fa873e9030
[ Upstream commit 0f5cc249ff73552d3bd864e62f85841dafaa107d ] max_low_pfn variable is incorrectly adjusted if the kernel is built with high memory support and the later is detected in a running system, so the memory which actually can be directly mapped is getting into the highmem zone. See the ZONE_NORMAL range on my MIPS32r5 system: > Zone ranges: > DMA [mem 0x0000000000000000-0x0000000000ffffff] > Normal [mem 0x0000000001000000-0x0000000007ffffff] > HighMem [mem 0x0000000008000000-0x000000020fffffff] while the zones are supposed to look as follows: > Zone ranges: > DMA [mem 0x0000000000000000-0x0000000000ffffff] > Normal [mem 0x0000000001000000-0x000000001fffffff] > HighMem [mem 0x0000000020000000-0x000000020fffffff] Even though the physical memory within the range [0x08000000;0x20000000] belongs to MMIO on our system, we don't really want it to be considered as high memory since on MIPS32 that range still can be directly mapped. Note there might be other problems caused by the max_low_pfn variable misconfiguration. For instance high_memory variable is initialize with virtual address corresponding to the max_low_pfn PFN, and by design it must define the upper bound on direct map memory, then end of the normal zone. That in its turn potentially may cause problems in accessing the memory by means of the /dev/mem and /dev/kmem devices. Let's fix the discovered misconfiguration then. It turns out the commita94e4f24ec
("MIPS: init: Drop boot_mem_map") didn't introduce the max_low_pfn adjustment quite correct. If the kernel is built with high memory support and the system is equipped with high memory, the max_low_pfn variable will need to be initialized with PFN of the most upper directly reachable memory address so the zone normal would be correctly setup. On MIPS that PFN corresponds to PFN_DOWN(HIGHMEM_START). If the system is built with no high memory support and one is detected in the running system, we'll just need to adjust the max_pfn variable to discard the found high memory from the system and leave the max_low_pfn as is, since the later will be less than PFN_DOWN(HIGHMEM_START) anyway by design of the for_each_memblock() loop performed a bit early in the bootmem_init() method. Fixes:a94e4f24ec
("MIPS: init: Drop boot_mem_map") Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
828 lines
21 KiB
C
828 lines
21 KiB
C
/*
|
|
* This file is subject to the terms and conditions of the GNU General Public
|
|
* License. See the file "COPYING" in the main directory of this archive
|
|
* for more details.
|
|
*
|
|
* Copyright (C) 1995 Linus Torvalds
|
|
* Copyright (C) 1995 Waldorf Electronics
|
|
* Copyright (C) 1994, 95, 96, 97, 98, 99, 2000, 01, 02, 03 Ralf Baechle
|
|
* Copyright (C) 1996 Stoned Elipot
|
|
* Copyright (C) 1999 Silicon Graphics, Inc.
|
|
* Copyright (C) 2000, 2001, 2002, 2007 Maciej W. Rozycki
|
|
*/
|
|
#include <linux/init.h>
|
|
#include <linux/cpu.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/export.h>
|
|
#include <linux/screen_info.h>
|
|
#include <linux/memblock.h>
|
|
#include <linux/initrd.h>
|
|
#include <linux/root_dev.h>
|
|
#include <linux/highmem.h>
|
|
#include <linux/console.h>
|
|
#include <linux/pfn.h>
|
|
#include <linux/debugfs.h>
|
|
#include <linux/kexec.h>
|
|
#include <linux/sizes.h>
|
|
#include <linux/device.h>
|
|
#include <linux/dma-contiguous.h>
|
|
#include <linux/decompress/generic.h>
|
|
#include <linux/of_fdt.h>
|
|
#include <linux/of_reserved_mem.h>
|
|
|
|
