213,7 @@ static void ibmveth_replenish_buffer_poo
}
free_index = pool->consumer_index++ % pool->size;
+ pool->consumer_index = free_index;
index = pool->free_map[free_index];
ibmveth_assert(index != IBM_VETH_INVALID_MAP);
Since the ++ is used as post-increment, the increment is not included
in free_index, and so the added line effectively reverts the
increment. The produced_index side has an analagous bug.
The following change corrects this:
The recent commit 751ae21c6c introduced
a bug in the producer/consumer index calculation in the ibmveth driver
- incautious use of the post-increment ++ operator resulted in an
increment being immediately reverted. This patch corrects the logic.
Without this patch, the driver oopses almost immediately after
activation on at least some machines.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When closing the driver or reinitializing the hardware there is the
usual del_timer() race condition that exists when timers re-add
themselves. Fix by conversion to del_timer_sync().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
changes due to qe_lib changes include:
o removed inclusion of platform header file
o removed platform_device code, replaced with of_device
o removed typedefs
o uint -> u32 conversions
o removed following defines:
QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER,
BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET
because they hid sizeof/in_be32/out_be32 operations from the reader.
o removed irrelevant comments, added others to resemble removed BD_ defines
o const'd and uncasted all get_property() assignments
bugfixes, courtesy of Scott Wood, include:
- Read phy_address as a u32, not u8.
- Match on type == "network" as well as compatible == "ucc_geth", as
device_is_compatible() will only compare up to the length of the
test string, allowing "ucc_geth_phy" to match as well.
- fixes the MAC setting code in ucc_geth.c. The old code was overwriting and dereferencing random stack contents.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The reason sky2 driver was locking up on transmit on the Yukon-FE chipset
is that it was misconfiguring the internal RAM buffer so the transmitter
and receiver were sharing the same space.
The code assumed there was 16K of RAM on Yukon-FE (taken from vendor driver
sk98lin which is even more f*cked up on this). Then it assigned based on that.
The giveaway was that the registers would only hold 9bits so both RX/TX
had 0..1ff for space. It is a wonder it worked at all!
This patch addresses this, and fixes an easily reproducible hang on Transmit.
Only the Yukon-FE chip is Marvell 88E803X (10/100 only) are affected.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During the handling of the PCI error recovery sequence, the current e1000
driver erroneously blocks a device reset for any but the first PCI
function. It shouldn't -- this is a cut-n-paste error from a different
driver (which tolerated only one hardware reset per hardware card).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- move definition of 'tmc' and 'br' locals closer to usage
- handle clock_rate_calc() error
- propagate errors back to upper level open routine
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit 4596c75c23 as
requested by Olaf Hering. It causes compile errors, and says Olaf:
"This change is also wrong, the autoloading works perfect with 2.6.18,
no need to add random PCI ids.
See commit a0245f7ad5, platform devices
have now a modalias entry in sysfs. The network card is not a PCI
device."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (36 commits)
[Bluetooth] Fix HID disconnect NULL pointer dereference
[Bluetooth] Add missing entry for Nokia DTL-4 PCMCIA card
[Bluetooth] Add support for newer ANYCOM USB dongles
[NET]: Can use __get_cpu_var() instead of per_cpu() in loopback driver.
[IPV4] inet_peer: Group together avl_left, avl_right, v4daddr to speedup lookups on some CPUS
[TCP]: One NET_INC_STATS() could be NET_INC_STATS_BH in tcp_v4_err()
[NETFILTER]: Missing check for CAP_NET_ADMIN in iptables compat layer
[NETPOLL]: initialize skb for UDP
[IPV6]: Fix route.c warnings when multiple tables are disabled.
[TG3]: Bump driver version and release date.
[TG3]: Add lower bound checks for tx ring size.
[TG3]: Fix set ring params tx ring size implementation
[NET]: reduce per cpu ram used for loopback stats
[IPv6] route: Fix prohibit and blackhole routing decision
[DECNET]: Fix input routing bug
[TCP]: Bound TSO defer time
[IPv4] fib: Remove unused fib_config members
[IPV6]: Always copy rt->u.dst.error when copying a rt6_info.
