It fixes a bug in zfcp which provokes a race
in scsi_scan.c. Finally this can lead to an Oops like:
kernel BUG at fs/sysfs/symlink.c:87!
Correctly set this_id for the host. Otherwise we provoke
a race between scsi_target_reap_work and concurrent
scsi_add_device.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Revert dasd eer module until we have a common understanding of how the
interface should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When using the dasd diag discipline, the base discipline module (eckd or fba)
can be unloaded, even though the dasd driver requires both discipline modules
(base and diag) to work correctly.
Implement reference counting for both base and diag discipline modules in
order to fix this.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using FCP devices with V=V support, the input queue stalled when CCQ 97 had
been returned in qdio_do_eqbs. When this happen we have to reissue the eqbs
instruction.
Another bug was when V=V was enabled we checked if hardware has SIGA-sync
support. If not we returned with 0 from tiqdio_is_inbound_q_done. Thus qdio
lost initiative on FCP devices and input queue stalled. Running devices in
V=V there is no SIGA-sync support but nevertheless we have to process
tiqdio_is_inbound_q_done either.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If __ccw_device_disband_start() fails to initiate disbanding, it should finish
with ccw_device_disband_done() (which leaves the device in offline state)
instead of ccw_device_verify_done() (which leaves the device in online state).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[patch 2/2] s390: some qeth driver fixes
From: Frank Pavlic <fpavlic@de.ibm.com>
- fixed kernel panic when using EDDP support in Layer 2 mode
- NULL pointer exception in qeth_set_offline fixed.
- setting EDDP in Layer 2 mode did not set NETIF_F_(SG/TSO)
flags when device became online.
- use sscanf for parsing and converting IPv4 addresses
from string to __u8 values.
- qeth_string_to_ipaddr6 fixed. in case of double colon
the converted IPv6 address out from the string was not correct
in previous implementation.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth.h | 112 +++++++++++++++++++++++++-----------------------------------
qeth_eddp.c | 11 ++++-
qeth_main.c | 17 +++------
3 files changed, 63 insertions(+), 77 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 1/2] s390: lcs performance enhancements
From: Klaus Wacker <kdwacker@de.ibm.com>
- When flood pinging (with large packet size) an LCS device,
about 90 % of all packets are dropped by driver.
- increased number of lcs IO buffers to 32.
- use netif_stop_queue/netif_wake_queue in lcs_start_xmit routine
- don't lock the whole xmit routine but just the piece of code where
tx_buffer is touched.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
lcs.c | 31 +++++++++++++++++--------------
lcs.h | 2 +-
2 files changed, 18 insertions(+), 15 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Flush workqueue of a scsi host after a remote port for that host
is registered at the fc transport class. Otherwise immediate
registration of a scsi device on that host is racy.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Avoid access to old fsf_requests if device reset is logged.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove endless polling for replug of the local link. Just wait for
link up notification.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove all remainders of obsolete zfcp adapter attributes physical_wwpn and
physical_s_id.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When the sclp interface takes very long to serve a request, the sclp core
driver will report a failed request to the sclp tty driver even though the
request is still being processed by the sclp interface. Eventually the sclp
interface completes the request and updates some fields in the request buffer
which leads to a corrupted tty pages list. The next time function
sclp_tty_write_room is called, the corrupted list will be traversed, resulting
in an oops.
To avoid this remove the busy retry limit and increase retry intervals.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix locking in __chp_add() and s390_subchannel_remove_chpid(): Need to
disable/enable because they are always called from a thread (and not
directly from a machine check...)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The DASD extended error reporting is a facility that allows to get detailed
information about certain problems in the DASD I/O. This information can be
used to implement fail-over applications that can recover these problems.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a missing return check from strnlen_user and fixes a off-by-one when
terminating the string with zero.
Signed-off-by: Davi Arnaut <davi.arnaut@gmail.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix modalias for ccw devices: cu_type should be in capitals as well.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The sleep_on function clears a running cqr without waiting for the related
interrupt. This can lead to a panic at the time the interrupt is processed
because the related memory might already be freed. Wait for clear-interrupt
and de-queue cqr prior to return.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The open_count is increased for every opener, that includes the blkdev_get in
dasd_scan_partitions. This tampers the open_count in BIODASDINFO. Hide the
internal open from user-space.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The return code of ccw_device_probe_console() is not properly handled. It
should only return a valid ccw device pointer or a error value converted by
ERR_PTR. Fix the console driver code to check with IS_ERR instead against
NULL.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove useless s390 define from hangcheck-timer, remove wrong definition of a
TOD second and other s390 ifdefs. Use monotonic_clock instead.
