* 'for-next' of git://git.o-hand.com/linux-mfd:
mfd: fix da903x warning
mfd: fix MAINTAINERS entry
mfd: Use the value of the final spin when reading the AUXADC
mfd: Storage class should be before const qualifier
mfd: PASIC3: supply clock_rate to DS1WM via driver_data
mfd: remove DS1WM clock handling
mfd: remove unused PASIC3 bus_shift field
pxa/magician: remove deprecated .bus_shift from PASIC3 platform_data
mfd: convert PASIC3 to use MFD core
mfd: convert DS1WM to use MFD core
mfd: Support active high IRQs on WM835x
mfd: Use bulk read to fill WM8350 register cache
mfd: remove duplicated #include from pcf50633
* 'for-linus' of git://repo.or.cz/cris-mirror:
CRISv32: Remove extraneous space between -I and the path.
cris: convert obsolete hw_interrupt_type to struct irq_chip
BUG to BUG_ON changes
cpumask: use mm_cpumask() wrapper: cris
cpumask: Use accessors code.: cris
cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.: cris
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: sh7785lcr: Map whole PCI address space.
sh: Fix up DSP context save/restore.
sh: Fix up number of on-chip DMA channels on SH7091.
sh: update defconfigs.
sh: Kill off broken direct-mapped cache mode.
sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
sh: Add a command line option for disabling I/O trapping.
sh: Select ARCH_HIBERNATION_POSSIBLE.
sh: migor: Fix up CEU use flags.
input: migor_ts: add wakeup support
rtc: rtc-sh: use set_irq_wake()
input: sh_keysc: use enable/disable_irq_wake()
sh: intc: set_irq_wake() support
sh: intc: install enable, disable and shutdown callbacks
clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
sh: Fix up -Wformat-security whining.
sh: ap325rxa: Add ov772x support, again.
sh: Sanitize asm/mmu.h for assembly use.
sh: Tidy up sh7786 pinmux table.
...
* 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: add hardware handshake support to atmel_serial
avr32: add RTS/CTS/CLK pin selection for the USARTs
Add RTC support for Merisc boards
avr32: at32ap700x: setup DMA for AC97C in the machine code
avr32: at32ap700x: setup DMA for ABDAC in the machine code
Add Merisc board support
avr32: use gpio_is_valid() to check USBA vbus_pin I/O line
atmel-usba-udc: use gpio_is_valid() to check vbus_pin I/O line
avr32: fix timing LCD parameters for EVKLCD10X boards
avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
avr32: configure MCI detect and write protect pins for EVKLCD10x boards
avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
avr32: add pin mask for 18-bit color on the LCD controller
avr32: fix 15-bit LCDC pin mask to use MSB lines
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask: (36 commits)
cpumask: remove cpumask allocation from idle_balance, fix
numa, cpumask: move numa_node_id default implementation to topology.h, fix
cpumask: remove cpumask allocation from idle_balance
x86: cpumask: x86 mmio-mod.c use cpumask_var_t for downed_cpus
x86: cpumask: update 32-bit APM not to mug current->cpus_allowed
x86: microcode: cleanup
x86: cpumask: use work_on_cpu in arch/x86/kernel/microcode_core.c
cpumask: fix CONFIG_CPUMASK_OFFSTACK=y cpu hotunplug crash
numa, cpumask: move numa_node_id default implementation to topology.h
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
cpumask: remove x86 cpumask_t uses.
cpumask: use cpumask_var_t in uv_flush_tlb_others.
cpumask: remove cpumask_t assignment from vector_allocation_domain()
cpumask: make Xen use the new operators.
cpumask: clean up summit's send_IPI functions
cpumask: use new cpumask functions throughout x86
x86: unify cpu_callin_mask/cpu_callout_mask/cpu_initialized_mask/cpu_sibling_setup_mask
cpumask: convert struct cpuinfo_x86's llc_shared_map to cpumask_var_t
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
x86: unify 32 and 64-bit node_to_cpumask_map
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: use strstarts()
strstarts: helper function for !strncmp(str, prefix, strlen(prefix))
arm: allow usage of string functions in linux/string.h
module: don't use stop_machine on module load
module: create a request_module_nowait()
module: include other structures in module version check
module: remove the SHF_ALLOC flag on the __versions section.
module: clarify the force-loading taint message.
module: Export symbols needed for Ksplice
Ksplice: Add functions for walking kallsyms symbols
module: remove module_text_address()
module: __module_address
module: Make find_symbol return a struct kernel_symbol
kernel/module.c: fix an unused goto label
param: fix charp parameters set via sysfs
Fix trivial conflicts in kernel/extable.c manually.
The PASIC3 driver now calculates its register spacing from the resource
size.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
PCI still doesn't work on sh7785lcr 29bit 256M map mode.
On SH7785, PCI -> SHwy address translation is not base+offset but
somewhat like base|offset (See HW Manual (rej09b0261) Fig. 13.11).
