# # EDAC Kconfig # Copyright (c) 2008 Doug Thompson www.softwarebitmaker.com # Licensed and distributed under the GPL config EDAC_ATOMIC_SCRUB bool config EDAC_SUPPORT bool menuconfig EDAC tristate "EDAC (Error Detection And Correction) reporting" depends on HAS_IOMEM && EDAC_SUPPORT && RAS help EDAC is a subsystem along with hardware-specific drivers designed to report hardware errors. These are low-level errors that are reported in the CPU or supporting chipset or other subsystems: memory errors, cache errors, PCI errors, thermal throttling, etc.. If unsure, select 'Y'. The mailing list for the EDAC project is linux-edac@vger.kernel.org. if EDAC config EDAC_QGKI bool "Enable QGKI features for EDAC" depends on QGKI help When QGKI variants are selected, use special EDAC features like creating and using deferred work. This feature adds a deferrable timer if the error checking is not worth waking up the cpu from idle. config EDAC_LEGACY_SYSFS bool "EDAC legacy sysfs" default y help Enable the compatibility sysfs nodes. Use 'Y' if your edac utilities aren't ported to work with the newer structures. config EDAC_DEBUG bool "Debugging" select DEBUG_FS help This turns on debugging information for the entire EDAC subsystem. You do so by inserting edac_module with "edac_debug_level=x." Valid levels are 0-4 (from low to high) and by default it is set to 2. Usually you should select 'N' here. config EDAC_DECODE_MCE tristate "Decode MCEs in human-readable form (only on AMD for now)" depends on CPU_SUP_AMD && X86_MCE_AMD default y ---help--- Enable this option if you want to decode Machine Check Exceptions occurring on your machine in human-readable form. You should definitely say Y here in case you want to decode MCEs which occur really early upon boot, before the module infrastructure has been initialized. config EDAC_GHES bool "Output ACPI APEI/GHES BIOS detected errors via EDAC" depends on ACPI_APEI_GHES && (EDAC=y) help Not all machines support hardware-driven error report. Some of those provide a BIOS-driven error report mechanism via ACPI, using the APEI/GHES driver. By enabling this option, the error reports provided by GHES are sent to userspace via the EDAC API. When this option is enabled, it will disable the hardware-driven mechanisms, if a GHES BIOS is detected, entering into the "Firmware First" mode. It should be noticed that keeping both GHES and a hardware-driven error mechanism won't work well, as BIOS will race with OS, while reading the error registers. So, if you want to not use "Firmware first" GHES error mechanism, you should disable GHES either at compilation time or by passing "ghes.disable=1" Kernel parameter at boot time. In doubt, say 'Y'. config EDAC_AMD64 tristate "AMD64 (Opteron, Athlon64)" depends on AMD_NB && EDAC_DECODE_MCE help Support for error detection and correction of DRAM ECC errors on the AMD64 families (>= K8) of memory controllers. config EDAC_AMD64_ERROR_INJECTION bool "Sysfs HW Error injection facilities" depends on EDAC_AMD64 help Recent Opterons (Family 10h and later) provide for Memory Error Injection into the ECC detection circuits. The amd64_edac module allows the operator/user to inject Uncorrectable and Correctable errors into DRAM. When enabled, in each of the respective memory controller directories (/sys/devices/system/edac/mc/mcX), there are 3 input files: - inject_section (0..3, 16-byte section of 64-byte cacheline), - inject_word (0..8, 16-bit word of 16-byte section), - inject_ecc_vector (hex ecc vector: select bits of inject word) In addition, there are two control files, inject_read and inject_write, which trigger the DRAM ECC Read and Write respectively. config EDAC_AMD76X tristate "AMD 76x (760, 762, 768)" depends on PCI && X86_32 help Support for error detection and correction on the AMD 76x series of chipsets used with the Athlon processor. config EDAC_E7XXX tristate "Intel e7xxx (e7205, e7500, e7501, e7505)" depends on PCI && X86_32 help Support for error detection and correction on the Intel E7205, E7500, E7501 and E7505 server chipsets. config EDAC_E752X tristate "Intel e752x (e7520, e7525, e7320) and 3100" depends on PCI && X86 help Support for error detection and correction on the Intel E7520, E7525, E7320 server chipsets. config EDAC_I82443BXGX tristate "Intel 82443BX/GX (440BX/GX)" depends on PCI && X86_32 depends on BROKEN help Support for error detection and correction on the Intel 82443BX/GX memory controllers (440BX/GX