Signed-off-by: Marko Ristola <marko.ristola@kolumbus.fi>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Demodulator status check made reliable
* Code simplification for Viterbi Sync check, makes
acquisition more reliable
* Implement a BER monitor
* Implement a Signal strength monitor
* Implement a "simple" UCB monitor, no real UCB monitor
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
You know, the worst endianness errors are not the cases where
people forget to byte-swap, but the cases where they either byte-swap
with the wrong size, or byte-swap when they shouldn't have done so at
all. Those ones defeat the casual reader of the code.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Ristola <marko.ristola@kolumbus.fi>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Control of more than one AV/C device at once --- e.g. camcorders, tape
decks, audio devices, TV tuners --- failed or worked only unreliably,
depending on driver implementation. This affected kernelspace and
userspace drivers alike and was caused by firewire-core's inability to
accept multiple registrations of FCP listeners.
The fix allows multiple address handlers to be registered for the FCP
command and response registers. When a request for these registers is
received, all handlers are invoked, and the Firewire response is
generated by the core and not by any handler.
The cdev API does not change, i.e., userspace is still expected to send
a response for FCP requests; this response is silently ignored.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (changelog, rebased, whitespace)
Make the local filter coefficients static and const. This will eliminate the
following sparse warnings (see "make C=1"):
* au8522_decoder.c:71:31: warning: symbol 'filter_coef' was not declared. Should it be static?
* au8522_decoder.c:113:31: warning: symbol 'lpfilter_coef' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove duplicated line on driver
[mchehab@redhat.com: second hunk of the original patch were already applied by another patch - remove it]
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Duncan Gibb <dg@duncangibb.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Make module_init static and mark it with __init.
Make module_exit static and mark it with __exit.
Mark probe functions with __devinit.
Make id table static and mark with __devinitconst.
This will eliminate the following sparse warnings (see "make C=1"):
* smsdvb.c:668:5: warning: symbol 'smsdvb_module_init' was not declared. Should it be static?
* smsdvb.c:682:6: warning: symbol 'smsdvb_module_exit' was not declared. Should it be static?
* smsusb.c:491:22: warning: symbol 'smsusb_id_table' was not declared. Should it be static?
* smsusb.c:567:5: warning: symbol 'smsusb_module_init' was not declared. Should it be static?
* smsusb.c:578:6: warning: symbol 'smsusb_module_exit' was not declared. Should it be static?
* smssdio.c:341:5: warning: symbol 'smssdio_module_init' was not declared. Should it be static?
* smssdio.c:353:6: warning: symbol 'smssdio_module_exit' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Eliminate the following sparse warnings (see "make C=1"):
* dib8000.c:125:15: warning: symbol 'coeff_2k_sb_1seg_dqpsk' was not declared. Should it be static?
* dib8000.c:130:15: warning: symbol 'coeff_2k_sb_1seg' was not declared. Should it be static?
* dib8000.c:134:15: warning: symbol 'coeff_2k_sb_3seg_0dqpsk_1dqpsk' was not declared. Should it be static?
* dib8000.c:139:15: warning: symbol 'coeff_2k_sb_3seg_0dqpsk' was not declared. Should it be static?
* dib8000.c:144:15: warning: symbol 'coeff_2k_sb_3seg_1dqpsk' was not declared. Should it be static?
* dib8000.c:149:15: warning: symbol 'coeff_2k_sb_3seg' was not declared. Should it be static?
* dib8000.c:154:15: warning: symbol 'coeff_4k_sb_1seg_dqpsk' was not declared. Should it be static?
* dib8000.c:159:15: warning: symbol 'coeff_4k_sb_1seg' was not declared. Should it be static?
* dib8000.c:164:15: warning: symbol 'coeff_4k_sb_3seg_0dqpsk_1dqpsk' was not declared. Should it be static?
* dib8000.c:169:15: warning: symbol 'coeff_4k_sb_3seg_0dqpsk' was not declared. Should it be static?
* dib8000.c:174:15: warning: symbol 'coeff_4k_sb_3seg_1dqpsk' was not declared. Should it be static?
* dib8000.c:179:15: warning: symbol 'coeff_4k_sb_3seg' was not declared. Should it be static?