#include <asm/addrspace.h>
|
|
#include <asm/bootinfo.h>
|
|
#include <asm/bugs.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/cdmm.h>
|
|
#include <asm/cpu.h>
|
|
#include <asm/debug.h>
|
|
#include <asm/dma-coherence.h>
|
|
#include <asm/sections.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/smp-ops.h>
|
|
#include <asm/prom.h>
|
|
|
|
#ifdef CONFIG_MIPS_ELF_APPENDED_DTB
|
|
const char __section(.appended_dtb) __appended_dtb[0x100000];
|
|
#endif /* CONFIG_MIPS_ELF_APPENDED_DTB */
|
|
|
|
struct cpuinfo_mips cpu_data[NR_CPUS] __read_mostly;
|
|
|
|
EXPORT_SYMBOL(cpu_data);
|
|
|
|
#ifdef CONFIG_VT
|
|
struct screen_info screen_info;
|
|
#endif
|
|
|
|
/*
|
|
* Setup information
|
|
*
|
|
* These are initialized so they are in the .data section
|
|
*/
|
|
unsigned long mips_machtype __read_mostly = MACH_UNKNOWN;
|
|
|
|
EXPORT_SYMBOL(mips_machtype);
|
|
|
|
static char __initdata command_line[COMMAND_LINE_SIZE];
|
|
char __initdata arcs_cmdline[COMMAND_LINE_SIZE];
|
|
|
|
#ifdef CONFIG_CMDLINE_BOOL
|
|
static char __initdata builtin_cmdline[COMMAND_LINE_SIZE] = CONFIG_CMDLINE;
|
|
#endif
|
|
|
|
/*
|
|
* mips_io_port_base is the begin of the address space to which x86 style
|
|
* I/O ports are mapped.
|
|
*/
|
|
unsigned long mips_io_port_base = -1;
|
|
EXPORT_SYMBOL(mips_io_port_base);
|
|
|
|
static struct resource code_resource = { .name = "Kernel code", };
|
|
static struct resource data_resource = { .name = "Kernel data", };
|
|
static struct resource bss_resource = { .name = "Kernel bss", };
|
|
|
|
static void *detect_magic __initdata = detect_memory_region;
|
|
|
|
#ifdef CONFIG_MIPS_AUTO_PFN_OFFSET
|
|
unsigned long ARCH_PFN_OFFSET;
|
|
EXPORT_SYMBOL(ARCH_PFN_OFFSET);
|
|
#endif
|
|
|
|
void __init add_memory_region(phys_addr_t start, phys_addr_t size, long type)
|
|
{
|
|
/*
|
|
* Note: This function only exists for historical reason,
|
|
* new code should use memblock_add or memblock_add_node instead.
|
|
*/
|
|
|
|
/*
|
|
* If the region reaches the top of the physical address space, adjust
|
|
* the size slightly so that (start + size) doesn't overflow
|
|
*/
|
|
if (start + size - 1 == PHYS_ADDR_MAX)
|
|
--size;
|
|
|
|
/* Sanity check */
|
|
if (start + size < start) {
|
|
pr_warn("Trying to add an invalid memory region, skipped\n");
|
|
return;
|
|
}
|
|
|
|
if (start < PHYS_OFFSET)
|
|
return;
|
|
|
|
memblock_add(start, size);
|
|
/* Reserve any memory except the ordinary RAM ranges. */
|
|
switch (type) {
|
|
case BOOT_MEM_RAM:
|
|
break;
|
|
|
|
case BOOT_MEM_NOMAP: /* Discard the range from the system. */
|
|
memblock_remove(start, size);
|
|
break;
|
|
|
|
default: /* Reserve the rest of the memory types at boot time */
|
|
memblock_reserve(start, size);
|
|
break;
|
|
}
|
|
}
|
|
|
|
void __init detect_memory_region(phys_addr_t start, phys_addr_t sz_min, phys_addr_t sz_max)
|
|
{
|
|
void *dm = &detect_magic;
|
|
phys_addr_t size;
|
|
|
|
for (size = sz_min; size < sz_max; size <<= 1) {
|
|
if (!memcmp(dm, dm + size, sizeof(detect_magic)))
|
|
break;
|
|
}
|
|
|
|
pr_debug("Memory: %lluMB of RAM detected at 0x%llx (min: %lluMB, max: %lluMB)\n",
|
|
((unsigned long long) size) / SZ_1M,
|
|
(unsigned long long) start,
|
|
((unsigned long long) sz_min) / SZ_1M,
|
|
((unsigned long long) sz_max) / SZ_1M);
|
|
|
|
add_memory_region(start, size, BOOT_MEM_RAM);
|
|
}
|
|
|
|
/*
|
|
* Manage initrd
|
|
*/
|
|
#ifdef CONFIG_BLK_DEV_INITRD
|
|
|
|
static int __init rd_start_early(char *p)
|
|
{
|
|