So, you can't export CS2,3,4,5 by 256M at CS2 (results CS0,1,2,3
exported, I guess). There are two candidates.
a) 128M@CS2 + 128M@CS4
b) 512M@CS0
Attached patch is B. It maps 512M Byte at 0 independently of memory
size. It results CS0 to CS6 and perhaps some more being accessible
from PCI.
Tested on
7785lcr 29bit 128M map
7785lcr 29bit 256M map
(NOT tested on 32bit)
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.
This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This accidentally regressed when the multi-IRQ changes went in,
switching SH7091 from 4 to 6 channels. Add SH7091 back in to the
4-channel dependency list.
Reported-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
interrupt remapping must be enabled before enabling x2apic, but
interrupt remapping doesn't depend on x2apic, it can be used
separately. Enable interrupt remapping in init_dmars even x2apic
is not supported.
[dwmw2: Update Kconfig accordingly, fix build with INTR_REMAP && !X2APIC]
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
s390: remove arch specific smp_send_stop()
panic: clean up kernel/panic.c
panic, smp: provide smp_send_stop() wrapper on UP too
panic: decrease oops_in_progress only after having done the panic
generic-ipi: eliminate WARN_ON()s during oops/panic
generic-ipi: cleanups
generic-ipi: remove CSD_FLAG_WAIT
generic-ipi: remove kmalloc()
generic IPI: simplify barriers and locking
All logical processors with APIC ID values of 255 and greater will have their
APIC reported through Processor X2APIC structure (type-9 entry type) and all
logical processors with APIC ID less than 255 will have their APIC reported
through legacy Processor Local APIC (type-0 entry type) only. This is the
same case even for NMI structure reporting.
The Processor X2APIC Affinity structure provides the association between the
X2APIC ID of a logical processor and the proximity domain to which the logical
processor belongs.
For OSPM, Procssor IDs outside the 0-254 range are to be declared as Device()
objects in the ACPI namespace.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6: (21 commits)
xtensa: we don't need to include asm/io.h
xtensa: only build platform or variant if they contain a Makefile
xtensa: make startup code discardable
xtensa: ccount clocksource
xtensa: remove platform rtc hooks
xtensa: use generic sched_clock()
xtensa: platform: s6105
xtensa: let platform override KERNELOFFSET
xtensa: s6000 variant
xtensa: s6000 variant core definitions
xtensa: variant irq set callbacks
xtensa: variant-specific code
xtensa: nommu support
xtensa: add flat support
xtensa: enforce slab alignment to maximum register width
xtensa: cope with ram beginning at higher addresses
xtensa: don't make bootmem bitmap larger than required
xtensa: fix init_bootmem_node() argument order
xtensa: use correct stack pointer for stack traces
xtensa: beat Kconfig into shape
...
pci mmap code was doing memtype reserve for a while now. Recently we
added memtype tracking in remap_pfn_range, and pci code indirectly calls
remap_pfn_range. So, we don't need seperate tracking in pci code
anymore. Which means a patch that removes ~50 lines of code :-).
Also, recently we found out that the pci tracking is not working as we expect
it to work in some cases. Specifically, userlevel X mmap of pci, with some
recent version of X, is having a problem with vm_page_prot getting reset.
The pci tracking uses vm_page_prot to pass on the protection type from parent
to child during fork.
a) Parent does a pci mmap
b) We look at PAT and get either UC_MINUS or WC mapping for parent
c) Store that mapping type in vma vm_page_prot for future use
d) This thread does a fork
e) Fork results in mmap_ops ->open for the child process
f) We get the vm_page_prot from vma and reserve that type for the child process
But, between c) and e) above, the vma vm_page_prot is getting reset to zero.
This results in PAT reserve failing at the time of fork as in here.
http://marc.info/?l=linux-kernel&m=123858163103240&w=2
This cleanup makes the above problem go away as we do not depend on
vm_page_prot in our PAT code anymore.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables suspend/resume for interrupt remapping. During suspend,
interrupt remapping is disabled. When resume, interrupt remapping is enabled
again.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The __restore_processor_state() fn restores %gs on resume from S3. As
such, it cannot be protected by the stack-protector guard since %gs will
not be correct on function entry.
There are only a few other fns in this file and it should not negatively
impact kernel security that they will also have the stack-protector
guard removed (and so it's not worth moving them to another file).
Without this change, S3 resume on a kernel built with
CONFIG_CC_STACKPROTECTOR_ALL=y will fail.