[IPV6]: Make IPV6_SUBTREES depend on IPV6_MULTIPLE_TABLES.
[IPV6]: Clean up BACKTRACK().
...
When rebooting with netconsole over e100, the driver shutdown code would
deadlock with netpoll. Reduce shutdown code to a bare minimum while retaining
WoL and suspend functionality.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As BHs are off in loopback_xmit(), preemption cannot occurs, so we can
use __get_cpu_var() instead of per_cpu() (and avoid a
preempt_enable()/preempt_disable() pair)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The minimum tx ring size must be greater than MAX_SKB_FRAGS or 3
times that on some chips with TSO bugs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the implementation of the ethtool set ring parameters for the
tg3 transmit ring. The size of tx_pending is taken into account
before doing a netif_wake_queue. This prevents the interface from
locking up when smaller transmit ring sizes are used.
Signed-off-by: Ranjit Manomohan <ranjitm@google.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dont need a full struct net_device_stats (currently 23 long : 184 bytes on
x86_64) per possible CPU, but only two counters : bytes and packets
We save few CPU cycles too in loopback_xmit() not updating 4 fields, but 2.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'ubuntu-updates' of master.kernel.org:/pub/scm/linux/kernel/git/bcollins/ubuntu-2.6:
[pci_ids] Add Quicknet XJ vendor/device ID's.
[valkyriefb] Ifdef for when CONFIG_NVRAM isn't enabled.
[platinumfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[igafb] Add pci dev table for module auto loading.
[controlfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[hid-core] TurboX Keyboard needs NOGET quirk.
[ixj] Add pci dev table for module auto loading.
[initio] Add pci dev table for module auto loading.
[fdomain] Add pci dev table for module auto loading.
[BusLogic] Add pci dev table for auto module loading.
[mv643xx] Add pci device table for auto module loading.
[alim7101] Add pci dev table for auto module loading.
This reverts earlier change that attempted to fix flow control.
Device needs to discard pause frames, otherwise it hangs after a while.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
When using flow control, the PHY needs to accept multicast pause frames.
Without this fix, these frames were getting discarded by the PHY before
doing any flow control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Under high load it is possible to make the receiver FIFO get overloaded.
The driver/hardware recover properly, so there is no reason to fill the log
with lots of extra messages, just update counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The result of flow control negotiation should not limit the next
negotiatition. If board is plugged into an old half duplex 10Mbit port,
without pause, then replugged into a gigabit port, it should negotiate
what is desired, not inherit that last negotiation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The result of duplex negotiation is avaliable in the phy status
register, so use that to simplify code and avoid rereading the PHY.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
When PHY is turned off on shutdown, it causes the IRQ to get stuck on.
Make sure and disable the IRQ first, and if IRQ occurs when device
is not running, don't access PHY because that will hang.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The workaround timer is not needed in most systems with proper IRQ
routing and by perodically waking up it adds to laptop power consumption.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Some motherboards don't implement MSI correctly. The driver handles this
but the warning is too verbose and overly cautious.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The airo driver used to break out of while loop if there were any signals
pending. Since it no longer checks for signals, it at least needs to check
if it needs to be frozen.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the Orinoco issue, I did an audit of other drivers for the same
issue. Three drivers were NULL terminating the ESSID, which could cause an
overflow in WE-21 when the ESSID has maximum size.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we enter the if(!zd) and set free to 1, we dereference zd in the exit
code.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the Orinoco driver overflow issue with
WE-21.
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
create_proc_entry() can fail and return NULL in setup_proc_entry(), the
result must be checked before dereferencing. (Coverity ID 1443)
init_wifidev() & setup_proc_entry() can also fail in _init_airo_card().
This adds the checks & cleanup code and removes some whitespace.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bcm43xx-softmac software currently fails when running on x86_64 systems
with more than 1GB RAM and one of the card variants with 30-bit DMA addressing.
This patch uses the address extension bits in the hardware to set the correct
DMA mask for the specific card in use.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus's tree now has a configuration option that prints a warning whenever
the returned value of any routine is ignored. This patch fixes the only such
warning for bcm43xx.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some race conditions in the WirelessExtension
handling and association handling code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a potential race condition in the periodic_work_handler routine
of bcm43xx-softmac. In addition to fixing this condition, the size of code is
reduced by moving the mutex lock outside the if.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for moving check_signature, change these users from asm/io.h
to linux/io.h
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adjust the pause threshold on slower systems to keep from getting overrun.
