After requesting a state change, verify that the state change
actually ocurred, and the system ends up in the expected state.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The EEH event notification system passes around data that is
not needed or at least, not used properly. Stop passing this
data; get it in a more reliable fashion.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Modify routine that returns PCI slot status to wait for slot status
to become available. This is needed, as slots that are in some remote
card cage may go offline for extended periods of time. New users for
this routine in following patches.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some firmware versions will return a slot reset state of "1"
when a slot is EEH frozen. Recognize this as a state that can be
handled.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the second or higher function of a multi-function device fails
to recover, this failure is not reported upwards. Fix this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If a device driver does not have native PCI error recovery,
a hotplug error recovery will be attemped. In this case,
the device driver will not report back whether its healthy
or not; simply assume that it is.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide support for the new ibm,get-config-addr-info2 RTAS token,
whenever it is actually available.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers will attempt to perform a lot of mmio even after
an EEH event was detected. This is especially the case for fast cpu's
and PCI-E slots. Be a bit more lenient in allowing this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are multiple code patchs tht resuls in a "permanent
failure"; when examining rare events, it can be hard to see
which was taken. This patch adds printk's to assist.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the order in which pci error state is examined;
the "capabilites" is not valid if "reset state" is 5.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the declaration of flush_cache to ops.h for use by platform code.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since there is magic defined per platform in the wrapper script, the
zImage targets should depend on it.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The --no-gzip option can be passed to the wrapper so that the kernel
image is included uncompressed into the zImage. This is intended for
bootloaders where the zImage itself can be compressed, or where boot time
is considered more important than kernel image size.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add get_parent, create_node, and find_node_by_prop_value to dt_ops.
Currently only implemented by flatdevtree_misc.
Also, add a _str convenience wrapper for setprop.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Correct the apparent misspelling of "XMON" to "CONFIG_XMON".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds documenting comments to the gunzip convenience
functions added in commit ad9d2716cf.
It also removes a stray newline, and an unused global variable.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds two sysfs attributes to /sys/bus/ibmebus which can be used to
notify the ebus driver of added / removed ebus devices in the OF device
tree.
Echoing the device's location code (as found in the OFDT "ibm,loc-code"
property) into the "probe" attribute will notify ebus of addition of the
device and cause the appropriate device driver's probe function to be called
on the device.
Likewise, echoing the location code into the "remove" attribute will cause
the device to be removed from the system.
The writes will block until the respective operation has finished and return
an error code if the operation failed.
In addition, two minor tidbits are fixed:
- The fake root device used to provide a common parent for all ebus devices
is now based on device instead of of_device - it had no associated devtree
node. This saves several checks throughout the ebus driver.
- The sysfs attributes are now generated automagically by device_register()
instead of by the ibmebus code, which saves a few compiler warnings about
unused return codes.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, early_init() in setup_32.c zeroes from '_bss_start' to '_end'.
It should only zero from '__bss_start' to '__bss_stop'. This patch does that.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ft_find_node_by_prop_value() finds nodes with the specified
property/value pair.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Most of ft_get_parent() is factored out into __ft_get_parent(), which
deals only in internal node pointers. The ft_get_parent() wrapper
handles phandle conversion in both directions (previously,
ft_get_parent() did not convert its return value).
It also now returns NULL as the parent of the toplevel node, rather than
just returning the toplevel node again (which made it rather useless in
loops).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The property searching part of ft_get_prop is factored out into an
internal __ft_get_prop() which does not deal with phandles and does not
copy the property data. ft_get_prop() is then a wrapper that does the
phandle translation and copying.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a function to look up a relative, rather than absolute, path name.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When adding a property, the property name should be added to the string
table if it doesn't already exist. map_string() does that;
lookup_string() will fail instead.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the caller's pointer back to match the change in the region's start,
rather than alter a byte of the device tree's content.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ft_reorder() function may change the start of the region of interest,
so the pointer provided by the caller into that region must be fixed up
to still point to the same datum.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, if ft_get_phandle() is passed NULL it will allocate an entry
for it and return a non-NULL phandle. This patch makes it simply pass
the NULL through.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This name better reflects what the function does, which is to
look up the phandle for an internal node pointer, and add it to the
internal pointer to phandle table if not found.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up some of the open-coded data structure references by providing a
function to return a pointer to the tree's root node. This is only used
in high-level functions trying to access the root of the tree, not in
low-level code that is actually manipulating the data structure.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ops.h references NULL, so include stddef.h, so files including ops.h
don't have to.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch re-organises the way the zImage wrapper code is entered, to
allow more flexibility on platforms with unusual entry conditions.