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
LKML-Reference: <49D13385.5060900@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Fix address wrap on 32-bit kernel.
intel-iommu: Enable DMAR on 32-bit kernel.
intel-iommu: fix PCI device detach from virtual machine
intel-iommu: VT-d page table to support snooping control bit
iommu: Add domain_has_cap iommu_ops
intel-iommu: Snooping control support
Fixed trivial conflicts in arch/x86/Kconfig and drivers/pci/intel-iommu.c
Commit 7ca43e7564 ("mm: use debug_kmap_atomic")
introduced some debug_kmap_atomic() in wrong places.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (41 commits)
m68knommu: improve compile arch switch settings
m68knommu: fix 5407 ColdFire UART vector setup
m68knommu: fix 5307 ColdFire UART vector setup
m68knommu: fix 5249 ColdFire UART vector setup
m68knommu: fix 5249 ColdFire UART setup
m68knommu: fix end of uart table marker
m68knommu: switch to using generic_handle_irq()
m68k: merge the mmu and non-mmu versions of tlbflush.h
m68knommu: introduce basic clk infrastructure
m68k: merge the mmu and non-mmu versions of module.h
m68knommu: add missing interrupt line definition for UART 2
m68k: merge the mmu and non-mmu versions of mmu_context.h
m68k: merge the mmu and non-mmu versions of current.h
m68k: merge the mmu and non-mmu versions of div64.h
m68k: merge the mmu and non-mmu versions of bugs.h
m68k: merge the mmu and non-mmu versions of bug.h
m68k: use the mmu version of cache.h for m68knommu as well
m68k: use the mmu version of bootinfo.h for m68knommu as well
m68k: merge the mmu and non-mmu versions of fb.h
m68k: merge the mmu and non-mmu versions of segment.h
...
i386 allnoconfig:
arch/x86/mm/iomap_32.c: In function 'is_io_mapping_possible':
arch/x86/mm/iomap_32.c:27: warning: comparison is always false due to limited range of data type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] fix build-breaking 7a192ec commit
ARM: Add SMSC911X support to Overo platform (V2)
arm: update omap_ldp defconfig to use smsc911x
arm: update realview defconfigs to use smsc911x
arm: update pcm037 defconfig to use smsc911x
arm: convert omap ldp platform to use smsc911x
arm: convert realview platform to use smsc911x
arm: convert pcm037 platform to use smsc911x
[ARM] 5444/1: ARM: Realview: Fix event-device multiplicators in localtimer.c
[ARM] 5442/1: pxa/cm-x255: fix reverse RDY gpios in PCMCIA driver
[ARM] 5441/1: Use pr_err on error paths in at91 pm
[ARM] 5440/1: Fix VFP state corruption due to preemption during VFP exceptions
[ARM] 5439/1: Do not clear bit 10 of DFSR during abort handling on ARMv6
[ARM] 5437/1: Add documentation for "nohlt" kernel parameter
[ARM] 5436/1: ARM: OMAP: Fix compile for rx51
[ARM] arch_reset() now takes a second parameter
[ARM] Kirkwood: small L2 code cleanup
[ARM] Kirkwood: invalidate L2 cache before enabling it
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/linux-hdreg-h-cleanup:
remove <linux/ata.h> include from <linux/hdreg.h>
include/linux/hdreg.h: remove unused defines
isd200: use ATA_* defines instead of *_STAT and *_ERR ones
include/linux/hdreg.h: cover WIN_* and friends with #ifndef/#endif __KERNEL__
aoe: WIN_* -> ATA_CMD_*
isd200: WIN_* -> ATA_CMD_*
include/linux/hdreg.h: cover struct hd_driveid with #ifndef/#endif __KERNEL__
xsysace: make it 'struct hd_driveid'-free
ubd_kern: make it 'struct hd_driveid'-free
isd200: make it 'struct hd_driveid'-free
Impact: code size reduction (possibly critical)
The x86 boot and decompression code has no use of the branch profiling
constructs, so disable them. This would bloat the setup code by as
much as 14K, eating up a fairly large chunk of the 32K area we are
guaranteed to have.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: unification of pci-dma macros and pci_32.h removal
This patch unifies the definition of the pci_unmap_addr*, pci_unmap_len*
and DECLARE_PCI_UNMAP* macros. This makes sense because the pci_unmap
functions are no longer no-ops anymore when the kernel runs with
CONFIG_DMA_API_DEBUG. Without an iommu or DMA_API_DEBUG it is a no-op on 32 bit
because the dma mapping path returns a physical address and therefore the
dma-api implementation has no internal state which needs to be destroyed with
an unmap call.
This unification also simplifies the port of x86_64 iommu drivers to 32 bit x86
and let us get rid of pci_32.h.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
We only add the platform or variant directory to core-y if it
contains a Makefile. Consequently, we can remove the Makefiles
for the dc232b and fsf processor variants.
Signed-off-by: Chris Zankel <chris@zankel.net>
Move it from .text to .init.text to get rid of it after boot and
prevent illegal section references.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Switch to GENERIC_TIME by using the ccount register as a clock source.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
platform_get/set_rtc_time() is not implemented by any of the supported
xtensa platforms. Remove the facility completely.
The initial seconds for xtime come from read_persistent_clock() which
returns just 0 in the generic implementation. Platforms that sport a
persistent clock can implement this function.
This is needed to implement the ccount as a clock source.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
Current xtensa implementation of sched_clock() is the same as the
generic one. Just remove it, the weak symbol in kernel/sched_clock.c
will be used instead.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
Support for the S6105 IP Camera Reference Design Kit.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
The linker script should not assume a fix offset in memory for the
kernel, this is platform-specific, so let the platform set it.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Support for the Stretch S6000 Xtensa core variant.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Allow the core variant code to provide irq enable/disable callbacks.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