Since FIFO is 2K bytes, don't send XON pause until there is space for a full
frame.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The pci express error handling extensions don't work unless PCI access is via
mmconfig. Otherwise, all accesses to pci config registers greater than 256 fail.
Since the sky2 driver has other ways of getting to PCI config space, it works
around this short coming, but the pci_find_ext_capablity doesn't work.
This backs out commit 91aeb3edbc
Go back to hardcoding, since we know where the error registers are anyway.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=7222
Signed-off-by: Stephen Hemminger <shemmminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Want to be able to track downstream impact of fiber related
fixes.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do flow control negotiation properly. Don't let auto negotiation
status limit renegotiation. Separate desired pause values from
the result of auto negotiation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do correct mapping of pause and duplex when using 1000BaseX fiber
versions of the board.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PHY interrupt from the internal fiber is getting
stuck on when the link is down. Add code to handle the
transition and mask it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bugfix: rx descriptor release function fails to visit
the last entry while walking receive descriptor ring.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ring buffer descriptors are DMA-accessed bidirectionally,
but are not declared in this way. Fix this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cosmetic patch: give the variable holding the numer of descriptors
a more descriptive name, so to avoid confusion.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code attempts to start the TX dma every time a packet
is queued. This is too conservative, and wastes CPU time. This
patch changes behaviour to call the kick-dma function less often,
only when the tx queue is at risk of emptying.
This reduces cpu usage, improves performance.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove a dummy register read that is not needed.
This reduces CPU usage notably during transmit.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit side of the spider ethernet driver currently
places locks around some very large chunks of code. This
results in a fair amount of lock contention is some cases.
This patch makes the locks much more fine-grained, protecting
only the cirtical sections. One lock is used to protect
three locations: the queue head and tail pointers, and the
queue low-watermark location.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves transmit queue cleanup code out of the
interrupt context, and into the NAPI polling routine.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement basic low-watermark support for the transmit queue.
Hardware low-watermarks allow a properly configured kernel
to continously stream data to a device and not have to handle
any interrupts at all in doing so. Correct zero-interrupt
operation can be actually observed for this driver, when the
socket buffer is made large enough.
The basic idea of a low-watermark interrupt is as follows.
The device driver queues up a bunch of packets for the hardware
to transmit, and then kicks the hardware to get it started.
As the hardware drains the queue of pending, untransmitted
packets, the device driver will want to know when the queue
is almost empty, so that it can queue some more packets.
If the queue drains down to the low waterark, then an interrupt
will be generated. However, if the kernel/driver continues
to add enough packets to keep the queue partially filled,
no interrupt will actually be generated, and the hardware
can continue streaming packets indefinitely in this mode.
The impelmentation is done by setting the DESCR_TXDESFLG flag
in one of the packets. When the hardware sees this flag, it will
interrupt the device driver. Because this flag is on a fixed
packet, rather than at fixed location in the queue, the
code below needs to move the flag as more packets are
queued up. This implementation attempts to keep the flag
at about 1/4 from "empty".
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bugfix -- the rx chain is in memory after the tx chain --
the offset being used was wrong, resulting in memory corruption
when the size of the rx and tx rings weren't exactly the same.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turn off mis-interpretation of the queue-empty interrupt
status bit as an error.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The print message associated with the descriptor chain end interrupt
prints a bogs value. Fix that.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current receive interrupt mask sets a bogus bit that doesn't even
belong to the definition of this register. Remove it.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds a call to netif_stop_queue() when there is
no more room for more packets on the transmit queue.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the names of a few fields in the DMA control
register. There is no functional change.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Set the netdev watchdog timer.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Polite device drivers pad short packets to 60 bytes,
so that mean-spirited users don't accidentally DOS
some other OS that can't handle short packets.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bugfix: when cleaning up the transmit queue upon device close,
be sure to walk the entire queue.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The module param permsissions should bw read-only, not writable.
