* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix CPU hotplug when using the SLB shadow buffer
[POWERPC] efika: add phy-handle property for fec_mpc52xx
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
pnpacpi: print resource shortage message only once
PM: ACPI and APM must not be enabled at the same time
ACPI: apply quirk_ich6_lpc_acpi to more ICH8 and ICH9
ACPICA: fix acpi_serialize hang regression
ACPI : Not register gsi for PCI IDE controller in legacy mode
ACPI: Reintroduce run time configurable max_cstate for !CPU_IDLE case
ACPI: Make sysfs interface in ACPI power optional.
ACPI: EC: Enable boot EC before bus_scan
increase PNP_MAX_PORT to 40 from 24
ACPI and APM used "pm_active" to guarantee that
they would not be simultaneously active.
But pm_active was recently moved under CONFIG_PM_LEGACY,
so that without CONFIG_PM_LEGACY, pm_active became a NOP --
allowing ACPI and APM to both be simultaneously enabled.
This caused unpredictable results, including boot hangs.
Further, the code under CONFIG_PM_LEGACY is scheduled
for removal.
So replace pm_active with pm_flags.
pm_flags depends only on CONFIG_PM,
which is present for both CONFIG_APM and CONFIG_ACPI.
http://bugzilla.kernel.org/show_bug.cgi?id=9194
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
I noticed that the commit f197465384
(MIPS Tech: Get rid of volatile in core code) broke the software
reset functionality for MIPS Malta boards in big-endian mode.
According to the MIPS Malta board user's manual, writing the magic
32-bit GORESET value into the SOFTRES register initiates board soft
reset. My experimentation has shown that the endianness of the GORESET
integer should thereby be the same as the endianness, which has been
set for the CPU itself. The writew() function used to write the magic
value in the code introduced by the commit mentioned above, however,
swaps bytes for big-endian kernels and transfers 16 bits instead of 32.
The patch below replaces the writew() function by the __raw_writel()
routine, which leaves the byte order intact and transfers the whole
MIPS machine word. Trivial code cleanup (replacing spaces by a tab
and cutting oversized lines to make checkpatch.pl happy) is also
included.
The patch was tested using a Malta evaluation board running in both
BE and LE modes. For both modes, software reset was fully functional
after the change.
P.S. I suspect that the same commit broke the "standby" functionality
for MIPS Atlas boards. However, I did not touch the Atlas code as I
don't have such board at my disposal and also because the linux-mips.org
Web site claims that Atlas support is scheduled for removal.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts PNX8XXX system timer to clocksource restoring PNX8550
support back to live.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Before we register the SLB shadow buffer, we need to invalidate the
entries in the buffer, otherwise we can end up stale entries from when
we previously offlined the CPU.
This does this invalidate as well as unregistering the buffer with
PHYP before we offline the cpu. Tested and fixes crashes seen on
970MP (thanks to tonyb) and POWER5.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new network driver fec_mpc52xx will not work on efika because the
firmware does not provide all required properties.
http://www.powerdeveloper.org/asset/by-id/46 has a Forth script to
create more properties. But only the phy stuff is required to get a
working network.
This should go into the kernel because its appearently
impossible to boot the script via tftp and then load the real boot
binary (yaboot or zimage).
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With CPU_HOTPLUG=n:
WARNING: vmlinux.o(.text+0x104f8): Section mismatch: reference to .init.text:fork_idle (between
'do_fork_idle' and 'lapic_timer_broadcast')
do_fork_idle() needs to be __cpuinit. It can be static as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix CONFIG_BOOT_RAW.
[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug
[MIPS] Fix IP32 breakage
[MIPS] Alchemy: Fix use of __init code bug exposed by modpost warning
[MIPS] Move inclusing of kernel/time/Kconfig menu to appropriate place
This seems as reasonable assumption and gets some SNI machines to work
which currently must rely on the cp0 counter as clocksource.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- suppress master aborts during config read
- set io_map_base
- only fixup end of iomem resource to avoid failing request_resource
in serial driver
- killed useless setting of crime_int bit, which caused wrong interrupts
- use physcial address for serial port platform device and let 8250
driver do the ioremap
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: vmlinux.o(.text+0x1ca608): Section mismatch: reference to
.init.text: add_wired_entry (between 'config_access' and 'config_read')
by refactoring the code calling add_wired_entry() from config_access() to
a separate function which is called from aau1x_pci_setup(). While at it:
- make some unnecassarily global variables 'static';
- fix the letter case, whitespace, etc. in the comments...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_NO_HZ, CONFIG_HIGH_RES_TIMERS should be selected in "Kernel
type" menu, not in "CPU selection" menu.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Add missing i2c_board_info struct for at91rm9200
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Montecito and Montvale behaves slightly differently than previous
Itanium processors, resulting in the MCA due to a failed PIO read
to sometimes surfacing outside the nofault code. This code is
based on discussions with Intel CPU architects and verified at
customer sites.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Suspend/resume on the pxa25x was fairly obviously broken in revision
711be5ccfe.
This patch fixes the damage by adding back the missing code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit aed3a8c9bb introduced a
definition of notify_spus_active in .../cell/spu_syscalls.c, and
another definition under #ifndef MODULE in .../cell/spufs/sched.c.
The latter is not necessary and causes the build to fail when
CONFIG_SPU_FS=y, so this removes it. It also removes the export
of do_notify_spus_active, which is unnecessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
After 17d57a9206 ("x86: fix x86-32 early
fixmap initialization.") removing lg.ko caused a printk from vunmap:
mm/memory.c:115: bad pgd 004b3027.
