Correct QAM symbol_rate_min for lgdt3302 and lgdt3303
Thanks to: Mac Michaels and Steve Malenfant
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/media/dvb/dvb-usb/dvb-usb-urb.c: In function `dvb_usb_allocate_stream_buffers':
drivers/media/dvb/dvb-usb/dvb-usb-urb.c:199: warning: int format, different type arg (arg 4)
Don't assume that dma_addr_t is 32-bit.
(dvb has quite a few such warnings. Please compile it with a 64-bit compiler,
fix them up - some are oopsable).
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adding support for the Artec T1 USB2.0 box (real USB2.0)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove status check from nxt200x_readreg_multibyte, it really shouldn't be
necessary.
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug in the software demux which causes large MPEG sections to be lost
when they follow very small sections.
The problem happens when two sections begin in the same transport packet. The
dvb_demux code resets its buffer only before the first of these sections.
This means that when the second (or subsequent) section begins, there is up to
182 bytes of buffer space already used. If the following section is close to
the maximum size, it currently won't fit in the (4096-byte) buffer and is
thrown away.
The fix is simply to enlarge the buffer by the size of one transport packet
and correct one usage of the SECFEED_SIZE definition where what is really
meant is the maximum size of a section.
Signed-off-by: Mark Adams <mark147m@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add support for AVerTVHD MCE a180.
- Instead of determining how to write to the tuner based on which NIM
is being used, make this determination based on whether the chip is a
NXT2002 or NXT2004.
- If NXT2004, write directly to tuner. If NXT2002, write through NXT chip.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed unnecessary null check before kfree() ...inspired by the big patch
from Jesper Juhl.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check that a callback (set_ts_params) is set before calling it.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* nxt200x.c, nxt200x.h
- New frontend module that supports both NXT2002 and NXT2004.
So far, only tested on NXT2004. After testing on NXT2002, we should
deprecate the nxt2002 module, and implement this one instead on the
applicable cards.
* get_dvb_firmware:
- Added support for the NXT2004 firmware. This firmware works with both
the ATI HDTV Wonder and the AVerTVHD MCE a180.
This was originally written by Jean-Francois Thibert
* dvb-pll.c
- Fixed minimum frequency for tuv1236d. It seems that the data sheets
are wrong.
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
stv0299_set_frontend(): reduced number of i2c transfers, set register 0x12
from inittab
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nebula nxt6000 requires fe reset.
Signed-off-by: Stuart Auchterlonie <stuarta@squashedfrog.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added support for the following:
Philips TUV1236D - ATI HDTV Wonder
ALPS TDHU2 - AverTVHD MCE A180
Samsung TBMV30111IN - Air2PC ATSC - 2nd generation
These will be used in a new NXT200X driver that incorporates the NXT2002
driver and adds support for a couple NXT2004 based cards.
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dst_write_tuna needs to be protected against simultaeneous writes, just like
dst_command
Signed-off-by: Henrik Sjoberg <henke@epact.se>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to protect the read/write commands with a mutex.
Bug reported by Henrik Sjoberg <henke@epact.se>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added support for Air2PC/AirStar 2 ATSC 3rd generation (HD5000)
Signed-off-by: Taylor Jacob <rtjacob@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove DEBUG_LOCKLOSS stuff - as the problem has been found and resolved
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support to FE_DISHNETWORK_SEND_LEGACY_CMD code to support other frontends
besides stv0299. The generic code is a fallback in the case that it doesn't
work for some specific frontends (again stv0299 being a good example).