unsigned long start = memparse(p, &p);
|
|
|
|
#ifdef CONFIG_64BIT
|
|
/* Guess if the sign extension was forgotten by bootloader */
|
|
if (start < XKPHYS)
|
|
start = (int)start;
|
|
#endif
|
|
initrd_start = start;
|
|
initrd_end += start;
|
|
return 0;
|
|
}
|
|
early_param("rd_start", rd_start_early);
|
|
|
|
static int __init rd_size_early(char *p)
|
|
{
|
|
initrd_end += memparse(p, &p);
|
|
return 0;
|
|
}
|
|
early_param("rd_size", rd_size_early);
|
|
|
|
/* it returns the next free pfn after initrd */
|
|
static unsigned long __init init_initrd(void)
|
|
{
|
|
unsigned long end;
|
|
|
|
/*
|
|
* Board specific code or command line parser should have
|
|
* already set up initrd_start and initrd_end. In these cases
|
|
* perfom sanity checks and use them if all looks good.
|
|
*/
|
|
if (!initrd_start || initrd_end <= initrd_start)
|
|
goto disable;
|
|
|
|
if (initrd_start & ~PAGE_MASK) {
|
|
pr_err("initrd start must be page aligned\n");
|
|
goto disable;
|
|
}
|
|
|
|
/*
|
|
* Sanitize initrd addresses. For example firmware
|
|
* can't guess if they need to pass them through
|
|
* 64-bits values if the kernel has been built in pure
|
|
* 32-bit. We need also to switch from KSEG0 to XKPHYS
|
|
* addresses now, so the code can now safely use __pa().
|
|
*/
|
|
end = __pa(initrd_end);
|
|
initrd_end = (unsigned long)__va(end);
|
|
initrd_start = (unsigned long)__va(__pa(initrd_start));
|
|
|
|
if (initrd_start < PAGE_OFFSET) {
|
|
pr_err("initrd start < PAGE_OFFSET\n");
|
|
goto disable;
|
|
}
|
|
|
|
ROOT_DEV = Root_RAM0;
|
|
return PFN_UP(end);
|
|
disable:
|
|
initrd_start = 0;
|
|
initrd_end = 0;
|
|
return 0;
|
|
}
|
|
|
|
/* In some conditions (e.g. big endian bootloader with a little endian
|
|
kernel), the initrd might appear byte swapped. Try to detect this and
|
|
byte swap it if needed. */
|
|
static void __init maybe_bswap_initrd(void)
|
|
{
|
|
#if defined(CONFIG_CPU_CAVIUM_OCTEON)
|
|
u64 buf;
|
|
|
|
/* Check for CPIO signature */
|
|
if (!memcmp((void *)initrd_start, "070701", 6))
|
|
return;
|
|
|
|
/* Check for compressed initrd */
|
|
if (decompress_method((unsigned char *)initrd_start, 8, NULL))
|
|
return;
|
|
|
|
/* Try again with a byte swapped header */
|
|
buf = swab64p((u64 *)initrd_start);
|
|
if (!memcmp(&buf, "070701", 6) ||
|
|
decompress_method((unsigned char *)(&buf), 8, NULL)) {
|
|
unsigned long i;
|
|
|
|
pr_info("Byteswapped initrd detected\n");
|
|
for (i = initrd_start; i < ALIGN(initrd_end, 8); i += 8)
|
|
swab64s((u64 *)i);
|
|
}
|
|
#endif
|
|
}
|
|
|
|
static void __init finalize_initrd(void)
|
|
{
|
|
unsigned long size = initrd_end - initrd_start;
|
|
|
|
if (size == 0) {
|
|
printk(KERN_INFO "Initrd not found or empty");
|
|
goto disable;
|
|
}
|
|
if (__pa(initrd_end) > PFN_PHYS(max_low_pfn)) {
|
|
printk(KERN_ERR "Initrd extends beyond end of memory");
|
|
goto disable;
|
|
}
|
|
|
|
maybe_bswap_initrd();
|
|
|
|
memblock_reserve(__pa(initrd_start), size);
|
|
initrd_below_start_ok = 1;
|
|
|
|
pr_info("Initial ramdisk at: 0x%lx (%lu bytes)\n",
|
|
initrd_start, size);
|
|
return;
|
|
disable:
|
|
printk(KERN_CONT " - disabling initrd\n");
|
|
initrd_start = 0;
|
|
initrd_end = 0;
|
|
}
|
|
|
|
#else /* !CONFIG_BLK_DEV_INITRD */
|
|
|
|
static unsigned long __init init_initrd(void)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
#define finalize_initrd() do {} while (0)
|
|
|
|
#endif
|
|
|
|
/*
|
|
* Initialize the bootmem allocator. It also setup initrd related data
|
|
* if needed.