After this patch, a platform .o file has two options:
1) It can define a _zimage_start, in which case the platform code gets
control from the very beginning of execution. In this case the
platform code is responsible for relocating the zImage if necessary,
clearing the BSS, performing any platform specific initialization, and
finally calling start() to load and enter the kernel.
2) It can define platform_init(). In this case the generic crt0.S
handles initial entry, and calls platform_init() before calling
start(). The signature of platform_init() is changed, however, to
take up to 5 parameters (in r3..r7) as they come from the platform's
initial loader, instead of a fixed set of parameters based on OF's
usage.
When using the generic crt0.S, the platform .o can optionally
supply a custom stack to use, using the BSS_STACK() macro. If this
is not supplied, the crt0.S will assume that the loader has
supplied a usable stack.
In either case, the platform code communicates information to the
generic code (specifically, a PROM pointer for OF systems, and/or an
initrd image address supplied by the bootloader) via a global
structure "loader_info".
In addition the wrapper script is rearranged to ensure that the
platform .o is always linked first. This means that platforms where
the zImage entry point is at a fixed address or offset, rather than
being encoded in the binary header can be supported using option (1).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch rewrites prep_kernel() in the zImage wrapper code to be
clearer and more flexible. Notable changes:
- Handling of the initrd image from prep_kernel() has moved
into a new prep_initrd() function.
- The address of the initrd image is now added as device tree
properties, as the kernel expects.
- We only copy a packaged initrd image to a new location if it
is in danger of being clobbered when the kernel moves to its final
location, instead of always.
- By default we decompress the kernel directly to address 0,
instead of requiring it to relocate itself. Platforms (such as OF)
where doing this could clobber still-live firmware data structures can
override the vmlinux_alloc hook to provide an alternate place to
decompress the kernel.
- We no longer pass lots of information between functions in
global variables.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, arch/powerpc/boot/main.c includes a gunzip() function
which is a convenient wrapper around zlib. However, it doesn't
conveniently allow decompressing part of an image to one location,
then the remainder to a different address.
This patch adds a new set of more flexible convenience wrappers around
zlib, moving them to their own file, gunzip_util.c, in the process.
These wrappers allow decompressing sections of the compressed image to
different locations. In addition, they transparently handle
uncompressed data, avoiding special case code to handle uncompressed
vmlinux images.
The patch also converts main.c to use the new wrappers, using the new
flexibility to avoid decompressing the vmlinux's ELF header twice as
we did previously. That in turn means we avoid extending our
allocations for the vmlinux to allow space for the extra copy of the
ELF header.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove fixed setting of ROOT_DEV for 7448HPC2 platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This will allow us to build without PCI easier.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are many adapters which can not handle DMAing acrosss any 4 GB
boundary. For instance the latest Emulex adapters.
This normally is not an issue as firmware gives us dma-windows under
4gigs. However, some of the new System-P boxes have dma-windows above
4gigs, and this present a problem.
I propose fixing it in the IOMMU allocation instead of making each
driver protect against it as it is more efficient, and won't require
changing every driver which has not considered this issue.
This patch checks to see if the mapping spans a 4 gig boundary, and if
it does, retries the allocation. It tries the next allocation at the
start of the crossed 4 gig boundary.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The #cpus property is unused and undocumented and is therefore
being removed.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove some redundant isync instructions.
enable_64b_mode() already does an isync, so there is no need to do it again.
Signed-off-by: MOKUNO, Masakazu <mokuno@sm.sony.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add missing checks to PS3 specific drivers ps3av and sys-manager to verify that
we are actually running on a PS3 (pointed out by Arnd).
Correct existing checks in other subsystems/drivers to return -ENODEV instead
of zero.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