* dib8000.c:184:15: warning: symbol 'coeff_8k_sb_1seg_dqpsk' was not declared. Should it be static?
* dib8000.c:189:15: warning: symbol 'coeff_8k_sb_1seg' was not declared. Should it be static?
* dib8000.c:194:15: warning: symbol 'coeff_8k_sb_3seg_0dqpsk_1dqpsk' was not declared. Should it be static?
* dib8000.c:199:15: warning: symbol 'coeff_8k_sb_3seg_0dqpsk' was not declared. Should it be static?
* dib8000.c:204:15: warning: symbol 'coeff_8k_sb_3seg_1dqpsk' was not declared. Should it be static?
* dib8000.c:209:15: warning: symbol 'coeff_8k_sb_3seg' was not declared. Should it be static?
* dib8000.c:214:15: warning: symbol 'ana_fe_coeff_3seg' was not declared. Should it be static?
* dib8000.c:218:15: warning: symbol 'ana_fe_coeff_1seg' was not declared. Should it be static?
* dib8000.c:222:15: warning: symbol 'ana_fe_coeff_13seg' was not declared. Should it be static?
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If val is a u64, then following:
val *= (u64)1 << 32;
val /= (u64)1 << 32;
should surely be better represented as:
val <<= 32;
val >>= 32;
Especially as, for the division, the compiler might want to actually do a
division:
drivers/built-in.o: In function `lgs8gxx_get_afc_phase':
drivers/media/dvb/frontends/lgs8gxx.c:250: undefined reference to `__udivdi3'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch to support DvbWorld DW2104 device modifications
with STV0903 and DS3000 demods as well as TeVii S660 and Prof 1100
Also replace some magic numbers with meaningfull variables.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support DiSEqC envelope mode. Feature is enabled by setting
config->diseqc_envelope_mode = true (default: disabled).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support 22 kHz tone control for lnbp21 and lnbh24.
(Overrides the 'set_tone' hook of the frontend driver.)
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll need to register a sysfs class for the IR devices. As such, the better
is to have the input_register_device()/input_unregister_device() inside
the ir register/unregister functions.
Also, solves a naming problem with V4L ir_input_init() function, that were,
in fact, registering a device.
While here, do a few cleanups at budget-ci IR logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, ir_input_free does more than just freeing the keytab. Better to
rename it as ir_input_unregister.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the behaviour of the dibusb-i2c-access which was previously changed to avoid accidental EEprom writes:
Now it allow i2c-reads without prepended i2c-writes, but it is still not doing anything in case the EEprom is addressed.
Thanks to Mario Bachmann for testing.
Tested-by: Mario Bachmann <grafgrimm77@gmx.de>
Cc: Mario Bachmann <grafgrimm77@gmx.de>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge two ifs: the condition is the same. The second if
uses the ncoeff which is initialized in the first if.
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add parameter to change the buffer size. This buffer size is specified
in number of Ts packet. This parameter is stored inside the state.
For firmware higher than 1.21, the xfer buffer size can be changed
inside the dib0700 usb bridge the firware version is stored inside the
state
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes most of the Codingstyle violations which were
introduced by the previous patch. Line length less that 80 chars are
not corrected.
Signed-off-by: Olivier Grenie <Olivier.Grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patchs adds support for the DiBcom DiB0090 RF tuner and for
DiBcom's reference design STK8096GP. Small extracts of the DiB0070 and
the DiB8000-driver into a common codebase.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Olivier Grenie <Olivier.Grenie@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PCTV 74e is not a design based on the dib0700-USB-device
controller thus we should not have its USB IDs inside.
This reverts partly:
Add support for PCTV 74e (Pinnacle) + fix USB vendor IDs
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for PCTV 74e (Pinnacle) and it fixes the USB vendor IDs for PCTV (f.k.a Pinnacle).
For convenience all new PCTV USB product IDs are also existing with Pinnacle's USB vendor ID.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device is bootingcorrectly, but no frontend is attached.
This patch corrects this behaviour.