|
|
*/
|
|
#if defined(CONFIG_SGI_IP27) || (defined(CONFIG_CPU_LOONGSON3) && defined(CONFIG_NUMA))
|
|
|
|
static void __init bootmem_init(void)
|
|
{
|
|
init_initrd();
|
|
finalize_initrd();
|
|
}
|
|
|
|
#else /* !CONFIG_SGI_IP27 */
|
|
|
|
static void __init bootmem_init(void)
|
|
{
|
|
struct memblock_region *mem;
|
|
phys_addr_t ramstart, ramend;
|
|
|
|
ramstart = memblock_start_of_DRAM();
|
|
ramend = memblock_end_of_DRAM();
|
|
|
|
/*
|
|
* Sanity check any INITRD first. We don't take it into account
|
|
* for bootmem setup initially, rely on the end-of-kernel-code
|
|
* as our memory range starting point. Once bootmem is inited we
|
|
* will reserve the area used for the initrd.
|
|
*/
|
|
init_initrd();
|
|
|
|
/* Reserve memory occupied by kernel. */
|
|
memblock_reserve(__pa_symbol(&_text),
|
|
__pa_symbol(&_end) - __pa_symbol(&_text));
|
|
|
|
/* max_low_pfn is not a number of pages but the end pfn of low mem */
|
|
|
|
#ifdef CONFIG_MIPS_AUTO_PFN_OFFSET
|
|
ARCH_PFN_OFFSET = PFN_UP(ramstart);
|
|
#else
|
|
/*
|
|
* Reserve any memory between the start of RAM and PHYS_OFFSET
|
|
*/
|
|
if (ramstart > PHYS_OFFSET)
|
|
memblock_reserve(PHYS_OFFSET, ramstart - PHYS_OFFSET);
|
|
|
|
if (PFN_UP(ramstart) > ARCH_PFN_OFFSET) {
|
|
pr_info("Wasting %lu bytes for tracking %lu unused pages\n",
|
|
(unsigned long)((PFN_UP(ramstart) - ARCH_PFN_OFFSET) * sizeof(struct page)),
|
|
(unsigned long)(PFN_UP(ramstart) - ARCH_PFN_OFFSET));
|
|
}
|
|
#endif
|
|
|
|
min_low_pfn = ARCH_PFN_OFFSET;
|
|
max_pfn = PFN_DOWN(ramend);
|
|
for_each_memblock(memory, mem) {
|
|
unsigned long start = memblock_region_memory_base_pfn(mem);
|
|
unsigned long end = memblock_region_memory_end_pfn(mem);
|
|
|
|
/*
|
|
* Skip highmem here so we get an accurate max_low_pfn if low
|
|
* memory stops short of high memory.
|
|
* If the region overlaps HIGHMEM_START, end is clipped so
|
|
* max_pfn excludes the highmem portion.