Add hangcheck-timer option, copied from drivers/char/Kconfig. This is ugly
but unless we have a big Kconfig cleanup we cannot include
drivers/char/Kconfig...
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove all CVS generated information like e.g. revision IDs from
drivers/s390 and include/asm-s390 (none present in arch/s390).
- Add newline at end of arch/s390/lib/Makefile to avoid diff message.
Acked-by: Andreas Herrmann <aherrman@de.ibm.com>
Acked-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The QUEUE_ORDERED_* numbers got renumbered and by accident the dasd driver
was changed to use QUEUE_ORDERED_DRAIN instead of QUEUE_ORDERED_TAG.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The chps[] array in struct channel_subsystem is one too short; therefore the
code doesn't realize the chpid ff is already known. When several devices on
chpid ff become available, the message "new_channel_path: could not register
ff" is displayed for every device but the first one.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the missing third argument to the blk_queue_ordered call and use the
constant QUEUE_ORDERED_DRAIN instead of "1".
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replaced zfcp adapter attributes with fc_host attributes:
fc_topology by port_type, physical_wwpn by permanent_port_name.
Make use of fc_host attribute supported_speeds.
Removed zfcp adapter attribute physical_s_id.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added host stats, removed superfluous get_starget_ functions,
removed some attributes from zfcp specific sysfs tree (e.g.
scsi_host_no, scsi_lun, wwnn and d_id).
Host stats are given for the physical adapter port not for the
virtual adapter. Reset stats is implemented in the device driver.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Handle unsolicited adapter status that informs about loss of
previous unsolicited status notification(s).
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The following patch converts css_bus_type and ccw_bus_type to use
the new bus_type methods.
Signed-off-by: Cornelia Huck <huckc@de.ibm.com>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The API and code have been through various bits of initial review by
serial driver people but they definitely need to live somewhere for a
while so the unconverted drivers can get knocked into shape, existing
drivers that have been updated can be better tuned and bugs whacked out.
This replaces the tty flip buffers with kmalloc objects in rings. In the
normal situation for an IRQ driven serial port at typical speeds the
behaviour is pretty much the same, two buffers end up allocated and the
kernel cycles between them as before.
When there are delays or at high speed we now behave far better as the
buffer pool can grow a bit rather than lose characters. This also means
that we can operate at higher speeds reliably.
For drivers that receive characters in blocks (DMA based, USB and
especially virtualisation) the layer allows a lot of driver specific
code that works around the tty layer with private secondary queues to be
removed. The IBM folks need this sort of layer, the smart serial port
people do, the virtualisers do (because a virtualised tty typically
operates at infinite speed rather than emulating 9600 baud).
Finally many drivers had invalid and unsafe attempts to avoid buffer
overflows by directly invoking tty methods extracted out of the innards
of work queue structs. These are no longer needed and all go away. That
fixes various random hangs with serial ports on overflow.
The other change in here is to optimise the receive_room path that is
used by some callers. It turns out that only one ldisc uses receive room
except asa constant and it updates it far far less than the value is
read. We thus make it a variable not a function call.
I expect the code to contain bugs due to the size alone but I'll be
watching and squashing them and feeding out new patches as it goes.
Because the buffers now dynamically expand you should only run out of
buffering when the kernel runs out of memory for real. That means a lot of
the horrible hacks high performance drivers used to do just aren't needed any
more.
Description:
tty_insert_flip_char is an old API and continues to work as before, as does
tty_flip_buffer_push() [this is why many drivers dont need modification]. It
does now also return the number of chars inserted
There are also
tty_buffer_request_room(tty, len)
which asks for a buffer block of the length requested and returns the space
found. This improves efficiency with hardware that knows how much to
transfer.
and tty_insert_flip_string_flags(tty, str, flags, len)
to insert a string of characters and flags
For a smart interface the usual code is
len = tty_request_buffer_room(tty, amount_hardware_says);
tty_insert_flip_string(tty, buffer_from_card, len);
More description!