Signed-off-by: Pedro Andres Aranda Gutierrez <paaguti@gmail.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Genpix is demodulating DVB-S-like signal with 8PSK modulation used) -
this non-standard behaviour was broken by rejecting 8PSK in a standard
DVB-S tune request. This problem is fixed by simply reverting back to
the drivers original behavior with this patch.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a fix to accept frequency with its center shifted.
The driver used to accept center frequencies of the normal UHF band channels,
but in ISDB-T, center frequency is shifted with 1/7MHz.
It was shifted internally in the driver,
but this patch enables to accept both types of frequency.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for five new Hauppauge Device USB IDs:
2040:b980
2040:b990
2040:c010
2040:c080
2040:c090
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (345 commits)
V4L/DVB (13542): ir-keytable: Allow dynamic table change
V4L/DVB (13541): atbm8830: replace 64-bit division and floating point usage
V4L/DVB (13540): ir-common: Cleanup get key evdev code
V4L/DVB (13539): ir-common: add __func__ for debug messages
V4L/DVB (13538): ir-common: Use a dynamic keycode table
V4L/DVB (13537): ir: Prepare the code for dynamic keycode table allocation
V4L/DVB (13536): em28xx: Use the full RC5 code on HVR-950 Remote Controller
V4L/DVB (13535): ir-common: Add a hauppauge new table with the complete RC5 code
V4L/DVB (13534): ir-common: Remove some unused fields/structs
V4L/DVB (13533): ir: use dynamic tables, instead of static ones
V4L/DVB (13532): ir-common: Add infrastructure to use a dynamic keycode table
V4L/DVB (13531): ir-common: rename the debug routine to allow exporting it
V4L/DVB (13458): go7007: subdev conversion
V4L/DVB (13457): s2250: subdev conversion
V4L/DVB (13456): s2250: Change module structure
V4L/DVB (13528): em28xx: add support for em2800 VC211A card
em28xx: don't reduce scale to half size for em2800
em28xx: don't load audio modules when AC97 is mis-detected
em28xx: em2800 chips support max width of 640
V4L/DVB (13523): dvb-bt8xx: fix compile warning
...
Fix up trivial conflicts due to spelling fixes from the trivial tree in
Documentation/video4linux/gspca.txt
drivers/media/video/cx18/cx18-mailbox.h
Randy Dunlap wrote:
> On Mon, 30 Nov 2009 10:07:21 -0800 Randy Dunlap wrote:
>
>> Stephen Rothwell wrote:
>>> Hi all,
>>>
>>> Changes since 20091127:
>>>
>>> The v4l-dvb tree lost its conflict.
>>
>> on i386 (X86_32):
>>
>> a 'double' variable is used, causing:
>>
>> ERROR: "__floatunsidf" [drivers/media/common/tuners/max2165.ko] undefined!
>> ERROR: "__adddf3" [drivers/media/common/tuners/max2165.ko] undefined!
>> ERROR: "__fixunsdfsi" [drivers/media/common/tuners/max2165.ko] undefined!
>
>
> linux-next-20091202:
>
> still have this one (above) and similar with
> drivers/media/dvb/frontends/atbm8830.c:
>
> drivers/built-in.o: In function `atbm8830_init':
> atbm8830.c:(.text+0x9012f9): undefined reference to `__udivdi3'
> atbm8830.c:(.text+0x901384): undefined reference to `__floatunsidf'
> atbm8830.c:(.text+0x901395): undefined reference to `__muldf3'
> atbm8830.c:(.text+0x9013a5): undefined reference to `__floatunsidf'
> atbm8830.c:(.text+0x9013b2): undefined reference to `__divdf3'
> atbm8830.c:(.text+0x9013c3): undefined reference to `__muldf3'
> atbm8830.c:(.text+0x9013cd): undefined reference to `__fixunsdfsi'
>
> ---
> ~Randy
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
This patch replace 64-bit division by do_div() macro and remove usage of
floating point variable
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the IR table is initialized by calling ir_input_init(). However,
this function doesn't return any error code, nor has a function to be called
when de-initializing the IR's.
Change the return argment to integer and make sure that each driver will
handle the error code. Also adds a function to free any resources that may
be allocating there: ir_input_free().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
