This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On newer Asus boards the "upper" limit of a sensor is encoded as
delta from the "lower" limit. Fix the driver to correctly handle
this case.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Alex Macfarlane Smith <nospam@archifishal.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SMSC LPC47M233 and LPC47M292 chips have the same device ID but
are not compatible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add support for the ADC controller on the S3C series of processors to
drivers/hwmon for use with hardware monitoring systems.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Switch the AB9, AB9 QuadQT and IX38 QuadGT over from port
probing to the preferred DMI probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: dan <dan@deeog.com>
Tested-by: Nygel Lyndley <nygel.lyndley@gmail.com>
Tested-by: Dmitriy Fedchenko <dmitriy-fedc@yandex.ru>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add omitted update_lock to one switch/case in set_div.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
The LIS302DL accelerometer chip has a 'click' feature which can be used to
detect sudden motion on any of the three axis. Configuration data is
passed via spi platform_data and no action is taken if that's not
specified, so it won't harm any existing platform.
To make the configuration effective, the IRQ lines need to be set up
appropriately. This patch also adds a way to do that from board support
code.
The DD_* definitions were factored out to an own enum because they are
specific to LIS3LV02D devices.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Separate the 6710 and 6715, and set the right axis information for the
6715.
Reported-by: Isaac702 <isaac702@gmail.com>
Add the 6930.
Reported-by: Christian Weidle <slateroni@gmail.com>
Add the 2710.
Reported-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that there is no need to hookup on the open/close of the joystick,
it's possible to use the simplified interface input_polled_device, instead
of creating our own kthread.
[randy.dunlap@oracle.com: fix Kconfig]
[randy.dunlap@oracle.com: fix Kconfig some more]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After measurement on my laptop, it seems that turning off the device does
not bring any energy saving (within 0.1W precision). So let's keep the
device always on. It simplifies the code, and it avoids the problem of
reading a wrong value sometimes just after turning the device on.
Moreover, since commit ef2cfc790b had been
too zealous, the device was actually never turned off anyway. This patch
also restores the damages done by this commit concerning the
initialisation/poweroff.
Also do more clean up with the usage of the lis3_dev global variable.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Can only unregister the misc device if it was registered before. Also
remove debugging messages, which in addition were not properly formated.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the alarm flags provided by the MAX6650/MAX6651 fan-speed regulator
and monitor chips via sysfs.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the hwmon part of the Fintek F71858FG superio IC to the
f71882fg driver. Many thanks to Jelle de Jong for lending me a motherboard
with this superio on it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on f71852fg support I noticed that the f8000 sysfs attr
table was missing entries for temp#_fault, which the f8000 does have and
which we were already reading.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We depend up on the pwm_enable register (0x96) not containing any reserved
settings in various places. We were already checking to make sure there
were no reserved settings in the register for the f71862fg, this patch adds
the same checking for the f8000, while at it it also moves the code to
a more apropriate place so we don't need to check if the fan/pwm part
of the IC is enabled twice.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently we are using separate per model sysfs attr for the 3th pwm, because
the 3th pwm of the f8000 only has automatic mode and not manual mode. Doing
things this way was getting in the way for adding f71858fg support, so this
patch makes the pwm attr identical for all models, and instead adds a check
to store_pwm_enable() disallowing setting the 3th pwm to manual mode
on a f8000 IC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MSI MS-7031 is based on an ATI IXP300 south bridge. On this south
bridge, accessible I/O ports must be enabled explicitly. Unfortunately
the BIOS forgets to enable access to the hardware monitoring chip I/O
ports, so hardware monitoring fails.
Add a quirk enabling access to the required ports (0x295-0x296). This
is exactly what MSI's own hardware monitoring application is doing, so
it has to be the right way.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the new incarnation of the Winbond/Nuvoton W83627DHG
chip known as W83627DHG-P. It is basically the same as the original
W83627DHG with an additional automatic can speed control mode (not
supported by the driver yet.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Madhu <madhu.chinakonda@gmail.com>
This adds support for TI's TMP411 sensor chip.