At the moment tty buffers are attached directly to the tty. This is causing a
lot of the problems related to tty layer locking, also problems at high speed
and also with bursty data (such as occurs in virtualised environments)
I'm working on ripping out the flip buffers and replacing them with a pool of
dynamically allocated buffers. This allows both for old style "byte I/O"
devices and also helps virtualisation and smart devices where large blocks of
data suddenely materialise and need storing.
So far so good. Lots of drivers reference tty->flip.*. Several of them also
call directly and unsafely into function pointers it provides. This will all
break. Most drivers can use tty_insert_flip_char which can be kept as an API
but others need more.
At the moment I've added the following interfaces, if people think more will
be needed now is a good time to say
int tty_buffer_request_room(tty, size)
Try and ensure at least size bytes are available, returns actual room (may be
zero). At the moment it just uses the flipbuf space but that will change.
Repeated calls without characters being added are not cumulative. (ie if you
call it with 1, 1, 1, and then 4 you'll have four characters of space. The
other functions will also try and grow buffers in future but this will be a
more efficient way when you know block sizes.
int tty_insert_flip_char(tty, ch, flag)
As before insert a character if there is room. Now returns 1 for success, 0
for failure.
int tty_insert_flip_string(tty, str, len)
Insert a block of non error characters. Returns the number inserted.
int tty_prepare_flip_string(tty, strptr, len)
Adjust the buffer to allow len characters to be added. Returns a buffer
pointer in strptr and the length available. This allows for hardware that
needs to use functions like insl or mencpy_fromio.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days ioctl32.h is only used for communication of fs/compat.c and
fs/compat_ioctl.c and doesn't contain anything of interest to drivers.
Remove inclusion in various drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a compat_ioctl method to the dasd driver so the last entries in
arch/s390/kernel/compat_ioctl.c can go away. Unlike the previous attempt this
one does not replace the ioctl method with an unlocked_ioctl method so that
the ioctl_by_bdev calls in s390 partition code continue to work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only own ioctl, TAPE390_DISPLAY, is compat_clean, everything else is
routed through common translation code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Again easy because all ioctls are compat clean.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the sclp_cpi module is loaded on a system which does not support the
required SCLP call (e.g. on z/VM), ENOSUPP is returned to user space. The
correct return value is EOPNOTSUPP.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Use kzalloc() in blacklist.c.
- Kill unwanted casts in blacklist.c.
- Provide release function for struct channel_subsystem.
Signed-off-by: Cornelia Huck <huckc@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for multiple subchannel sets. Works with arbitrary devices in
subchannel set 1 and is transparent to device drivers. Although currently
only two subchannel sets are available, this will work with the architectured
maximum number of subchannel sets as well.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert /proc/cio_ignore to a sequential file. This makes multiple subchannel
sets support easier.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
struct channel_subsystem encapsulates several per channel subsystem
properties, like status of chpids or the global path group id.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_subchannel() is an iterator calling a function for every possible
subchannel id until non-zero is returned. Convert the current iterating
functions to it.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces a struct subchannel_id containing the subchannel number
(formerly referred to as "irq") and switches code formerly relying on the
subchannel number over to it.
While we're touching inline assemblies anyway, make sure they have correct
memory constraints.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New feature V=V qdio pass-through.
QDIO and HiperSockets processing in z/VM V=V guest environments (as well as
V=R with z/VM running in LPAR mode) requires shadowing of all QDIO
architecture queue elements. Especially the shadowing of SBALs and SLSBs
structures in the hypervisor, and the need to issue SIGA SYNC operations to
observe state changes, eventually causes significant CPU processing overhead
in the hypervisor.
The QDIO pass-through support for V=V guests avoids the shadowing of SBALs and
SLSBs. This significantly reduces the hypervisor overhead for QDIO based I/O.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To properly support multipath-failover handling, the linux block layer has
introduced a special request flag, 'REQ_FAILFAST'. This flag is now used to
return requests immediately in case the device is not operational.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IOCTL BIODASDPRRD had no return code for 'profiling is inactive' and
therefore tunedasd wrote misleading message for request-counter = 0.