|
|
*/
|
|
if (memblock_is_nomap(mem))
|
|
continue;
|
|
if (start >= PFN_DOWN(HIGHMEM_START))
|
|
continue;
|
|
if (end > PFN_DOWN(HIGHMEM_START))
|
|
end = PFN_DOWN(HIGHMEM_START);
|
|
if (end > max_low_pfn)
|
|
max_low_pfn = end;
|
|
}
|
|
|
|
if (min_low_pfn >= max_low_pfn)
|
|
panic("Incorrect memory mapping !!!");
|
|
|
|
if (max_pfn > PFN_DOWN(HIGHMEM_START)) {
|
|
max_low_pfn = PFN_DOWN(HIGHMEM_START);
|
|
#ifdef CONFIG_HIGHMEM
|
|
highstart_pfn = max_low_pfn;
|
|
highend_pfn = max_pfn;
|
|
#else
|
|
max_pfn = max_low_pfn;
|
|
#endif
|
|
}
|
|
|
|
|
|
/*
|
|
* In any case the added to the memblock memory regions
|
|
* (highmem/lowmem, available/reserved, etc) are considered
|
|
* as present, so inform sparsemem about them.
|
|
*/
|
|
memblocks_present();
|
|
|
|
/*
|
|
* Reserve initrd memory if needed.
|
|
*/
|
|
finalize_initrd();
|
|
}
|
|
|
|
#endif /* CONFIG_SGI_IP27 */
|
|
|
|
static int usermem __initdata;
|
|
|
|
static int __init early_parse_mem(char *p)
|
|
{
|
|
phys_addr_t start, size;
|
|
|
|
/*
|
|
* If a user specifies memory size, we
|
|
* blow away any automatically generated
|
|
* size.
|
|
*/
|
|
if (usermem == 0) {
|
|
usermem = 1;
|
|
memblock_remove(memblock_start_of_DRAM(),
|
|
memblock_end_of_DRAM() - memblock_start_of_DRAM());
|
|
}
|
|
start = 0;
|
|
size = memparse(p, &p);
|
|
if (*p == '@')
|
|
start = memparse(p + 1, &p);
|
|
|
|
add_memory_region(start, size, BOOT_MEM_RAM);
|
|
|
|
return 0;
|
|
}
|
|
early_param("mem", early_parse_mem);
|
|
|
|
static int __init early_parse_memmap(char *p)
|
|
{
|
|
char *oldp;
|
|
u64 start_at, mem_size;
|
|
|
|
if (!p)
|
|
return -EINVAL;
|
|
|
|
if (!strncmp(p, "exactmap", 8)) {
|
|
pr_err("\"memmap=exactmap\" invalid on MIPS\n");
|
|
return 0;
|
|
}
|
|
|
|
oldp = p;
|
|
mem_size = memparse(p, &p);
|
|
if (p == oldp)
|
|
return -EINVAL;
|
|
|
|
if (*p == '@') {
|
|
start_at = memparse(p+1, &p);
|
|
add_memory_region(start_at, mem_size, BOOT_MEM_RAM);
|
|
} else if (*p == '#') {
|
|
pr_err("\"memmap=nn#ss\" (force ACPI data) invalid on MIPS\n");
|
|
return -EINVAL;
|
|
} else if (*p == '$') {
|
|
start_at = memparse(p+1, &p);
|
|
add_memory_region(start_at, mem_size, BOOT_MEM_RESERVED);
|
|
} else {
|
|
pr_err("\"memmap\" invalid format!\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (*p == '\0') {
|
|
usermem = 1;
|
|
return 0;
|
|
} else
|
|
return -EINVAL;
|
|
}
|
|
early_param("memmap", early_parse_memmap);
|
|
|
|
#ifdef CONFIG_PROC_VMCORE
|
|
unsigned long setup_elfcorehdr, setup_elfcorehdr_size;
|
|
static int __init early_parse_elfcorehdr(char *p)
|
|
{
|
|
struct memblock_region *mem;
|
|
|
|
setup_elfcorehdr = memparse(p, &p);
|
|
|
|
for_each_memblock(memory, mem) {
|
|
unsigned long start = mem->base;
|
|
unsigned long end = start + mem->size;
|
|
if (setup_elfcorehdr >= start && setup_elfcorehdr < end) {
|
|
/*
|
|
* Reserve from the elf core header to the end of
|
|
* the memory segment, that should all be kdump
|
|
* reserved memory.
