This removes a WARN_ON that is responsible for the following koops:
http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample
The comment in the patch describes why it's safe to simply remove
the check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This updates the beacon template code to upload both templates,
if we never uploaded one before.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some TX/RX related locking issues.
With this patch applied, some of the PHY transmission errors are fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the initialization of the PHY TX control words in
shared memory. These control words are used for management frames
like beacons.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes beacon updating in the bottomhalf.
In case the device is busy, we will defer to later in the IRQ handler.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are some beaconing related fixes. Basically it prevents
the card from triggering the beacon IRQ over and over again.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some timings for pre-TBTT and synthetic PU.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds PIO support back (D'oh!) for PCMCIA devices.
This is a complete rewrite of the old PIO code. It does actually work
and we get reasonable performance out of it on a modern machine.
On a PowerBook G4 I get a few MBit for TX and a few more for RX.
So it doesn't work as well as DMA (of course), but it's a _lot_ faster
than the old PIO code (only got a few kBit with that).
The limiting factor is the host CPU speed. So it will generate 100%
CPU usage when the network interface is heavily loaded. A voluntary preemption
point in the RX path makes sure Desktop Latency isn't hurt.
PIO is needed for 16bit PCMCIA devices, as we really don't want to poke with
the braindead DMA mechanisms on PCMCIA sockets. Additionally, not all
PCMCIA sockets do actually support DMA in 16bit mode (mine doesn't).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename the DMA ring pointers to have more descriptive and standard
names. Also remove the 6th unused TX ring. We can add it back later,
if we need it. The unused TX-status rx-ring is also removed, as that's
only used by legacy devices not supported by this driver anyway.
This is no functional change, except less memory allocation for
the removed rings.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds QOS support to the b43 driver.
QOS can be disabled on driver level with a module parameter for debugging purposes.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the high 16 bits of the hostflags.
No functional change.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes bandswitching for the new mac80211 band API.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds printk messages with basic information about the driver being loaded.
This information includes a summary of the compiled-in features, which
simplifies bug-reporting and debugging a lot.
Also a firmware ID is printed. This is a unique identifier blob for a specific
version of the firmware. This ID is attached to a specific version of the firmware
blob in b43-fwcutter (see fwcutter git).
This helps users to select the right firmware for their device.
This also makes it possible to use automated scripts to fetch and extract the right
firmware for the driver. (the script will grep the .ko for the "Firmware-ID: xxx" string.
While the driver might still support other versions of the firmware for backward
compatibility, this will always print out the officially supported version, which
people _should_ use.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the b43 driver to avoid deadlocking suspend and resume, which happens
as a result of attempting to unregister device objects locked by the PM core
during suspend/resume cycles. Also, make it use a suspend-safe method of
unregistering device object in the resume error path.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We must also store the ID string (filename) for the cached firmware blobs
and verify that we really have the right firmware cached before using it.
If we don't have the right fw cached, we must free it and request the
correct blobs.
This fixes bandswitch on A/B/G multi-PHY devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This queues frames flagged as "send after DTIM" by mac80211
on the special multicast queue. The firmware will take care
to send the packet after the DTIM.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes uploading of the beacon data and writing of the
TIM and DTIM offsets.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a sparse warning about weird locking.
The spinlock is not needed, so simply remove it.
This also adds some sanity checks to the PHY and radio locking
to protect against recursive locking.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some definitions for the MAC Control register
and uses them.
This basically is no functional change.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove b43 PIO support.
DMA works well on all supported devices. There's no reason to use PIO.
Additionally, new devices don't support PIO in hardware anymore.
b43 PIO support is dead and unused code.
After applying this patch please do
git rm drivers/net/wireless/b43/pio.h
git rm drivers/net/wireless/b43/pio.c
to remove the main PIO support code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes chip access validation for newer devices
(4318 and up, I think)
This patch fixes probing of a PCMCIA based 4318 device.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit f04b3787bbce4567e28069a9ec97dcd804626ac7 introduced
a regression for the ofdmtable writing.
It incorrectly removed the writing of the high 16bits for
a 32bit table write and initialized the direction identifier
too late.
This patch does also some cleanups to make the code much more
readable and adds a few comments, so non rocket scientists are
also able to understand what this address caching is all about.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the hardware on too many PHY TX errors. A thousand PHY TX errors
per 15 seconds means we won't be able to recover for sure.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When monitor mode is enabled, this will make b43 read out the
full 64-bit MAC time from the chip for each received packet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite and sync A PHY initialization with specs, thus allowing for further
work to be done on 802.11a support. Note that A PHY initialization involves
G PHYs as well.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the parsing of the RX data header channel field.
The current code parses the header incorrectly and passes a wrong
channel number and frequency for each frame to mac80211.
The FIXMEs added by this patch don't matter for now as the code
where they live won't get executed anyway. They will be fixed later.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds full support for the RFKILL button and
the RFKILL LED trigger.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drive the LEDs through the generic LED triggers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