Introduce return-code EIO for inactive profiling.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extract the s390_root_dev_* functions from the common I/O layer as they are
also used by non-ccw device drivers.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we receive path not operational indications (pnom in pmcw nonzero), we
switch off those paths. To catch them becoming available again, we have to
recalculate the lpm from the pmcw each time we start path verification.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Moved definition of CMS volume label to vtoc.h and modify partitions/ibm.c to
use this volume label definition instead of anonymous array.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins <hugh@veritas.com>
Fix the broken atomic_cmpxchg primitive. Add atomic_sub_and_test,
atomic64_sub_return, atomic64_sub_and_test, atomic64_cmpxchg,
atomic64_add_unless and atomic64_inc_not_zero. Replace old style
atomic_compare_and_swap by atomic_cmpxchg. Shorten the whole header by
defining most primitives with the two inline functions atomic_add_return and
atomic_sub_return.
In addition this patch contains the s390 related fixes of Hugh's "mm: fill
arch atomic64 gaps" patch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add @uptodate argument to end_that_request_last() and @error
to rq_end_io_fn(). there's no generic way to pass error code
to request completion function, making generic error handling
of non-fs request difficult (rq->errors is driver-specific and
each driver uses it differently). this patch adds @uptodate
to end_that_request_last() and @error to rq_end_io_fn().
for fs requests, this doesn't really matter, so just using the
same uptodate argument used in the last call to
end_that_request_first() should suffice. imho, this can also
help the generic command-carrying request jens is working on.
Signed-off-by: tejun heo <htejun@gmail.com>
Signed-Off-By: Jens Axboe <axboe@suse.de>
The first of these changes s/hotplug/uevent/ was needed to
compile sn2_defconfig (ia64/sn). The other three files
changed are blind changes of all remaining bus_type.hotplug
references I could find to bus_type.uevent.
This patch attempts to finish similar changes made in the
gregkh-driver-kill-hotplug-word-from-driver-core Nov 22 patch.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It makes zero sense to have hotplug, but not the netlink
events enabled today. Remove this option and merge the
kobject_uevent.h header into the kobject.h header file.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[patch 1/3] s390: some minor qeth driver fixes
From: Frank Pavlic <pavlic@de.ibm.com>
- let's have just one function for both ,input and output queue
to check qdio errors
- add /proc/s390dbf/qeth_qerr entries for outbound processing
- check removed for layer2 device in qeth_add_multicast_ipv6
- NULL pointer dereference with bonding and VLAN device fixed
- minimum length check for portname fixed
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
qeth_main.c | 42 +++++++++++++++++++++---------------------
qeth_sys.c | 6 +++---
2 files changed, 24 insertions(+), 24 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change return code in slave_alloc to avoid irritating error message from
scsi_alloc_sdev() when scsi stack tries target scan.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't check link down payload in case of firmware update.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed various problems in opening sequence of adapters which was previously
changed with NPIV support:
o corrected handling when exchange port data function is not supported,
otherwise adapters on z900 cannot be opened anymore
o corrected setup of timer for exchange port data if called from error
recovery
o corrected check of return code of exchange config data
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move initialization of locks and lists to adapter allocation function.
Otherwise we might end up with some uninitialized locks, like e.g. the
erp locks which only will be inititialized if an error recovery thread
for an adapter will be started.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add the missing NULL argument to the class_device_create calls.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[patch 6/7] s390: introduce guestLan sniffer support in qeth
From: Peter Tiedemann <ptiedem@de.ibm.com>
- introduce guestLan sniffer support in qeth
feature allows a linux in a virtual machine
guest to become a network LAN sniffer,
monitoring and recording the networking traffic
within an entire guestLan.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth.h | 2 +
qeth_main.c | 93 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
qeth_mpc.h | 11 ++++---
3 files changed, 102 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 5/7] s390: fix recovery failure of non-guestLAN devices
From: Frank Pavlic <fpavlic@de.ibm.com>
- Recovery of non-guestLAN Layer 2 device failed due to
trying to register the real MAC address we got from
the READ_MAC adapter parameters command.
We have to keep the "old" MAC address when we process
the reply of a READ_MAC.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth.h | 12 ++++++------
qeth_main.c | 27 ++++++++++++++++-----------
2 files changed, 22 insertions(+), 17 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 4/7] s390: some more qeth fixes
From: Frank Pavlic <fpavlic@de.ibm.com>
From: Peter Tiedemann <ptiedem@de.ibm.com>
- possible race on list fixed by reset
list processing after every operation
- traffic hang fixed
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 11 +++++++----
1 files changed, 7 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 3/7] s390: qeth multicast address registration fixed
From: Klaus Dieter Wacker <kdwacker@de.ibm.com>
- when running in Layer2 mode we don't have to register
the multicast IP address but only group mac address.