From: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch increases the Burst Address alignment from 64 to 1024 in the
Spidernet driver. This improves transmit performance for large packets.
From: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds version information as reported by
ethtool -i to the Spidernet driver.
From: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch includes a bug fix for the port state notification
and fixes the default queue sizes.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This eHEA patch covers required changes related to Anton Blanchard's new hvcall interface.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/ibmveth.c:939: error: too many arguments to function `ibmveth_interrupt'
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes eeprom read on big-endian architectures.
readw returns the data in CPU order. With cpu_to_le16 we convert it to little
endian, because "ptr" is a pointer to a _byte_ arrray. See the cast above. A
byte array is little endian.
The bug is:
Reading u16 values with readw, casting them into an u8 array and accessing
this u8 array as an u8 (byte) array. The correct fix is to swap the
CPU-ordering value returned by readw into little endian, as the u8 array is
little endian.
This compiles to nothing on little endian hardware (so it does not change b44
code on LE hardware), but _fixes_ code on BE hardware.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- fix: toshoboe_invalid_dev() was recently removed, but not all callers
were updated, causing the obvious linker error. Remove caller,
because the check (like the one removed) isn't used.
- fix: propagate request_irq() return value
- cleanup: remove void* casts
- cleanup: remove impossible ASSERTs
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
m68k_handle_int() split in two functions: __m68k_handle_int() takes
pt_regs * and does set_irq_regs(); m68k_handle_int() doesn't get pt_regs
*.
Places where we used to call m68k_handle_int() recursively with the same
pt_regs have simply lost the second argument, the rest is switched to
__m68k_handle_int().
The rest of patch is just dropping pt_regs * where needed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Eliminate check for irq handler 'dev_id==NULL' where the
condition never occurs.
- Eliminate needless casts to/from void*
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
If there are more than B44_MCAST_TABLE_SIZE groups in the dev->mc_list,
it will only listen to the first B44_MCAST_TABLE_SIZE that it sees.
This change makes the driver go into RXCONFIG_ALLMULTI mode if there
are more than B44_MCAST_TABLE_SIZE groups being subscribed to, similar
to other network drivers.
Noticed by Bill Helfinstine <bhelf@flitterfly.whirpon.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In bond_alb_monitor the bond->curr_slave_lock write lock is taken
and then dev_set_promiscuity maybe called which can take some time,
depending on the network HW. If a network IRQ for this card come in
the softirq handler maybe try to deliver more packets which end up in
a request to the read lock of bond->curr_slave_lock -> deadlock.
This issue was found by a test lab during network stress tests, this patch
disable the softirq handler for this case and solved the issue.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
BUG: warning at kernel/lockdep.c:1816/trace_hardirqs_on() (Not tainted)
Call Trace:
show_trace
dump_stack
trace_hardirqs_on
:forcedeth:nv_nic_irq_other
handle_IRQ_event
__do_IRQ
do_IRQ
ret_from_intr
DWARF2 barf
default_idle
cpu_idle
rest_init
start_kernel
_sinittext
These 3 functions nv_nic_irq_tx(), nv_nic_irq_rx() and nv_nic_irq_other()
are reachable from IRQ context and process context. Make use of the
irq-save/restore spinlock variant.
(Compile tested only, since I do not have the hardware)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some stats reported by ethtool -S on mv643xx_eth device are cleared
between each call. This patch fixes it.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a nasty bug that has been sitting there since the
very first versions of the driver, but is generating a panic because
we changed the number of 2K buffers for 2.6.16.
The consumer_index and producer_index are u32's that get incremented
on every buffer emptied and replenished respectively. We use
the {producer,consumer}_index mod'ed with the size of the pool to
pick out an entry in the free_map. The problem happens when the
u32 rolls over and the number of the buffers in the pool is not a
perfect divisor of 2^32. i.e. if the number of 2K buffers is 0x300,
before the consumer_index rolls over, our index to the free map =
0xffffffff mod 0x300 = 0xff. The next time a buffer is emptied, we
want the index to the free map to be 0x100, but 0x0 mod 0x300 is 0x0.
This patch assigns the mod'ed result back to the consumer and producer
indexes so that they never roll over. The second chunk of the patch
covers the unlikely case where the consumer_index has just been reset
to 0x0 and the hypervisor is not able to accept that buffer.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch changes the name of the proc file for each ibmveth adapter
from the network device name to the slot number in the virtual bus.
