This is a driver for the ADS7846 touchscreen sensor, derived from
the corgi_ts and omap_ts drivers. Key differences from those two:
- Uses the new SPI framework (minimalist version)
- <linux/spi/ads7846.h> abstracts board-specific touchscreen info
- Sysfs attributes for the temperature and voltage sensors
- Uses fewer ARM-specific IRQ primitives
The temperature and voltage sensors show up in sysfs like this:
$ pwd
/sys/devices/platform/omap-uwire/spi2.0
$ ls
bus@ input:event0@ power/ temp1 vbatt
driver@ modalias temp0 vaux
$ cat modalias
ads7846
$ cat temp0
991
$ cat temp1
1177
$
So far only basic testing has been done. There's a fair amount of hardware
that uses this sensor, and which also runs Linux, which should eventually
be able to use this driver.
One portability note may be of special interest. It turns out that not all
SPI controllers are happy issuing requests that do things like "write 8 bit
command, read 12 bit response". Most of them seem happy to handle various
word sizes, so the issue isn't "12 bit response" but rather "different rx
and tx write sizes", despite that being a common MicroWire convention. So
this version of the driver no longer reads 12 bit native-endian words; it
reads 16-bit big-endian responses, then byteswaps them and shifts the
results to discard the noise.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).
- It's still less than 2KB of ".text" (ARM). If there's got to be a
mid-layer for something so simple, that's the right size budget. :)
- The guts use board-specific SPI device tables to build the driver
model tree. (Hardware probing is rarely an option.)
- This version of Kconfig includes no drivers. At this writing there
are two known master controller drivers (PXA/SSP, OMAP MicroWire)
and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
mentions of other drivers in development.
- No userspace API. There are several implementations to compare.
Implement them like any other driver, and bind them with sysfs.
The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:
- One bugfix (removes a FIXME), with the visible effect of making device
names be "spiB.C" where B is the bus number and C is the chipselect.
- The "caller provides DMA mappings" mechanism now has kerneldoc, for
DMA drivers that want to be fancy.
- Hey, the framework init can be subsys_init. Even though board init
logic fires earlier, at arch_init ... since the framework init is
for driver support, and the board init support uses static init.
- Various additional spec/doc clarifications based on discussions
with other folk. It adds a brief "thank you" at the end, for folk
who've helped nudge this framework into existence.
As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.
From: Mark Underwood <basicmark@yahoo.com>
Update the SPI framework to remove a potential priority inversion case by
reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On PowerPC, we want to be able to provide an AT_PLATFORM aux table
entry to userspace, so that glibc can choose optimized libraries for
the processor we're running on. Unfortunately that would be the 21st
aux table entry on powerpc, meaning that the aux table including the
terminating null entry would overflow the mm->saved_auxv[] array,
leading to userland programs segfaulting.
This increases the size of the mm->saved_auxv array to be large enough
to accommodate an AT_PLATFORM entry on powerpc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comments in ieee80211.h claim that one doesn't need to set the len
parameter of the stats struct. But if one doesn't, the management frames
are read far over the memory they actually occupy causing badness.
Signed-Off-By: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make the driver produce the string used by phy_connect and have board specific
code pass the integer mii bus id and phy device id for the specific controller
instance.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add the PHY_ID_FMT macro to ensure that the format of the id string used by a
driver to match to its specific phy is consistent between the mdio_bus and the
driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
We can now have the gianfar mii platform device have a proper resource for the
IO memory region for its registers. Previously we passed this information
that the platform_data structure because we couldn't handle overlapping memory
regions for platform devices.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There's a problem with the REQ_BLOCK_PC handling as well (bad ->data_len
handling) where it could actually complete a request ahead of time. I
suggest we just back this out for now, I will resubmit it later when I'm
fully confident in it.
This reverts commit 8672d57138
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
function arguments can't be inline, TYVM...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
extern declaration of static object removed from header
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
extern declaration of static object removed from header
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
in amigahw.h custom renamed to amiga_custom, in drivers with few instances the
same replacement, in the rest - #define custom amiga_custom in driver itself
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
move the sanity check for NR_IRQS being no more than 1<<HARDIRQ_BITS from
asm-m68k/hardirq.h to asm-m68k/irq.h; needed since NR_IRQS is not necessary
know at the points of inclusion of asm/hardirq.h due to the rather ugly header
dependencies on m68k. Fix is by far simpler than trying to massage those
dependencies...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
{get,put}_thread_info() were introduced in 2.5.4 and never
had been called by anything in the tree.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
on ia64 thread_info is at the constant offset from task_struct and stack
is embedded into the same beast. Set __HAVE_THREAD_FUNCTIONS, made
task_thread_info() just add a constant.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cris KSTK_EIP looked for pt_regs at the right offset but from the wrong
place - forgotten ->thread_info
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Al Viro <viro@ftp.linux.org.uk>
task_pt_regs() needs the same offset-by-8 to match copy_thread()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