Signed-off-by: NooneImportant <nxhxzi702@sneakemail.com>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix integer overflow bug in read_signal_strength() reported by Anthony
Leclerc.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes a possible buffer overflow due to reading more than 8 bytes into an 8
byte long array
Thanks to Perceval Anichini <perceval.anichini@streamvision.fr> for pointing
out the bug.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
removes the redundant checksum calculation, which was also exported from the
dst.c module
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
fix DST DVB-S get_frequency
- fixes a bug that caused the returned frequency to wrong
Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
fixes broken support for vp-3040 TS204
Thanks-to: Lee Hammerton <savoury.snax@bulldoghome.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sparse warnings
- remove address space related warnings
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ASN.1 length field Fix
Signed-off-by: Raymond Mantchala <raymond.mantchala@streamvision.ft>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix charge pump setting in microtune_mt7202dtf_pll_set(). Thanks to Jyrki
Niskala for reporting.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The duplicate key definitions cause misinterpretations with other keys, e.g.
the "TELETEXT" key clashes with "CHANNEL_UP" and thus can not be used with
LIRC. This patch removes these duplicates.
Signed-off-by: Thorsten Maerz <torte@netztorte.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed unavoidable error message and related code.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- leave I2C bridge open at pll_sleep to support Philips EUROPA based cards.
- give an error message if the communication with the pll fails.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added ATSC support for DViCO FusionHDTV5 Lite.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove my badly thought out patch. This does need done, but in a proper way.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the Technotrend Budget Card S1500 with a BSBE1
frontend and the LNBP21.
Signed-off-by: Martin Zwickel <martin.zwickel@technotrend.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/media/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/media/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: Johannes Stezenbach <js@linuxtv.org>
Cc: Michael Krufky <mkrufky@m1k.net>
Cc: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Acked-by : Manu Abraham <manu@linuxtv.org>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Acked-by: Wilson Michaels <wilsonmichaels@earthlink.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the remaining "Using plain integer as NULL pointer" sparse
warnings to use NULL. (Not duplicating patches that are already in -mm,
-bird, or -kj.)
Convert isdn driver struct initializer to use C99 syntax.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ralph Metzler wrote:
> AFAIR, there is a bug in tda10021.c in tda10021_readreg() which
> references state->frontend.dvb->num
> This is fatal if the frontend is not at the probed address and thus
> not yet registered (no dvb entry set yet -> NULL pointer ...).
The attached patch should get rid of the oops.
Signed-off-by: Jon Burgess <jburgess@uklinux.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of the time_after_eq() macro, defined at linux/jiffies.h, which deal
with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add PCI-ids of Siemens-DVB-C card with Technotrend manufacturer id.
Signed-off-by: Karl Herz <karl.herz@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improved remote control support for av7110-based cards:
o extended rc5 protocol, firmware >= 0x2620 required
o key-up timer slightly adjusted
o completely moved remote control code to av7110_ir.c
o support for multiple ir receivers
o for now, all av7110 cards share the same ir configuration and event device
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable frontend on KNC plus cards.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes for CI interface.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for TT DVB-C CI card.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for analog video inputs (CVBS and Y/C) of the
analog module for the Siemens DVB-C card.
Signed-off-by: thomas schorpp <t.schorpp@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IR RC fixes:
- EVIOCSKEYCODE is not supported by this driver, fix potential crash
when it is used by not setting rc_input_dev->keycodesize
- fix key repeat handling (hopefully)
- reduce default poll internal to 50msec (necessary for key repeat handling)
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix BUG in DVB-C frequency setting. Thanks to Peng Cao <caopeng75@gmail.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Identify board properly: Add functions to retrieve MAC Address, FW details,
Card type and Vendor Information.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Code Cleanup:
o Remove debug noise
o Remove debug module parameter
debug level is achieved using the verbosity level
o Updated to kernel coding style
(case labels should not be indented)
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Code Simplification: CA PMT object is not parsed in the driver anymore.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the Symbolrate setting card specific.
Signed-off-by: Manu Abraham <manu@kromtek.com>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug in Nebula DigiTV frontend detection for nxt6000.
Signed-off-by: Stuart Auchterlonie <stuarta@squashedfrog.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for Nebula DigiTV PCI cards with the MT352 frontend.
Signed-off-by: David Johnson <dj@david-web.co.uk>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Indentation fixes and remove unnecessary braces.