Preliminary support were done by Gabriel Konat, Sander Leget and
Wouter Willems. The chip is compatible with TI's TMP401 sensor
chip. It has additional support for historical minimun/maximum
measurements.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a new hwmon driver for TI's TMP401 temperature sensor IC. This driver
was written on behalf of an embedded systems vendor under the
Linux driver project.
It has been tested using a TI TMP401 sample attached to a i2c-tiny-usb adapter.
Which was provided by Till Harbaum, many thanks to him for this!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enable auto-probing for the HC10 blade and amend the supported system
list.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make sure __devexit and devexit_p() match in all hwmon drivers.
Suggested by a similar fix from Mike Frysinger.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 360782dde0 (hwmon: (w83781d) Stop
abusing struct i2c_client for ISA devices) broke W83782D support for
devices connected on the ISA bus. You will hit a NULL pointer
dereference as soon as you read any device attribute. Other devices,
and W83782D devices on the SMBus, aren't affected.
Reported-by: Michel Abraham
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Abraham
atk_sensor_type is only used when DEBUG is defined.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf
These sensors communicate over a 2 wire bus running a device specific
protocol. The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available. This is handled by
an interrupt that is disabled under all other conditions.
I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!
Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem. If not it should be provided in the
platform data.
I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Matthew Palmer <mpalmer@debian.org>
Signed-off-by: Laurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.
There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).
Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy i2c binding model is going away really soon now, so convert
the lm95241 driver to the new binding model or it will break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Make use of the new abstraction layer and add a new transport layer for
spi. Works fine on a PXA based board.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This solves the dependency between lis3lv02d.[ch] and ACPI specific
methods. It introduces a ->bus_priv pointer to the device struct which is
casted to 'struct acpi_device' in the ACIP layer. Changed hp_accel.c
accordingly.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move lis3lv02d_init_device() down so that the forward declaration of
lis3lv02d_add_fs() becomes unnecessary.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a laptop HP Compaq 8710W, I compiled into my kernel the LIS3LV02DL
and HP_ACCEL module drivers. While loading it cannot recognize the laptop
model, so i am sending the necessary information to update the database of
axis orientations.
>When the laptop is horizontal the position reported is about 0 for X and Y
>and a positive value for Z
Yes, it is about 0,0,1000, the actual reading says: (-17,-26,1018);
> If the left side is elevated, X increases (becomes positive)
Yes, X goes toward to positive 1000.
>If the front side (where the touchpad is) is elevated, Y decreases (becomes negative)
No, Y goes toward to positive 1000.
>If the laptop is put upside-down, Z becomes negative
Yes, the laptop on a table Z gives 1000, and if upsidedown the Z reads
-1000.
So in few words the Y axis is inverted.
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two more laptops to whitelist.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.
I have tested the driver with my board, and it appears to work fine. With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power. With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power. I'm not drawing any current at the
moment, so this is reasonable. The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.
I didn't attempt to support changing any of the chip's settings or
enabling the FET. I'm not sure even how to do that and still fit within
the hwmon framework. :)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An hwmon driver for the National Semiconductor LM95241 triple temperature
sensors chip
Signed-off-by: Davide Rizzo <elpa-rizzo@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Andrew noted, adev is pretty poor name for symbol being exported.
Rename it to lis3.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Cc: <Quoc.Pham@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many thanks to Fujitsu Siemens Computers for providing docs and a
machine to test the driver on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.
If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
The pin for in6 and temp3 is shared on the W83667HG, so only one of
these features can be supported on any given system. Let the driver
select which one depending on the temp3 disabled bit.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.
At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use positive logic for fan pin variables (variable is set if pin is
used for fan), instead of negative logic which is error prone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Gong Jun <JGong@nuvoton.com>