The proc file is created when the device is probed, so a change
in the name of the device will not be reflected in the name of the
proc file giving problems when identifying and removing the adapter.
The slot number is a property that does not change through the life
of the adapter so we use that instead.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a race that panics the kernel when opening the
device after a kdump. Without this patch there is a window where the
hypervisor can send an interrupt before all the structures for the
kdump ibmveth module are ready (because the hypervisor is not aware
that the partition crashed and that the virtual driver is reloading).
We close this window by disabling the interrupts before registering
the adapter to the hypervisor.
This patch depends on the "ibmveth: Harden driver initilisation" patch.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the net poll controller function to ibmveth to support
netconsole and netdump.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch has been floating around for a while now, Santi originally
sent it in March: http://www.spinics.net/lists/netdev/msg00471.html
After a kexec the ibmveth driver will fail when trying to register
with the Hypervisor because the previous kernel has not unregistered.
So if the registration fails, we unregister and then try again.
We don't unconditionally unregister, because we don't want to disturb
the regular code path for 99% of users.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The previous change to do fragmented receive (post 2.6.18) introduced a bug
where packets are passed up with size set to the size of the receive buffer
not the actual received data. IP silently trims this so it didn't show up
right away.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts one if() BUG(); to BUG_ON();
so it can be safely optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (29 commits)
[POWERPC] Fix rheap alignment problem
[POWERPC] Use check_legacy_ioport() for ISAPnP
[POWERPC] Avoid NULL pointer in gpio1_interrupt
[POWERPC] Enable generic rtc hook for the MPC8349 mITX
[POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class
[POWERPC] Create a "wrapper" script and use it in arch/powerpc/boot
[POWERPC] fix spin lock nesting in hvc_iseries
[POWERPC] EEH failure to mark pci slot as frozen.
[POWERPC] update powerpc defconfig files after libata kconfig breakage
[POWERPC] enable sysrq in pmac32_defconfig
[POWERPC] UPIO_TSI cleanup
[POWERPC] rewrite mkprep and mkbugboot in sane C
[POWERPC] maple/pci iomem annotations
[POWERPC] powerpc oprofile __user annotations
[POWERPC] cell spufs iomem annotations
[POWERPC] NULL noise removal: spufs
[POWERPC] ppc math-emu needs -fno-builtin-fabs for math.c and fabs.c
[POWERPC] update mpc8349_itx_defconfig and remove some debug settings
[POWERPC] Always call cede in pseries dedicated idle loop
[POWERPC] Fix loop logic in irq_alloc_virt()
...
ifb: replace missing comma to separate pr_debug arguments
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous hp100 changeset attempted to kill warnings, but was only
tested on !CONFIG_ISA platforms. The correct conditional compilation
setup involves tested CONFIG_ISA rather than just MODULE.
Fixes link on CONFIG_ISA platforms (i386) in current -git.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (37 commits)
[netdrvr] hp100: encapsulate all non-module code
drivers/net/wireless/{airo,ipw2100}: fix error handling bugs
[netdrvr] phy: Fix bugs in error handling
[PATCH] spidernet: Use pci_dma_mapping_error()
[PATCH] sky2: version 1.9
[PATCH] sky2: fragmented receive for large MTU
[PATCH] sky2: use netif_tx_lock instead of LLTX
[PATCH] sky2: incremental transmit completion
[PATCH] sky2: name irq after eth for irqbalance
[PATCH] sky2: workarounds for some 88e806x chips
[PATCH] sky2: use standard pci register capabilties for error register
[PATCH] sky2: gigabit full duplex negotiation
e100, e1000, ixgb: increment version numbers
ixgb: convert to netdev_priv(netdev)
ixgb: combine more rx descriptors to improve performance
e1000: possible memory leak in e1000_set_ringparam
e1000: Janitor: Use #defined values for literals
e1000: don't strip vlan ID if 8021q claims it
e1000: rework polarity, NVM, eeprom code and fixes.
e1000: driver state fixes (race fix)
...