chipsets). config EDAC_I82875P tristate "Intel 82875p (D82875P, E7210)" depends on PCI && X86_32 help Support for error detection and correction on the Intel DP82785P and E7210 server chipsets. config EDAC_I82975X tristate "Intel 82975x (D82975x)" depends on PCI && X86 help Support for error detection and correction on the Intel DP82975x server chipsets. config EDAC_I3000 tristate "Intel 3000/3010" depends on PCI && X86 help Support for error detection and correction on the Intel 3000 and 3010 server chipsets. config EDAC_I3200 tristate "Intel 3200" depends on PCI && X86 help Support for error detection and correction on the Intel 3200 and 3210 server chipsets. config EDAC_IE31200 tristate "Intel e312xx" depends on PCI && X86 help Support for error detection and correction on the Intel E3-1200 based DRAM controllers. config EDAC_X38 tristate "Intel X38" depends on PCI && X86 help Support for error detection and correction on the Intel X38 server chipsets. config EDAC_I5400 tristate "Intel 5400 (Seaburg) chipsets" depends on PCI && X86 help Support for error detection and correction the Intel i5400 MCH chipset (Seaburg). config EDAC_I7CORE tristate "Intel i7 Core (Nehalem) processors" depends on PCI && X86 && X86_MCE_INTEL help Support for error detection and correction the Intel i7 Core (Nehalem) Integrated Memory Controller that exists on newer processors like i7 Core, i7 Core Extreme, Xeon 35xx and Xeon 55xx processors. config EDAC_I82860 tristate "Intel 82860" depends on PCI && X86_32 help Support for error detection and correction on the Intel 82860 chipset. config EDAC_R82600 tristate "Radisys 82600 embedded chipset" depends on PCI && X86_32 help Support for error detection and correction on the Radisys 82600 embedded chipset. config EDAC_I5000 tristate "Intel Greencreek/Blackford chipset" depends on X86 && PCI help Support for error detection and correction the Intel Greekcreek/Blackford chipsets. config EDAC_I5100 tristate "Intel San Clemente MCH" depends on X86 && PCI help Support for error detection and correction the Intel San Clemente MCH. config EDAC_I7300 tristate "Intel Clarksboro MCH" depends on X86 && PCI help Support for error detection and correction the Intel Clarksboro MCH (Intel 7300 chipset). config EDAC_SBRIDGE tristate "Intel Sandy-Bridge/Ivy-Bridge/Haswell Integrated MC" depends on PCI && X86_64 && X86_MCE_INTEL && PCI_MMCONFIG help Support for error detection and correction the Intel Sandy Bridge, Ivy Bridge and Haswell Integrated Memory Controllers. config EDAC_SKX tristate "Intel Skylake server Integrated MC" depends on PCI && X86_64 && X86_MCE_INTEL && PCI_MMCONFIG && ACPI depends on ACPI_NFIT || !ACPI_NFIT # if ACPI_NFIT=m, EDAC_SKX can't be y select DMI select ACPI_ADXL help Support for error detection and correction the Intel Skylake server Integrated Memory Controllers. If your system has non-volatile DIMMs you should also manually select CONFIG_ACPI_NFIT. config EDAC_I10NM tristate "Intel 10nm server Integrated MC" depends on PCI && X86_64 && X86_MCE_INTEL && PCI_MMCONFIG && ACPI depends on ACPI_NFIT || !ACPI_NFIT # if ACPI_NFIT=m, EDAC_I10NM can't be y select DMI select ACPI_ADXL help Support for error detection and correction the Intel 10nm server Integrated Memory Controllers. If your system has non-volatile DIMMs you should also manually select CONFIG_ACPI_NFIT. config EDAC_PND2 tristate "Intel Pondicherry2" depends on PCI && X86_64 && X86_MCE_INTEL help Support for error detection and correction on the Intel Pondicherry2 Integrated Memory Controller. This SoC IP is first used on the Apollo Lake platform and Denverton micro-server but may appear on others in the future. config EDAC_MPC85XX bool "Freescale MPC83xx / MPC85xx" depends on FSL_SOC && EDAC=y help Support for error detection and correction on the Freescale MPC8349, MPC8560, MPC8540, MPC8548, T4240 config EDAC_LAYERSCAPE tristate "Freescale Layerscape DDR" depends on ARCH_LAYERSCAPE || SOC_LS1021A help Support for error detection and correction on Freescale memory controllers on Layerscape SoCs. config EDAC_MV64X60 tristate "Marvell MV64x60" depends on MV64X60 help Support for error detection and correction on the Marvell MV64360 and MV64460 chipsets. config EDAC_PASEMI tristate "PA Semi PWRficient" depends on PPC_PASEMI && PCI help Support for error detection and correction on PA Semi PWRficient. config EDAC_CELL tristate "Cell Broadband Engine memory controller" depends on PPC_CELL_COMMON help