39249d776c
PCB120 and PCB123 are both development boards based on Microsemi Ocelot so let's use the same fitImage for both. Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/20871/ Cc: ralf@linux-mips.org Cc: jhogan@kernel.org Cc: robh+dt@kernel.org Cc: mark.rutland@arm.com Cc: davem@davemloft.net Cc: andrew@lunn.ch Cc: f.fainelli@gmail.com Cc: allan.nielsen@microchip.com Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: netdev@vger.kernel.org Cc: thomas.petazzoni@bootlin.com Cc: antoine.tenart@bootlin.com
87 lines
2.6 KiB
Plaintext
87 lines
2.6 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0
|
|
if MIPS_GENERIC
|
|
|
|
config LEGACY_BOARDS
|
|
bool
|
|
help
|
|
Select this from your board if the board must use a legacy, non-UHI,
|
|
boot protocol. This will cause the kernel to scan through the list of
|
|
supported machines calling their detect functions in turn if the
|
|
kernel is booted without being provided with an FDT via the UHI
|
|
boot protocol.
|
|
|
|
config YAMON_DT_SHIM
|
|
bool
|
|
help
|
|
Select this from your board if the board uses the YAMON bootloader
|
|
and you wish to include code which helps translate various
|
|
YAMON-provided environment variables into a device tree properties.
|
|
|
|
comment "Legacy (non-UHI/non-FIT) Boards"
|
|
|
|
config LEGACY_BOARD_SEAD3
|
|
bool "Support MIPS SEAD-3 boards"
|
|
select LEGACY_BOARDS
|
|
select YAMON_DT_SHIM
|
|
help
|
|
Enable this to include support for booting on MIPS SEAD-3 FPGA-based
|
|
development boards, which boot using a legacy boot protocol.
|
|
|
|
comment "MSCC Ocelot doesn't work with SEAD3 enabled"
|
|
depends on LEGACY_BOARD_SEAD3
|
|
|
|
config LEGACY_BOARD_OCELOT
|
|
bool "Support MSCC Ocelot boards"
|
|
depends on LEGACY_BOARD_SEAD3=n
|
|
select LEGACY_BOARDS
|
|
select MSCC_OCELOT
|
|
select SYS_HAS_EARLY_PRINTK
|
|
select USE_GENERIC_EARLY_PRINTK_8250
|
|
|
|
config MSCC_OCELOT
|
|
bool
|
|
select GPIOLIB
|
|
select MSCC_OCELOT_IRQ
|
|
|
|
comment "FIT/UHI Boards"
|
|
|
|
config FIT_IMAGE_FDT_BOSTON
|
|
bool "Include FDT for MIPS Boston boards"
|
|
help
|
|
Enable this to include the FDT for the MIPS Boston development board
|
|
from Imagination Technologies in the FIT kernel image. You should
|
|
enable this if you wish to boot on a MIPS Boston board, as it is
|
|
expected by the bootloader.
|
|
|
|
config FIT_IMAGE_FDT_NI169445
|
|
bool "Include FDT for NI 169445"
|
|
help
|
|
Enable this to include the FDT for the 169445 platform from
|
|
National Instruments in the FIT kernel image.
|
|
|
|
config FIT_IMAGE_FDT_XILFPGA
|
|
bool "Include FDT for Xilfpga"
|
|
help
|
|
Enable this to include the FDT for the MIPSfpga platform
|
|
from Imagination Technologies in the FIT kernel image.
|
|
|
|
config FIT_IMAGE_FDT_OCELOT
|
|
bool "Include FDT for Microsemi Ocelot development platforms"
|
|
select MSCC_OCELOT
|
|
help
|
|
Enable this to include the FDT for the Ocelot development platforms
|
|
from Microsemi in the FIT kernel image.
|
|
This requires u-boot on the platform.
|
|
|
|
config VIRT_BOARD_RANCHU
|
|
bool "Support Ranchu platform for Android emulator"
|
|
help
|
|
This enables support for the platform used by Android emulator.
|
|
|
|
Ranchu platform consists of a set of virtual devices. This platform
|
|
enables emulation of variety of virtual configurations while using
|
|
Android emulator. Android emulator is based on Qemu, and contains
|
|
the support for the same set of virtual devices.
|
|
|
|
endif
|