The last in-kernel user of errno is gone, so we should remove the definition
and everything referring to it. This also removes the now-unused lib/execve.c
file that was introduced earlier.
Also remove every trace of __KERNEL_SYSCALLS__ that still remained in the
kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
File handles can be requested to send sigio and sigurg to processes. By
tracking the destination processes using struct pid instead of pid_t we make
the interface safe from all potential pid wrap around problems.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
airo:
* fix oops, if !CONFIG_PROC_FS (create_proc_entry always returns NULL)
* handle pci_register_driver() failure. if it fails, we really do
want to exit, rather than (as a comment indicates) return success
because-we-are-a-library.
* #if 0 have_isa_dev variable, which is assigned a value but never used
ipw2100:
* handle sysfs_create_group() failure
* handle driver_create_file() failure
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes readv() and writev() methods and replaces them with
aio_read()/aio_write() methods.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add infrastructure to track "maximum allowable latency" for power saving
policies.
The reason for adding this infrastructure is that power management in the
idle loop needs to make a tradeoff between latency and power savings
(deeper power save modes have a longer latency to running code again). The
code that today makes this tradeoff just does a rather simple algorithm;
however this is not good enough: There are devices and use cases where a
lower latency is required than that the higher power saving states provide.
An example would be audio playback, but another example is the ipw2100
wireless driver that right now has a very direct and ugly acpi hook to
disable some higher power states randomly when it gets certain types of
error.
The proposed solution is to have an interface where drivers can
* announce the maximum latency (in microseconds) that they can deal with
* modify this latency
* give up their constraint
and a function where the code that decides on power saving strategy can
query the current global desired maximum.
This patch has a user of each side: on the consumer side, ACPI is patched
to use this, on the producer side the ipw2100 driver is patched.
A generic maximum latency is also registered of 2 timer ticks (more and you
lose accurate time tracking after all).
While the existing users of the patch are x86 specific, the infrastructure
is not. I'd like to ask the arch maintainers of other architectures if the
infrastructure is generic enough for their use (assuming the architecture
has such a tradeoff as concept at all), and the sound/multimedia driver
owners to look at the driver facing API to see if this is something they
can use.
[akpm@osdl.org: cleanups]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch defines:
* a generic boolean-type, named 'bool'
* aliases to 0 and 1, named 'false' and 'true'
Removing colliding definitions of 'bool', 'false' and 'true'.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MSI is defined to be 32-bit write. The 5706 does 64-bit MSI writes
with byte enables disabled on the unused 32-bit word. This is legal
but causes problems on the AMD 8132 which will eventually stop
responding after a while.
Without this patch, the MSI test done by the driver during open will
pass, but MSI will eventually stop working after a few MSIs are
written by the device.
AMD believes this incompatibility is unique to the 5706, and
prefers to locally disable MSI rather than globally disabling it
using pci_msi_quirk.
Update version to 1.4.45.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For len equal to 4, we never call sppp_lcp_conf_parse_options(),
therefore rmagic does not get initialized.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce the disable_irq_nosync_lockdep_irqsave() and
enable_irq_lockdep_irqrestore() APIs. These are needed for NE2000; basically
NE2000 calls disable_irq and enable_irq as locking against the IRQ handler,
but both in cases where interrupts are on and off. This means that lockdep
needs to track the old state of the virtual irq flags on disable_irq, and
restore these at enable_irq time.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As suggested by Muli Ben-Yehuda this function is moved to generic code as
may be useful for all archs.
[akpm@osdl.org: fix]
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
FIFOCTL_RXERR and FIFOCTL_TXERR are undocumented bits, according to the
Sigmatel datasheet. We should thus not take any assumption on their values
and semantics.
Problem spotted by andrzej zaborowski <balrogg@gmail.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch detects the smsc-ircc chipset on the nx1000
(including nx7000 and nx7010) and the nx5000 HP/Compaq laptop series.
Patch from "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to NatSemi datasheet, the configuration base address for the PC8738x
family is 0x2e or 0x164. 0x0 doesn't appear in any datasheet.