Therefore for Layer 2 devices it is enough to go
through dev->mc_list list and register these entries.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 106 +++++++++++++++++++++++++++++++++++++++++++++---------------
1 files changed, 80 insertions(+), 26 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 2/7] s390: minor modification in qeth layer2 code
From: Frank Pavlic <fpavlic@de.ibm.com>
- use qeth_layer2_send_setdelvlan_cb to check
return code of a SET/DELVLAN IP Assist command.
It fits better in qeth's design and mechanism of IP Assist
command handling.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 40 ++++++++++++++++++++++++++--------------
1 files changed, 26 insertions(+), 14 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/s390/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/s390/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Cornelia Huck <cohuck@de.ibm.com>
Acked-by: Stefan Bader <Stefan.Bader@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If vmcp is interrupted by a signal the vmcp command buffer is not freed.
Found by Pete Zaitcev.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Access to FBA disks via DIAG fails for block sizes > 512 byte. The device
analysis code of the DIAG discipline does not properly initialize the DIAG250
device environment after completion of the analysis. This results in VM only
serving 512 bytes per block I/O request whereas Linux expects larger block
sizes. Add proper device environment setup to end of analysis code.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Future versions of gcc may remove initialization code for control blocks used
by the diag250 inline assembly due to incompletely specified constraints.
This may lead to erratic behavior. Fix the diag250 inline assembly
constraints.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the interface for setting ccw group devices on-/offline consistent with
that for ccw devices: Check if the device driver provided a set_{on,off}line
function and just set the device on-/offline if not.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch exports modalias for ccw devices.
So you can do:
modprobe `echo /sys/device/path_to_device/modalias`
and the proper driver will automatically be loaded by userspace.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix fullscreen view of the 3270 device driver.
Signed-off-by: Richard Hitt <rbh00@utsglobal.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Search for a disconnect ccw_device on the ccw bus rather than on the css
bus (was a typo in patch I did for the klist conversion). A cast to an
embedding ccw_device from an embedded device in a struct subchannel will
lead us to oopses.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces new feature in qeth:
qeth enhancement provides the device driver support for
the Communication Controller for Linux on System z9 and zSeries
(CCL), which is software that enables running the Network Control
Program (NCP) on a zSeries machine. The OSA CDLC support is based
on a new IBM mainframe CHPID type called Open Systems Adaper for
NCP (OSN). In case of OSN qeth communicates with the type-OSN
OSA-card on one hand, and with the CCL-kernel-component Network
Device Handler (NDH) on the other.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Peter Tiedemann <ptiedem@de.ibm.com>
From: Frank Pavlic <pavlic@de.ibm.com>
minor qeth fixes:
- free old skb in qeth_realloc_headroom after duplicating skb
- disable IPV6 support for Hipersockets devices
- call ccw_device_set_offline on every channel regardless
of the return value of the prior ccw_device_set_offline calls
- allocate qdio structures in DMA-area
- schedule recovery of appropriate card
when cable has been inserted again.
- add missing initialization of card->lock
- write sequence number in skb->cb for SNA protocol which
requires strictly serialized packets.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
qeth.h | 2 ++
qeth_main.c | 37 +++++++++++++++++--------------------
2 files changed, 19 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.
1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().
There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition. I've marked it as such so that we remember to fix it.
This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
add the helper and use it instead of open coding the klist_node_attached() check
(which is a layering violation IMHO)
idea by Alan Stern.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this patch adds some fc host attributes and removes its equivalents
from the zfcp_adapter structure and zfcp specific sysfs subtree.
Furthermore it removes superfluous calls to fc_remort_port_delete when
an adapter is set offline because rports will be removed by
fc_remove_host anyway.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
N_Port ID Virtualization (NPIV) allows a single FCP port to appear as
multiple, distinct ports providing separate port identification. NPIV
is supported by FC HBAs on System z9. zfcp was adapted to support this
new feature.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Debug features (DBFs) els_dbf, cmd_dbf and abt_dbf were removed and
san_dbf, hba_dbf and scsi_dbf were introduced. The erp_dbf did not
change.