Support for error detection and correction on the Cell Broadband Engine internal memory controller on platform without a hypervisor config EDAC_PPC4XX tristate "PPC4xx IBM DDR2 Memory Controller" depends on 4xx help This enables support for EDAC on the ECC memory used with the IBM DDR2 memory controller found in various PowerPC 4xx embedded processors such as the 405EX[r], 440SP, 440SPe, 460EX, 460GT and 460SX. config EDAC_AMD8131 tristate "AMD8131 HyperTransport PCI-X Tunnel" depends on PCI && PPC_MAPLE help Support for error detection and correction on the AMD8131 HyperTransport PCI-X Tunnel chip. Note, add more Kconfig dependency if it's adopted on some machine other than Maple. config EDAC_AMD8111 tristate "AMD8111 HyperTransport I/O Hub" depends on PCI && PPC_MAPLE help Support for error detection and correction on the AMD8111 HyperTransport I/O Hub chip. Note, add more Kconfig dependency if it's adopted on some machine other than Maple. config EDAC_CPC925 tristate "IBM CPC925 Memory Controller (PPC970FX)" depends on PPC64 help Support for error detection and correction on the IBM CPC925 Bridge and Memory Controller, which is a companion chip to the PowerPC 970 family of processors. config EDAC_HIGHBANK_MC tristate "Highbank Memory Controller" depends on ARCH_HIGHBANK help Support for error detection and correction on the Calxeda Highbank memory controller. config EDAC_HIGHBANK_L2 tristate "Highbank L2 Cache" depends on ARCH_HIGHBANK help Support for error detection and correction on the Calxeda Highbank memory controller. config EDAC_OCTEON_PC tristate "Cavium Octeon Primary Caches" depends on CPU_CAVIUM_OCTEON help Support for error detection and correction on the primary caches of the cnMIPS cores of Cavium Octeon family SOCs. config EDAC_OCTEON_L2C tristate "Cavium Octeon Secondary Caches (L2C)" depends on CAVIUM_OCTEON_SOC help Support for error detection and correction on the Cavium Octeon family of SOCs. config EDAC_OCTEON_LMC tristate "Cavium Octeon DRAM Memory Controller (LMC)" depends on CAVIUM_OCTEON_SOC help Support for error detection and correction on the Cavium Octeon family of SOCs. config EDAC_OCTEON_PCI tristate "Cavium Octeon PCI Controller" depends on PCI && CAVIUM_OCTEON_SOC help Support for error detection and correction on the Cavium Octeon family of SOCs. config EDAC_THUNDERX tristate "Cavium ThunderX EDAC" depends on ARM64 depends on PCI help Support for error detection and correction on the Cavium ThunderX memory controllers (LMC), Cache Coherent Processor Interconnect (CCPI) and L2 cache blocks (TAD, CBC, MCI). config EDAC_ALTERA bool "Altera SOCFPGA ECC" depends on EDAC=y && (ARCH_SOCFPGA || ARCH_STRATIX10) help Support for error detection and correction on the Altera SOCs. This is the global enable for the various Altera peripherals. config EDAC_ALTERA_SDRAM bool "Altera SDRAM ECC" depends on EDAC_ALTERA=y help Support for error detection and correction on the Altera SDRAM Memory for Altera SoCs. Note that the preloader must initialize the SDRAM before loading the kernel. config EDAC_ALTERA_L2C bool "Altera L2 Cache ECC" depends on EDAC_ALTERA=y && CACHE_L2X0 help Support for error detection and correction on the Altera L2 cache Memory for Altera SoCs. This option requires L2 cache. config EDAC_ALTERA_OCRAM bool "Altera On-Chip RAM ECC" depends on EDAC_ALTERA=y && SRAM && GENERIC_ALLOCATOR help Support for error detection and correction on the Altera On-Chip RAM Memory for Altera SoCs. config EDAC_ALTERA_ETHERNET bool "Altera Ethernet FIFO ECC" depends on EDAC_ALTERA=y help Support for error detection and correction on the Altera Ethernet FIFO Memory for Altera SoCs. config EDAC_ALTERA_NAND bool "Altera NAND FIFO ECC" depends on EDAC_ALTERA=y && MTD_NAND_DENALI help Support for error detection and correction on the Altera NAND FIFO Memory for Altera SoCs. config EDAC_ALTERA_DMA bool "Altera DMA FIFO ECC" depends on EDAC_ALTERA=y && PL330_DMA=y help Support for error detection and correction on the Altera DMA FIFO Memory for Altera SoCs. config EDAC_ALTERA_USB bool "Altera USB FIFO ECC" depends on EDAC_ALTERA=y && USB_DWC2 help Support for error detection and correction on the Altera USB FIFO Memory for Altera SoCs. config EDAC_ALTERA_QSPI bool "Altera QSPI FIFO ECC" depends on EDAC_ALTERA=y && SPI_CADENCE_QUADSPI help Support for error detection and correction on the Altera QSPI FIFO Memory for Altera SoCs. config EDAC_ALTERA_SDMMC bool "Altera SDMMC