|
|
*/
|
|
setup_elfcorehdr_size = end - setup_elfcorehdr;
|
|
break;
|
|
}
|
|
}
|
|
/*
|
|
* If we don't find it in the memory map, then we shouldn't
|
|
* have to worry about it, as the new kernel won't use it.
|
|
*/
|
|
return 0;
|
|
}
|
|
early_param("elfcorehdr", early_parse_elfcorehdr);
|
|
#endif
|
|
|
|
#ifdef CONFIG_KEXEC
|
|
static void __init mips_parse_crashkernel(void)
|
|
{
|
|
unsigned long long total_mem;
|
|
unsigned long long crash_size, crash_base;
|
|
int ret;
|
|
|
|
total_mem = memblock_phys_mem_size();
|
|
ret = parse_crashkernel(boot_command_line, total_mem,
|
|
&crash_size, &crash_base);
|
|
if (ret != 0 || crash_size <= 0)
|
|
return;
|
|
|
|
if (!memblock_find_in_range(crash_base, crash_base + crash_size, crash_size, 1)) {
|
|
pr_warn("Invalid memory region reserved for crash kernel\n");
|
|
return;
|
|
}
|
|
|
|
crashk_res.start = crash_base;
|
|
crashk_res.end = crash_base + crash_size - 1;
|
|
}
|
|
|
|
static void __init request_crashkernel(struct resource *res)
|
|
{
|
|
int ret;
|
|
|
|
if (crashk_res.start == crashk_res.end)
|
|
return;
|
|
|
|
ret = request_resource(res, &crashk_res);
|
|
if (!ret)
|
|
pr_info("Reserving %ldMB of memory at %ldMB for crashkernel\n",
|
|
(unsigned long)((crashk_res.end -
|
|
crashk_res.start + 1) >> 20),
|
|
(unsigned long)(crashk_res.start >> 20));
|
|
}
|
|
#else /* !defined(CONFIG_KEXEC) */
|
|
static void __init mips_parse_crashkernel(void)
|
|
{
|
|
}
|
|
|
|
static void __init request_crashkernel(struct resource *res)
|
|
{
|
|
}
|
|
#endif /* !defined(CONFIG_KEXEC) */
|
|
|
|
static void __init check_kernel_sections_mem(void)
|
|
{
|
|
phys_addr_t start = __pa_symbol(&_text);
|
|
phys_addr_t size = __pa_symbol(&_end) - start;
|
|
|
|
if (!memblock_is_region_memory(start, size)) {
|
|
pr_info("Kernel sections are not in the memory maps\n");
|
|
memblock_add(start, size);
|
|
}
|
|
}
|
|
|
|
#define USE_PROM_CMDLINE IS_ENABLED(CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER)
|
|
#define USE_DTB_CMDLINE IS_ENABLED(CONFIG_MIPS_CMDLINE_FROM_DTB)
|
|
#define EXTEND_WITH_PROM IS_ENABLED(CONFIG_MIPS_CMDLINE_DTB_EXTEND)
|
|
#define BUILTIN_EXTEND_WITH_PROM \
|
|
IS_ENABLED(CONFIG_MIPS_CMDLINE_BUILTIN_EXTEND)
|
|
|
|
/*
|
|
* arch_mem_init - initialize memory management subsystem
|
|
*
|
|
* o plat_mem_setup() detects the memory configuration and will record detected
|
|
* memory areas using add_memory_region.
|
|
*
|
|
* At this stage the memory configuration of the system is known to the
|
|
* kernel but generic memory management system is still entirely uninitialized.
|
|
*
|
|
* o bootmem_init()
|
|
* o sparse_init()
|
|
* o paging_init()
|
|
* o dma_contiguous_reserve()
|
|
*
|
|
* At this stage the bootmem allocator is ready to use.