The new traces improve debugging of problems with zfcp, scsi-stack,
multipath and hardware in the SAN. san_dbf traces things like ELS and
CT commands, hba_dbf saves HBA specific information of requests, and
scsi_dbf saves FCP and SCSI specific information of requests. Common
to all new DBFs is that they provide a so called structured view. This
significantly improves readability of the traces.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
o union zfcp_req_data removed
o increment unit refcount when processing FCP commands
(This fixes a theoretical race: When all scsi commands of a unit
are aborted and the scsi_device is removed then the unit could be
removed before all fsf_requests of that unit are completely processed.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
o always use locking when changing erp_action lists,
o avoid escalation to ERP_ACTION_REOPEN_PORT_FORCED if erp_action is
still in use for ERP_ACTION_REOPEN_PORT
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Got confused with the crypto update. The last patch added a call to
destroy_workqueue() for a non-existent workqueue with the comment "Remove
device workqueue on module unload". This is nonsense. Remove the offending
hunk again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Calculate correct size for bl_dev array. It should be 8KB instead of 512KB
for 2^16 bits.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[patch 4/4] s390: qeth driver fixes .
From: Frank Pavlic <pavlic@de.ibm.com>
- Clear read channel first prior to using ccw_device_set_offline.
- use QETH_DBF_TEXT instead of QETH_DBF_SPRINTF
- invoke qeth_halt_channel and qeth_clear_channel for all channels,
even if halt/clear for one of the channel fails.
- enable qeth_arp_query function for GuestLAN devices
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
qeth.h | 2 -
qeth_main.c | 106 +++++++++++++++++++++++++-----------------------------------
qeth_sys.c | 11 +++---
3 files changed, 53 insertions(+), 66 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff,
I'm sorry seems that they have not been sent out either ...
ok here they come ...
[patch 3/4] s390: TSO related fixes in qeth driver
From: Frank Pavlic <pavlic@de.ibm.com>
TSO related fixes :
- changing value of large_send attribute while network traffic
is running caused program check and thus device recovery.
- Due to hardware restriction discard packet when it exceeds 60K
otherwise qeth will cause program checks and thus traffic stall
when trying to send such huge packets.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
qeth.h | 4 ++--
qeth_main.c | 33 +++++++++++++++++++++------------
qeth_sys.c | 10 +++-------
3 files changed, 26 insertions(+), 21 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff,
sorry if I have flooded your inbox, I had some problems with the
mail server here yesterday, but it seems to be fixed ...
Ok patch 3-4 have no dependencies on patch 2 since only qeth driver is
affected.Thus I have made a new patch 2 for ctc driver.
Thank you .
[patch 2/4] s390: ctc driver fixes
From: Peter Tiedemann <ptiedem@de.ibm.com>
- race condition fixed
- minor cleanup
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
ctcmain.c | 41 ++++++++++++++++++++++-------------------
1 files changed, 22 insertions(+), 19 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix reboot with a disconnected 3270 console.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Common i/o layer changes:
- Collect the irb at the correct subchannel when waiting for the clear
interrupt during subchannel cleaning befor reIPL - don't stop at the first
interrupt that comes in.
- Change "extern __inline__" to "static inline".
- Remove unneeded qdio includes.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for diag 250 access to dasd devices for 64 bit kernels. In
addition fix detach/attach for diag disks. The VM control block needs to get
recreated by a call to mdsk_init_io.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reintroduce a read-only copy of the devmap features in the device struct.
This is necessary to solve a deadlock on the dasd_devmap_lock which is
acquired by dasd_get_features called from the dasd tasklet. The current
implementation of devmap doesn't allow to call any devmap function from
interrupt or softirq context.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new machine check handler still has a few bugs.
1) The system entry time has to be stored in the machine check handler,
2) the machine check return psw may not be stored at the usual place
because it might overwrite the return psw of the interrupted context,
3) the return address for the call to s390_handle_mcck in the i/o interrupt
handler is not correct,
4) the system call cleanup has to take the different save area of the
machine check handler into account,
5) the machine check handler may not call UPDATE_VTIME before
CREATE_STACK_FRAME, and
6) the io leave path needs a critical section cleanup to make sure that the
TIF_MCCK_PENDING bit is really checked before switching back to user space.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bugfix (usage of uninitialized pointer in zfcp_port_dequeue) and compile
fixes for the zfcp device driver.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a severe problem with 2.6.13-rc7.