FIFO ECC" depends on EDAC_ALTERA=y && MMC_DW help Support for error detection and correction on the Altera SDMMC FIFO Memory for Altera SoCs. config EDAC_SIFIVE bool "Sifive platform EDAC driver" depends on EDAC=y && RISCV help Support for error detection and correction on the SiFive SoCs. config EDAC_ARMADA_XP bool "Marvell Armada XP DDR and L2 Cache ECC" depends on MACH_MVEBU_V7 help Support for error correction and detection on the Marvell Aramada XP DDR RAM and L2 cache controllers. config EDAC_SYNOPSYS tristate "Synopsys DDR Memory Controller" depends on ARCH_ZYNQ || ARCH_ZYNQMP help Support for error detection and correction on the Synopsys DDR memory controller. config EDAC_XGENE tristate "APM X-Gene SoC" depends on (ARM64 || COMPILE_TEST) help Support for error detection and correction on the APM X-Gene family of SOCs. config EDAC_TI tristate "Texas Instruments DDR3 ECC Controller" depends on ARCH_KEYSTONE || SOC_DRA7XX help Support for error detection and correction on the TI SoCs. config EDAC_PANIC_ON_CE depends on EDAC bool "Panic on correctable errors" help Forcibly cause a kernel panic if an correctable error (CE) is detected, even though the error is (by definition) correctable and would otherwise result in no adverse system effects. This feature reduce debugging times on hardware which may be operating at voltages or frequencies outside normal specification. For production builds, you should say 'N' here. config EDAC_KRYO_ARM64 depends on ARM64 tristate "ARM KRYO Gold and Silver L1/L2/L3/SCU Caches" help Support for error detection and correction on the Kryo3xx Gold and Silver CPUs. Reports errors caught by Kryo3xx ECC mechanism. For debugging issues having to do with stability and overall system health, you should probably say 'Y' here. config EDAC_KRYO_ARM64_PANIC_ON_CE depends on EDAC_KRYO_ARM64 select EDAC_PANIC_ON_CE bool "Panic on correctable errors - Kryo" help Forcibly cause a kernel panic on kryo if an correctable error (CE) is detected, even though the error is (by definition) correctable and would otherwise result in no adverse system effects. This can reduce debugging times on hardware which may be operating at voltages or frequencies outside normal specification. For production builds, you should definitely say 'N' here. config EDAC_KRYO_ARM64_PANIC_ON_UE depends on EDAC_KRYO_ARM64 bool "Panic on uncorrectable errors - kryo" help Forcibly cause a kernel panic if an uncorrectable error (UE) is detected. This can reduce debugging times on hardware which may be operating at voltages or frequencies outside normal specification. For production builds, you should probably say 'N' here. config EDAC_QCOM tristate "QCOM EDAC Controller" depends on ARCH_QCOM && QCOM_LLCC help Support for error detection and correction on the Qualcomm Technologies, Inc. SoCs. This driver reports Single Bit Errors (SBEs) and Double Bit Errors (DBEs). As of now, it supports error reporting for Last Level Cache Controller (LLCC) of Tag RAM and Data RAM. For debugging issues having to do with stability and overall system health, you should probably say 'Y' here. config EDAC_QCOM_LLCC_PANIC_ON_CE depends on EDAC_QCOM select EDAC_PANIC_ON_CE bool "panic on correctable errors - qcom llcc" help Forcibly cause kernel panic if a correctable error (CE) is detected, even though the error is (by definition) correctable and would otherwise result in no adverse system effects. This can reduce debugging times on hardware which my be operating at voltages or frequencies outside normal specifications. For production builds, you should definitely say 'N' here. config EDAC_QCOM_LLCC_PANIC_ON_UE depends on EDAC_QCOM bool "Panic on uncorrectable errors - qcom llcc" help Forcibly cause a kernel panic if an uncorrectable error (UE) is detected. This can reduce debugging times on hardware which may be operating at voltages or frequencies outside normal specification. For production builds, you should probably say 'N' here. config EDAC_ASPEED tristate "Aspeed AST 2500 SoC" depends on MACH_ASPEED_G5 help Support for error detection and correction on the Aspeed AST 2500 SoC. First, ECC must be configured in the bootloader. Then, this driver will expose error counters via the EDAC kernel framework. config EDAC_BLUEFIELD tristate "Mellanox BlueField Memory ECC" depends on ARM64 && ((MELLANOX_PLATFORM && ACPI) || COMPILE_TEST) help Support for error detection and correction on the Mellanox BlueField SoCs. endif # EDAC