Signed-off-by: David Johnson <dj@david-web.co.uk>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Endianness fix for risc DMA start address setting. (reported by Stefan
Haubenthal/Peter Hettkamp)
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
comment out noisy dprintk in dst_get_signal() (why are errors only visible
with debug on? this needs to be cleaned up so we can disable debug by
default)
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes two things:
1) a firmware update made by the vendor, which has to be done in Windows
for now, changes the DVB-data-pipe from isochronous to bulk: it fixes the
data distortions (and thus the video-distortions) in DVB-T mode; there is
no backwards compatibility with the old firmware as it didn't work anyway
2) with the help of Steve Toth some reverse-engineered functionality is now
named correctly, thank you
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
white space cleanup
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the NXT6000-based digitv-box. Add .get_tune_settings callback
for the NXT6000 to have a min_tune_delay of 500ms.
Signed-off-by: Svante Olofsson <svante@agentum.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the init call to optionally return the new dvb_usb_device directly.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added names for clones of the DVB-T stick.
Whitespace cleanups.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add USB IDs of the Kworld Xpert DVB-T USB2.0 (clone of the ADStech box).
Thanks to Marcus Hagn for testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add driver for the TwinhanDTV StarBox and clones.
Thanks to Ralph Metzler for his initial work on this box and thanks to Twinhan
for their support.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fix has also been applied to lgdt330x. There is an optimization that
keeps track of the frequency tuned by the digital decoder. The digital driver
does not set the frequency if it has not changed since it was tuned. The
analog tuner driver knows nothing about the frequency saved by the digital
driver. When the frequency is set using the video4linux code with tvtime, the
hardware get changed but the digital driver's state does not get updated.
Switch back to the same digital channel and the driver finds no change in
frequency so the tuner is not reset to the digital frequency. The work around
is to remove the check and always set the tuner to the specified frequency.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
while investigating the QAM_128-issue with the stv0297-driver for the
Cablestar (which is not the same as the one in dvb-kernel CVS, yet), I fixed
it, not by increasing the timeout, but by disabling the corner-detection for
QAM_128 and higher.
This patch has been tested on dvb-kernel cvs, and has been reported to work by
multiple users. Some cards still need timeout increase on top of this patch.
This will be addressed later.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up timeout handling.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix DiSEqC switching (one bug fix suggested by Peter Hettkamp, and one
experimentally determined msleep(30) suggested by Adam Szalkowski).
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reset acgconf register after tuning to improve locking, as suggested by Marco
Schluessler. Minor cleanups in ves1820_init().
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix SNR reading
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the stv0299 to read the BER and UCBLOCKS.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Misc. fixes.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass a pointer to the i2c bus to the pll callbacks (stv0299 only).
It was not possible to tell which i2c bus should be used if an adapter has
multiple frontends on multiple i2c buses.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix two problems with the signal strength value in the mt352.c frontend:
1. the 4 most significant bits are zeroed - shift and mask wrong way round
2. need to align the 12 bits from the registers at the top of the 16 bit
returned value - otherwise the range is not 0 to 0xffff its 0xf000 to 0xffff
Signed-off-by: Barry Scott <barry.scott@onelan.co.uk>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Dominique Dumont to get the SCM Red Viaccess CAM working with the
budget-ci.
Signed-off-by: Dominique Dumont <domi.dumont@free.fr>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use INIT_LIST_HEAD for frontend_list.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed more unused variables and constants.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed some useless functions and variables.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't return immediately from dvb_dmx_swfilter_section_packet() if CC is not
ok. Otherwise a new feed drops all packets until the first packet with CC=0
arrives.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Glue code for DMX_GET_CAPS and DMX_SET_SOURCE ioctls.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove all #include <linux/version.h> and all references to LINUX_VERSION_CODE
and KERNEL_VERSION. Based on patch by Olaf Hering.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update email address of Peter Hettkamp.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of the patch is whitespace cleanup, but more importantly, this patch
checks to see whether a callback is set before calling it. On cx88 boards
(currently the only boards using lgdt330x in 2.6.13) every callback is set.
However, newer drivers currently in development leave a callback undefined,
and lgdt330x must not call it if it isn't defined.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patrick Keene wrote to the linux-dvb list, asking where in menuconfig he
can enable dvb-bt8xx for his AVerMedia DVB card. I pointed the following
out to him:
config DVB_BT8XX
tristate "Nebula/Pinnacle PCTV/Twinhan PCI cards"
It has been agreed upon that this description is extremely misleading.