On the second use after module load, the kernel crashes.
This fixes the immediate problem (accessed and dirty bits not set as
expected in pmd_none_or_clear_bad). I can't see why this would cause
a crash, but I haven't been able to reproduce it once this is applied.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in the printing of the os-area magic numbers which assumed
that magic numbers were zero terminated strings. The magic numbers
are represented in memory as integers. If the os-area sections are
not initialized correctly they could contained random data that would
be printed to the display. Also unify the handling of header and db
magic numbers and make both of type array of u8.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes an OProfile dependency on the spufs module. This
dependency was causing a problem for multiplatform systems that are
built with support for Oprofile on Cell but try to load the oprofile
module on a non-Cell system.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit fbdcf18df7.
As pointed out by Yanmin Zhang, the problem was already fixed
differently (and correctly), and rather than fix anything, it actually
causes us to create a sub-optimal sched-domains hierarchy (not setting
up the domain belonging to the core) when CONFIG_X86_HT=y.
Requested-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a cpu cache info entry for the Intel Tolapai cpu.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew "Eagle Eye" Morton noticed that we use raw_local_save_flags()
instead of raw_local_irq_save(flags) in die(). This allows the
preemption of oopsing contexts - which is highly undesirable. It also
causes CONFIG_DEBUG_PREEMPT to complain, as reported by Miles Lane.
this bug was introduced via:
commit 39743c9ef7
Author: Andi Kleen <ak@suse.de>
Date: Fri Oct 19 20:35:03 2007 +0200
x86: use raw locks during oopses
- spin_lock_irqsave(&die.lock, flags);
+ __raw_spin_lock(&die.lock);
+ raw_local_save_flags(flags);
that is not a correct open-coding of spin_lock_irqsave(): both the
ordering is wrong (irqs should be disabled _first_), and the wrong
flags-saving API was used.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when called by setup_arch) after smp_store_cpu_info() had set it to the
correct value.
The error shows up in 'cat /proc/cpuinfo' will all cpus = 0.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Suresh B Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Adjust CMCI mask on CPU hotplug
[IA64] make flush_tlb_kernel_range() an inline function
[IA64] Guard elfcorehdr_addr with #if CONFIG_PROC_FS
[IA64] Fix Altix BTE error return status
[IA64] Remove assembler warnings on head.S
[IA64] Remove compiler warinings about uninitialized variable in irq_ia64.c
[IA64] set_thread_area fails in IA32 chroot
[IA64] print kernel release in OOPS to make kerneloops.org happy
[IA64] Two trivial spelling fixes
[IA64] Avoid unnecessary TLB flushes when allocating memory
[IA64] ia32 nopage
[IA64] signal: remove redundant code in setup_sigcontext()
IA64: Slim down __clear_bit_unlock
Currently CMCI mask of hot-added CPU is always disabled after CPU hotplug.
We should adjust this mask depending on CMC polling state.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an unused variable warning in mm/vmalloc.c.
Tony: also fix resulting fallout in uncached.c with a
typo in args to flush_tlb_kernel_range().
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Access to elfcorehdr_addr needs to be guarded by #if CONFIG_PROC_FS
as well as the existing #if guards.
Fixes the following build problem:
arch/ia64/hp/common/built-in.o: In function
`sba_init':arch/ia64/hp/common/sba_iommu.c:2043: undefined reference to `elfcorehdr_addr'
:arch/ia64/hp/common/sba_iommu.c:2043: undefined reference to `elfcorehdr_addr'
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The Altix shub2 BTE error detail bits are in a different location
than on shub1. The current code does not take this into account
resulting in all shub2 BTE failures mapping to "unknown".
This patch reads the error detail bits from the proper location,
so the correct BTE failure reason is returned for both shub1
and shub2.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following assembler warning messages.
AS arch/ia64/kernel/head.o
arch/ia64/kernel/head.S: Assembler messages:
arch/ia64/kernel/head.S:1179: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1179: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
arch/ia64/kernel/head.S:1180: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1180: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
:
arch/ia64/kernel/head.S:1213: Warning: Use of 'ldf.fill.nta' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1213: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following compiler warning messages.
CC arch/ia64/kernel/irq_ia64.o
arch/ia64/kernel/irq_ia64.c: In function 'create_irq':
arch/ia64/kernel/irq_ia64.c:343: warning: 'domain.bits[0u]' may be used uninitialized in this function
arch/ia64/kernel/irq_ia64.c: In function 'assign_irq_vector':
arch/ia64/kernel/irq_ia64.c:203: warning: 'domain.bits[0u]' may be used uninitialized in this function
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I tried to upgrade an IA32 chroot on my IA64 to a new glibc with TLS.
It kept dying because set_thread_area was returning -ESRCH
(bugs.debian.org/451939).
I instrumented arch/ia64/ia32/sys_ia32.c:get_free_idx() and ended up
seeing output like
[pid] idx desc->a desc->b
-----------------------------
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> 0 0
[2710] 2 -> 0 0
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> c6b0ffff 40dff31b
[2710] 2 -> 0 0
[2711] 0 -> c6b0ffff 40dff31b
[2711] 1 -> c6b0ffff 40dff31b
[2711] 2 -> 48c0ffff 40dff317
which suggested to me that TLS pointers were surviving exec() calls,
leading to GDT pointers filling up and the eventual failure of
get_free_idx().
I think the solution is flushing the tls array on exec.
Signed-Off-By: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ia64 oops message doesn't include the kernel version, which
makes it hard to automatically categorize oops messages scraped
from mailing lists and bug databases.
Signed-off-by: Tony Luck <tony.luck@intel.com>
