Add new ID to serial_cs.c; the CIS fimware override is available by the
manufacturer at http://www.sierrawireless.com . Remember to name the CIS
binary SW_7xx_SER.cis and to put it into /lib/firmware/
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fix up some pm_message_t types
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Vincent Sanders
When building the ARM platforms several serial drivers fail to compile
with GCC 4.01 due to extern/static ambiguity.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the new Freescale 523x processor family to ColdFire
serial driver. Also set different default baud rate for MOD5272
board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the new RBHMA4500 eval board for the TX4938. General update
from the 8250 ancestor of this driver. Replace use of deprecated
interfaces.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/segment.h varies greatly on different architectures but is clearly
deprecated. Removing all non-architecture consumers will make it easier
for us to get ride of asm/segment.h all together.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this is the last serial driver not using initcalls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <jeff@uclinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sunsu had been broken by ->stop_tx/->start_tx API changes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Base addess register for SMC 1 and 2 are never initialized. This means
that they will not work unless a bootloader already configured them.
The DPRAM already have space reserved, this patch just makes sure the base
addess register is updated correctly on initialization.
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
use schedule_timeout instead of direct call to schedule
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 2nd serial port on the MPC8560 ADS was not being configured correctly
and thus could not be used as a console. Updated the defconfig for the
board to configure the proper SCC channel for the 2nd serial port.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pre-format the IO part of the ttyS printks, and prefix them with
KERN_INFO to avoid bootsplash corruption.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems we can simply kill these dummies with this patch.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds support for setting and getting RTS / CTS via
set_mtctrl / get_mctrl functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The start_tx and stop_tx methods were passed a flag to indicate
whether the start/stop was from the tty start/stop callbacks, and
some drivers used this flag to decide whether to ask the UART to
immediately stop transmission (where the UART supports such a
feature.)
There are other cases when we wish this to occur - when CTS is
lowered, or if we change from soft to hard flow control and CTS
is inactive. In these cases, this flag was false, and we would
allow the transmitter to drain before stopping.
There is really only one case where we want to let the transmitter
drain before disabling, and that's when we run out of characters
to send.
Hence, re-jig the start_tx and stop_tx methods to eliminate this
flag, and introduce new functions for the special "disable and
allow transmitter to drain" case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
extern declaration followed by static in drivers/serial/m32r_sio.c
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMBA_PL010 is broken on arm/versatile; marked as such
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed problems so we can build with gcc-4.0.1
Signed-off-by: Peter Schaefer-Hutter <peter.schaefer-hutter@tfk-racoms.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Makes dpram allocations work
* Makes non-console UART work on both 8xx and 82xx
* Fixed whitespace in files that were touched
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Pantelis Antoniou <panto@intracom.gr>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for UARTs in MMIO space and clean up a little whitespace.
HP legacy-free ia64 machines need this.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
m8xx_cpm_hostalloc() can't rely on using the coherent DMA allocator early
on boot because the VM is not fully up yet. Change it to use the on-board
DPRAM instead.
The current code relies on the "bootmem_page" allocated by
m8xx_cpm_reset(), which must be killed.
This is done in v2.4 but has never been forward ported to v2.6.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Cc: Pantelis Antoniou <panto@intracom.gr>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the MRi PCIDS1 dual port serial card. This card is a
little controversial since it is the subject of a PCI vendor/device ID
clash. (See
http://www.ussg.iu.edu/hypermail/linux/kernel/0303.1/0516.html). I have
for now just used the hex ID 0x950a. The divisor was part calculated part
iterated, so may not be exactly correct (but works for me at all settings
between 300 - 115300 bps).
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- updates the version
- fix mixing of declarations and code. The mixing of declarations and
code displays warnings when used against RedHat RHEL4.0 distro (compiler
version is 3.4.3-22.1) and hence I separated them out.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The jsm driver uses a static number of 253. The major number 253 is a
reserved for "LOCAL/EXPERIMENTAL USE" by both char and block devices. So
take advantage of the dynamic allocation of major number by the kernel.
Signed-off-by: V. Ananda Krishnan <mansarov@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert parport_serial to use the new 8250_pci interface, converting
the table to a pciserial_board table. This also unuses the SPCI_*
definitions in serialP.h, which can now be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