Due to recent SCSI changes it is not possible to add any LUNs to the zfcp
device driver anymore. With registration of remote ports this is fixed.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Acked-by: James Bottomley <jejb@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In qdio_get_micros() volatile in return type is plain noise (even with old
gccisms it would make no sense - noreturn function returning __u64 is a
bit odd ;-)
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
remove the bogus games with explicit ifdefs on __CHECKER__
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Martin Schwidesky <schwidefsky@de.ibm.com>
Convert qeth to the new klist interface and make it compiling again.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational. (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
vmcp_write uses GPF_DMA for the memory allocation of the response buffer, so
it can use the low level function __cpcmd directly, no need to call the
wrapper.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The FBA discipline does not use retries for failed requests. A request fails
after the first unsuccessful start attempt. There are some rare conditions
(e.g. CIO path recovery) in which the start of an i/o on a fba device can
fail. A tiny amount of retries is therefore reasonable.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When processing resource accessibility events, continue searching for further
affected subchannels if a link address is provided in the event information.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix debug data in case of an interface-control or channel-control check: don't
log the not yet accumulated interrupt-response-block, but the one we just
received.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Attached patch removes #ifdef CONFIG_WATCHDOG_NOWAYOUT mess duplicated in
almost every watchdog driver and replaces it with common define in
linux/watchdog.h.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tr_type_trans(), hippi_type_trans() left as-is.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the memory allocation method for the s390 debug feature.
Trace buffers had been allocated using the get_free_pages() function before.
Therefore it was not possible to get big memory areas in a running system due
to memory fragmentation. Now the trace buffers are subdivided into several
subbuffers with pagesize. Therefore it is now possible to allocate more
memory for the trace buffers and more trace records can be written.
In addition to that, dynamic specification of the size of the trace buffers is
implemented. It is now possible to change the size of a trace buffer using a
new debugfs file instance. When writing a number into this file, the trace
buffer size is changed to 'number * pagesize'.
In the past all the traces could be obtained from userspace by accessing files
in the "proc" filesystem. Now with debugfs we have a new filesystem which
should be used for debugging purposes. This patch moves the debug feature
from procfs to debugfs.
Since the interface of debug_register() changed, all device drivers, which use
the debug feature had to be adjusted.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add interface to issue VM control program commands.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improved machine check handling. Kernel is now able to receive machine checks
while in kernel mode (system call, interrupt and program check handling).
Also register validation is now performed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix compile breakage in the dcss block driver introduced by the attribute
changes.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the dasd driver to use the new klist interface.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the common I/O layer to use the klist interfaces.
This patch has been adapted from the previous version to the changed interface
semantics. Also, gcc 4.0 compile warnings have been removed.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the block device related part. The block device operation
direct_access now has a struct block_device as first parameter.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix max channel check in cio_ignore display function.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Heiko Carstens <heiko.carstens@de.ibm.com>
Fixes module parameter parsing for "device" parameter. The original
module parameter was changed while parsing it. This corrupted the
output in sysfs (/sys/module/zfcp/parameters/device).
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes a race between zfcp_fsf_req_dismiss_all and
zfcp_qdio_reqid_check. During adapter shutdown it occurred that a
request was cleaned up twice. First during its normal
completion. Second when dismiss_all was called. The fix is to
serialize access to fsf request list between zfcp_fsf_req_dismiss_all
and zfcp_qdio_reqid_check and delete a fsf request from the list if
its completion is triggered. (Additionally a rwlock was replaced by a
spinlock and fsf_req_cleanup was eliminated.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Fixes a bug in zfcp_send_els_handler. If D_ID assignments for ports
are changing between initiation of one ELS request and its completion
the wrong port might be accessed in the completion for that ELS
request. Thus a pointer to the port has to be passed for ELS requests
to identify the port structure if required.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Correct a bug in zfcp_fsf_send_fcp_command_handler. An fsf request
was not marked as failed if an unknown status qualifier was returned.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Reopen a remote port only if the link-test fails. This avoids that a
port is unnecessarily reopened.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Extend the time for adapter initialization: In case of protocol
status HOST_CONNECTION_INITIALIZING for the exchange config data
command do a first retry in 1 second, then double the sleep time for
each following retry until recovery exceeds 2 minutes. The old
behaviour of allowing 6 retries with .5 seconds delay between retries
was insufficient and qdio queues were shut down too erarly.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes the handling of failed requests for GID_PN nameserver command:
Set ZFCP_STATUS_PORT_INVALID_WWPN only if indicated by response
payload for GID_PN nameserver command and not if fsf request fails.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removes the rarely used "flags_dump" mechanism of zfcp.