This patch changes the one-liner description text of dvb-bt8xx to something
more meaningful, and adds AVerMedia to the detailed description.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In theory, there should be no more users of I2C_ALGO_* at this point.
However, it happens that several drivers were using I2C_ALGO_* for
adapter ids, so we need to correct these before we can get rid of all
the I2C_ALGO_* definitions.
Note that this also fixes a bug in media/video/tvaudio.c:
/* don't attach on saa7146 based cards,
because dedicated drivers are used */
if ((adap->id & I2C_ALGO_SAA7146))
return 0;
This test was plain broken, as it would succeed for many more adapters
than just the saa7146: any those id would share at least one bit with
the saa7146 id. We are really lucky that the few other adapters we want
this driver to work with did not fulfill that condition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more users of i2c_algorithm.id, so we can finally drop
this structure member.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The name member of the i2c_algorithm is never used, although all
drivers conscientiously fill it. We can drop it completely, this
structure doesn't need to have a name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes the following compile error:
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `frontend_init':
budget-av.c:(.text+0xb9448): undefined reference to `tda10046_attach'
budget-av.c:(.text+0xb9518): undefined reference to `tda10021_attach'
drivers/built-in.o: In function `philips_tu1216_request_firmware':
budget-av.c:(.text+0xb937b): undefined reference to `request_firmware'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Johannes Stezenbach <js@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed race between submitting streaming URBs in the driver and starting
the actual transfer in hardware (demodulator and USB controller) which
sometimes lead to garbled data transfers. URBs are now submitted first,
then the transfer is enabled. Dibusb devices and clones are now fully
functional again.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the tda9887 stuff from lgdt330x.c. It's experimental code
which wasn't supposed to leak out and we don't want it in 2.6.13.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Acked-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two trivial text changes in Kconfig and lgdt330x.c
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Structural changes within lgdt330x driver, framework now supports
both chips... tested OK on lgdt3302 and lgdt3303.
- Add LG/TUA6034 dvb_pll_desc for ATSC with LG TDVS-H062F & DViCO FusionHDTV5.
- Fixed LGDT330X signal strength: For now, always set it to 0.
- Corrected LGDT330X boundary condition error in read_snr: dB calculation.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename lgdt3302 to lgdt330x, to make way for the addition of lgdt3303
support in future revisions.
I am changing the name of this module now so that hopefully the name will
be changed before the release of 2.6.13 ... It wouldn't make sense to
release 2.6.13 with the name lgdt3302 in it, which will only be renamed to
lgdt330x in later versions.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
warning: `i2c_readbytes' defined but not used
This code will either be re-enabled or deleted in a future patch.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Select the RF input connector based upon the type of demodulation selected.
ANT RF connector is selected for 8-VSB and CABLE RF connector is selected
for QAM64/QAM256. This only affects the cards that use the Microtune 4042
tuner.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the dvb_pll_desc from the frontend and replace with a
pll_set-callback to isolate the tuner programming from the frontend.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is a small modification to the table that defines the way that the
LG-Z201 tuner is controlled for the DVICO Fusion DVB-T1 tuner card.
I believe that a mistake was made when the dvb tuner code was reorganised
(to use a generic table for the tuner information instead of inline code)
and as a result, the DVICO card doesn't tune properly.
The modification I have made to the table makes it behave like it did with
the old inline tuner code that worked. The patch is on top of the 2.6.12
kernel.
Signed-off-by: Gregory B Frost <frosts1@hotkey.net.au>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix QAM lock bug. Previously, it was necessary to first scan in VSB before
attempting to get a QAM lock.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The / in the driver name (budget dvb /w video in) is not a valid character for
device names - removed it, now it works!
Same for ttusb-budget.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
corrected some typos.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Initialize all non mutually exclusive variables
without regard to the mode selected.
- Do a software reset each time the parameters are
set, regardless of whether anything changes.
