If vertical cpu polarization is active then the hypervisor will
dispatch certain cpus for a longer time than other cpus for maximum
performance. For example if a guest would have three virtual cpus,
each of them with a share of 33 percent, then in case of vertical
cpu polarization all of the processing time would be combined to a
single cpu which would run all the time, while the other two cpus
would get nearly no cpu time.
There are three different types of vertical cpus: high, medium and
low. Low cpus hardly get any real cpu time, while high cpus get a
full real cpu. Medium cpus get something in between.
In order to switch between the two possible modes (default is
horizontal) a 0 for horizontal polarization or a 1 for vertical
polarization must be written to the dispatching sysfs attribute:
/sys/devices/system/cpu/dispatching
The polarization of each single cpu can be figured out by the
polarization sysfs attribute of each cpu:
/sys/devices/system/cpu/cpuX/polarization
horizontal, vertical:high, vertical:medium, vertical:low or unknown.
When switching polarization the polarization attribute may contain
the value unknown until the configuration change is done and the
kernel has figured out the new polarization of each cpu.
Note that running a system with different types of vertical cpus may
result in significant performance regressions. If possible only one
type of vertical cpus should be used. All other cpus should be
offlined.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Add s390 backend so we can give the scheduler some hints about the
cpu topology.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This patch adds the s390 variant for smp_call_function_mask(). The
implementation is pretty straight forward using the wrapper
__smp_call_function_map() which already takes a cpumask_t argument.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It caused only a lot of confusion. From now on cpu hotplug of up to
NR_CPUS will work by default. If somebody wants to limit that then
the possible_cpus parameter can be used.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
smp_call_function_single now has the same semantics as s390's
smp_call_function_on. Therefore convert to the *single variant
and get rid of some architecture specific code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the advent of kdump, the assumption that the boot CPU when booting an UP
kernel is always the CPU with a particular hardware ID (often 0) (usually
referred to as BSP on some architectures) is not valid anymore. The reason
being that the dump capture kernel boots on the crashed CPU (the CPU that
invoked crash_kexec), which may be or may not be that particular CPU.
Move definition of hard_smp_processor_id for the UP case to
architecture-specific code ("asm/smp.h") where it belongs, so that each
architecture can provide its own implementation.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s390 machines provide hardware support for creating Linux dumps on SCSI
disks. For creating a dump a special purpose dump Linux is used. The first
32 MB of memory are saved by the hardware before the dump Linux is
booted. Via an SCLP interface, the saved memory can be accessed from
Linux. This patch exports memory and registers of the crashed Linux to
userspace via a debugfs file. For more information refer to
Documentation/s390/zfcpdump.txt, which is included in this patch.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This provides a noexec protection on s390 hardware. Our hardware does
not have any bits left in the pte for a hw noexec bit, so this is a
different approach using shadow page tables and a special addressing
mode that allows separate address spaces for code and data.
As a special feature of our "secondary-space" addressing mode, separate
page tables can be specified for the translation of data addresses
(storage operands) and instruction addresses. The shadow page table is
used for the instruction addresses and the standard page table for the
data addresses.
The shadow page table is linked to the standard page table by a pointer
in page->lru.next of the struct page corresponding to the page that
contains the standard page table (since page->private is not really
private with the pte_lock and the page table pages are not in the LRU
list).
Depending on the software bits of a pte, it is either inserted into
both page tables or just into the standard (data) page table. Pages of
a vma that does not have the VM_EXEC bit set get mapped only in the
data address space. Any try to execute code on such a page will cause a
page translation exception. The standard reaction to this is a SIGSEGV
with two exceptions: the two system call opcodes 0x0a77 (sys_sigreturn)
and 0x0aad (sys_rt_sigreturn) are allowed. They are stored by the
kernel to the signal stack frame. Unfortunately, the signal return
mechanism cannot be modified to use an SA_RESTORER because the
exception unwinding code depends on the system call opcode stored
behind the signal stack frame.
This feature requires that user space is executed in secondary-space
mode and the kernel in home-space mode, which means that the addressing
modes need to be switched and that the noexec protection only works
for user space.
After switching the addressing modes, we cannot use the mvcp/mvcs
instructions anymore to copy between kernel and user space. A new
mvcos instruction has been added to the z9 EC/BC hardware which allows
to copy between arbitrary address spaces, but on older hardware the
page tables need to be walked manually.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Major cleanup of all s390 inline assemblies. They now have a common
coding style. Quite a few have been shortened, mainly by using register
asm variables. Use of the EX_TABLE macro helps as well. The atomic ops,
bit ops and locking inlines new use the Q-constraint if a newer gcc
is used. That results in slightly better code.
Thanks to Christian Borntraeger for proof reading the changes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use do { } while (0) constructs instead of empty defines to avoid
subtle compile bugs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce additional_cpus command line option. By default no additional cpu
can be attached to the system anymore. Only the cpus present at IPL time can
be switched on/off. If it is desired that additional cpus can be attached to
the system the maximum number of additional cpus needs to be specified with
this option.
This change is necessary in order to limit the waste of per_cpu data
structures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add missing smp_cpu_not_running define to avoid build warnings in the non smp
case.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements a number of smp_processor_id() cleanup ideas that
Arjan van de Ven and I came up with.
The previous __smp_processor_id/_smp_processor_id/smp_processor_id API
spaghetti was hard to follow both on the implementational and on the
usage side.
Some of the complexity arose from picking wrong names, some of the
complexity comes from the fact that not all architectures defined
__smp_processor_id.
In the new code, there are two externally visible symbols:
- smp_processor_id(): debug variant.
- raw_smp_processor_id(): nondebug variant. Replaces all existing
uses of _smp_processor_id() and __smp_processor_id(). Defined
by every SMP architecture in include/asm-*/smp.h.
There is one new internal symbol, dependent on DEBUG_PREEMPT:
- debug_smp_processor_id(): internal debug variant, mapped to
smp_processor_id().
Also, i moved debug_smp_processor_id() from lib/kernel_lock.c into a new
lib/smp_processor_id.c file. All related comments got updated and/or
clarified.
I have build/boot tested the following 8 .config combinations on x86:
{SMP,UP} x {PREEMPT,!PREEMPT} x {DEBUG_PREEMPT,!DEBUG_PREEMPT}
I have also build/boot tested x64 on UP/PREEMPT/DEBUG_PREEMPT. (Other
architectures are untested, but should work just fine.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!