Patch from Lamarque Vieira Souza <lamarque@gmail.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loopback device status structure is a singleton and doesn't
need to be allocated. Add ethtool_ops hooks to show checksum always on,
and make ethtool_ops const.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the inclusion of the stir421x code, we now need to select FW_LOADER
whenever we try to build the irda-usb code.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPPoE must advertise the underlying device's MTU via the ppp channel
descriptor structure, as multilink functionality depends on it.
Signed-off-by: Michal Ostrowski <mostrows@earthlink.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new 5709 device. This is a new 10/100 Mbps chip.
The mailbox access and firmware interface are quite different from
all other tg3 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the firmware polling logic into a separate function. This makes
the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY related fixes:
1. Fix Serdes WoL.
2. Fix loopback test on 10/100 only devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change to a different ASF heartbeat message code to improve
reliability.
There were some reports of unintended resets on real time kernels
where the timer may be slow and cause the heartbeat to be late.
Netpoll will also have the same problem because the timer irq will
be unavailable.
Using the new heartbeat code, the ASF firmware will also check the
ring condition before resetting the chip when the heartbeat is
expiring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve 5704S autoneg logic by using a serdes_counter field to keep
track of the transient states. This eliminates a 200 msec busy
loop in the code. Autoneg will take its course without the driver
busy waiting for it to finish.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifa_local, ifa_address, ifa_mask, ifa_broadcast and ifa_anycast are
net-endian. Annotated them and variables that are inferred to be
net-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net devices should depend on NETDEVICES, so revert part of
Paolo's previous patch.
See http://marc.theaimsgroup.com/?l=linux-kernel&m=115566326218740&w=2
for history.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A driver shouldn't compare to DMA_ERROR_CODE directly, use
pci_dma_mapping_error() instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use hardware support for chained receive to break up large frames
into multiple pages. This avoids having to do a mult-page allocation
that can fail on a busy system due to fragmented memory.
For normal size MTU, this code behaves the same.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netdevice transmit lock via netif_tx_lock rather than putting
lock in device specific code and using lockless transmit. The code is
cleaner using netif_tx_lock, and the performance is same.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since a transmit can take several control blocks, the old code waited
until the last control block was marked as done. This code processes
the return values incrementally. This makes slots in the tx ring available
and less chance of getting stuck.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the ethernet device name when requesting the irq because the
irqbalance daemon looks for the name when deciding policy.
Better to play along with this dubious heuristic.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Workarounds for 88e806x chips from the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the standard pci capability mechanism to access PCI express error
registers, rather than hard coding the offset. Mask off the PCI express
error from ever occuring on non-PCI express systems.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Look at the registers correctly, when doing gigabit full duplex.
Need to look for link partner result.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
[PATCH] bonding: update version number
[PATCH] git-netdev-all: pc300_tty build fix
[PATCH] Make PC300 WAN driver compile again
[PATCH] Modularize generic HDLC
[PATCH] more s2io __iomem annotations
[PATCH] restore __iomem annotations in e1000
[PATCH] 64bit bugs in s2io
[PATCH] bonding: Fix primary selection error at enslavement time
[PATCH] bonding: Don't mangle LACPDUs
[PATCH] bonding: Validate probe replies in ARP monitor
[PATCH] bonding: Don't release slaves when master is admin down
[PATCH] bonding: Add priv_flag to avoid event mishandling
[PATCH] bonding: Handle large hard_header_len
[PATCH] bonding: Remove unneeded NULL test
[PATCH] bonding: Format fix in seq_printf call
[PATCH] bonding: Convert delay value from s16 to int
[PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
Delete unused drivers/net/gt64240eth.h
[PATCH] skge: fiber support
[PATCH] fix possible NULL ptr deref in forcedeth
...
I neglected to properly update the version number in the recent
patch series; this sets it to something reasonable.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In file included from drivers/net/wan/pc300_tty.c:59:
drivers/net/wan/pc300.h:335: error: field 'pppdev' has incomplete type
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We experimented with more descriptor buffer writebacks and found that
values larger than 8 give HW problems, but 8 is safe and gives us some
improved performance.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Memory allocated for new tx_ring and rx_ring leaks if
e1000_setup_XX_resources() fails.c Also this patch reduces stack usage
(removed tx_new and rx_new) and uses kzalloc instead kmalloc+memset(0)
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