This may allow an application to recover from a
hung condition.
- Improved error reporting.
- Removed $Id:$
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Correct sync byte for MPEG-2 transport stream packets.
- Add lgdt3302 as dependency of cx88-dvb in Kconfig.
- Add dvb support in v4l for DViCO FusionHDTV3 Gold-T using lgdt3302 frontend.
This adds support for a different board from the previous (Gold-Q) patch.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support and rewrote some parts with the help of vendor information
(Thanks to Steve Chang from WideView, Inc.):
o added support for the WT-220U (Pensize DVB-T receiver)
o corrected byte order for unc,ber and the pid filter
o corrected number of pids that can be fetched at the same time.
o added some comments in Kconfig-file
o added USB IDs for the WT-220U
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix tuning failure for 200103A, 200103A failed to tune to low band due to
wrong tone setting on the 200103A.
Signed-off-by: Steffen Motzer <motzersn@tlink.de>
Signed-off-by: Manu Abraham <manu@kromtek.com>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name-field of the pci_driver and usb_driver structs to the name of
the module after compilation. It seems that this field is used in some places
where special characters are not allowed. Thanks to Alan Halverson for
finding this problem.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for LGDT3302 (ATSC VSB/QAM) used in DViCO FusionHDTV3 Gold.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Timeout handling fixed, especially for preemtible kernels and/or high system
load.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't use HZ for usb-transfer-timeouts.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o add some remote control codes
o not using HZ for control_msg-timeout
Signed-off-by: Andrew Hodgson <a.s.hodgson@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o fixed usage of the correct number of events in keymapping-array
o better place for return
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct two keys of the vp7045 remote control key mapping.
Signed-off-by: Michael Paxton <packo@tpg.com.au>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Steve Chang reported the real name behind 0x14aa: WideView,
changed USB IDs accordingly.
o fixed an assignment
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o corrected some typos
o added the Wikilink pointing to the USB device list
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix memcpy copying into the wrong destination. Thanks to Allan Third for
reporting.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add another USB ID pair for the VideoWalker USB DVB-T.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was no pid-filter-count set for some devices - led to an error. Thanks
to Gerolf Wendland.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some more work on the digitv-usb driver:
o MT352 initialization and PLL-programming
o I2c-transfer fixed.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add dvb_pll_desc for ALPS TDED4 used in Nebula USB boxes. Changed the
name-field of the FMD1216.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add module parameter to deactive remote control polling.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add preliminary support for the Medion Hybrid USB2.0 DVB-T/Analogue box.
Analogue part is not working yet (cx25842 --> ivtv?).
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o change dvb-pll desc to take the frequency as parameter for setbw-callback
into consideration
o added dvb-pll desc for Philips FMD1216ME (needed for cxusb)
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed support for the ADSTech Instant TV DVB-T USB (2.0 version). Thanks to
Gerolf Wendland for his support.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add #define for device with broken USB ids.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
av7110_fe_lock_fix() modified in a way that it can be retried after
-ERESTARTSYS
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix indentation and add some whitepsace between operators.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change error handling in av7110_stop_feed() to stop as many filters as
possible in case of errors.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o propagate more errors back to caller or log them, mainly in
av7110.c and av7110_av.c
o fix error message in StartHWFilter
o do not StopHWFilter for handle 0xffff
Signed-off-by: Wolfgang Rohdewald <wolfgang@rohdewald.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix for QAM128 in VHF band suggested by Timo Helkiö.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug in timeout handling.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o make sure ERESTARTSYS will be propagated
o ReleaseBitmap: starting with Firmware 261e, also release when
BMP_LOADING
o removes unused #define BMP_LOADINGS
o in many cases changed the return value from -1 to something more
meaningful like ETIMEDOUT, EINVAL
o changed syslog message timeout waiting for COMMAND such that it
indicates what command did not complete
o reduce # of arguments for LoadBitmap and BlitBitmap
o av7110_osd_cmd: remove the out: label
Signed-off-by: Wolfgang Rohdewald <wolfgang@rohdewald.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