Equivalent debug information will be provided with a reworking of
zfcp's s390dbf-facilities which is in preparation.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
dasd driver changes:
- The feature check in dasd_generic_online returns an error if
the devmap entry for the device is not yet available. Check
for the feature after the device has been created.
- Do symmetric registration/deregistration of cdev->handler.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[patch 10/10] s390: qeth bug fixes.
From: Frank Pavlic <pavlic@de.ibm.com>
qeth network driver related changes:
- due to OSA hardware changes in TCP Segmentation Offload
support we are able now to pack TSO packets too.
This fits perfectly in design of qeth buffer handling and
sending data respectively.
- remove skb_realloc_headroom from the sending path since
hard_header_len value provides enough headroom now.
- device recovery behaviour improvement
- bug fixed in Enhanced Device Driver Packing functionality
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
[patch 8/10] s390: fakell for high speed token ring.
From: Michael Holzheu <holzheu@de.ibm.com>
Implement fake-link-layer for high speed token ring. Without it
token ring packages get leading ethernet headers, which confuses
dhcp.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
[patch 7/10] s390: qeth bug fixes.
From: Frank Pavlic <pavlic@de.ibm.com>
qeth network driver changes:
- Removed redundant code, use the same qeth_fill_buffer_frag
for TSO path either
- Using skb->frags solely is not correct since skb->data still
points to the beginning of the whole data, even when it is
a small portion we have to fill the qdio buffer with it.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
[patch 6/10] s390: enable iucv_send2way_xxx functions.
From: Ursula Braun-Krahl <braunu@de.ibm.com>
The SSL-Server of z/VM wants to use the iucv_send2way
and iucv_send2way_array function. Enable them again.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
[patch 4/10] s390: schedule_timeout cleanup in ctctty.
From: Domen Puncer <domen@coderock.org>
Use msleep_interruptible() instead of schedule_timeout()
to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[patch 3/10] s390: set online race in the lcs driver.
From: Michael Holzheu <holzheu@de.ibm.com>
There is a race between lcs_stopcard() and lcs_open_device() which
can lead to the error 'lcs: Error in starting channel, rc=-16'.
lcs_open_device() is invoked when 'ifconfig up' is called due to a
hotplug event, which is caused by register_netdev(). In parallel
lcs_stopcard() is executed. Both functions are sending lcs commands.
The second invocation fails with -EBUSY (-16) as return value.
Move invocation of register_netdev() after invocation of lcs_stopcard
to avoid the race.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
[patch 2/10] s390: multicast address registration in lcs.
From: Michael Holzheu <holzheu@de.ibm.com>
When setting lcs devices online you can run into an endless loop,
because the code that registers the multicast addresses uses
list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
[patch 1/10] s390: claw driver wiring.
From: Andy Richter <richtera@us.ibm.com>
claw network driver changes:
- Add an entry to the drivers/s390/net Makefile to build the claw driver.
- Add claw channel type to cu3088.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ioctl32_conversion routines will be deprecated: Remove them from the
crypto driver.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ioctl32_conversion routines will be deprecated: Remove them from dasd_cmb
and handle the three cmb ioctls like all other dasd ioctls.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The first blocks on a cdl formatted dasd device are smaller than the blocksize
of the device. Read requests are padded with a 'e5' pattern. Write requests
should not pad the (user) buffer with 'e5' because a write request is not
allowed to modify the buffer.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The DASD device driver never reorders the I/O requests and relies on the
hardware to write all data to nonvolatile storage before signaling a
successful write. Hence, the only thing we have to do to support write
barriers is to set the queue ordered flag.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The independent read-only flags in devmap, dasd_device and gendisk are not
kept in sync. Use one bit per feature in the dasd driver and keep that bit in
sync with the gendisk bit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An arbitrary guest must not be allowed to trigger cmm actions. Only one
specific guest namely the one that serves as the resource monitor may send cmm
messages. Add a parameter that allows to specify the guest that may send
messages. z/VMs resource manager has the name 'VMRMSVM' which is the default.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide an easy way to define a non-zero storage key at compile time. This is
useful for debugging purposes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Andreas Herrmann <aherrman@de.ibm.com>
This patch mainly introduces support for point-2-point
topology.
From: Heiko Carstens <heiko.carstens@de.ibm.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
From: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