|
|
*
|
|
* NOTE: historically plat_mem_setup did the entire platform initialization.
|
|
* This was rather impractical because it meant plat_mem_setup had to
|
|
* get away without any kind of memory allocator. To keep old code from
|
|
* breaking plat_setup was just renamed to plat_mem_setup and a second platform
|
|
* initialization hook for anything else was introduced.
|
|
*/
|
|
static void __init arch_mem_init(char **cmdline_p)
|
|
{
|
|
extern void plat_mem_setup(void);
|
|
|
|
/*
|
|
* Initialize boot_command_line to an innocuous but non-empty string in
|
|
* order to prevent early_init_dt_scan_chosen() from copying
|
|
* CONFIG_CMDLINE into it without our knowledge. We handle
|
|
* CONFIG_CMDLINE ourselves below & don't want to duplicate its
|
|
* content because repeating arguments can be problematic.
|
|
*/
|
|
strlcpy(boot_command_line, " ", COMMAND_LINE_SIZE);
|
|
|
|
/* call board setup routine */
|
|
plat_mem_setup();
|
|
memblock_set_bottom_up(true);
|
|
|
|
#if defined(CONFIG_CMDLINE_BOOL) && defined(CONFIG_CMDLINE_OVERRIDE)
|
|
strlcpy(boot_command_line, builtin_cmdline, COMMAND_LINE_SIZE);
|
|
#else
|
|
if ((USE_PROM_CMDLINE && arcs_cmdline[0]) ||
|
|
(USE_DTB_CMDLINE && !boot_command_line[0]))
|
|
strlcpy(boot_command_line, arcs_cmdline, COMMAND_LINE_SIZE);
|
|
|
|
if (EXTEND_WITH_PROM && arcs_cmdline[0]) {
|
|
if (boot_command_line[0])
|
|
strlcat(boot_command_line, " ", COMMAND_LINE_SIZE);
|
|
strlcat(boot_command_line, arcs_cmdline, COMMAND_LINE_SIZE);
|
|
}
|
|
|
|
#if defined(CONFIG_CMDLINE_BOOL)
|
|
if (builtin_cmdline[0]) {
|
|
if (boot_command_line[0])
|
|
strlcat(boot_command_line, " ", COMMAND_LINE_SIZE);
|
|
strlcat(boot_command_line, builtin_cmdline, COMMAND_LINE_SIZE);
|
|
}
|
|
|
|
if (BUILTIN_EXTEND_WITH_PROM && arcs_cmdline[0]) {
|
|
if (boot_command_line[0])
|
|
strlcat(boot_command_line, " ", COMMAND_LINE_SIZE);
|
|
strlcat(boot_command_line, arcs_cmdline, COMMAND_LINE_SIZE);
|
|
}
|
|
#endif
|
|
#endif
|
|
strlcpy(command_line, boot_command_line, COMMAND_LINE_SIZE);
|
|
|
|
*cmdline_p = command_line;
|
|
|
|
parse_early_param();
|
|
|
|
if (usermem)
|
|
pr_info("User-defined physical RAM map overwrite\n");
|
|
|
|
check_kernel_sections_mem();
|
|
|
|
early_init_fdt_reserve_self();
|
|
early_init_fdt_scan_reserved_mem();
|
|
|
|
#ifndef CONFIG_NUMA
|
|
memblock_set_node(0, PHYS_ADDR_MAX, &memblock.memory, 0);
|
|
#endif
|
|
bootmem_init();
|
|
|
|
/*
|
|
* Prevent memblock from allocating high memory.
|
|
* This cannot be done before max_low_pfn is detected, so up
|
|
* to this point is possible to only reserve physical memory
|
|
* with memblock_reserve; memblock_alloc* can be used
|
|
* only after this point
|
|
*/
|
|
memblock_set_current_limit(PFN_PHYS(max_low_pfn));
|
|
|
|
#ifdef CONFIG_PROC_VMCORE
|
|
if (setup_elfcorehdr && setup_elfcorehdr_size) {
|
|
printk(KERN_INFO "kdump reserved memory at %lx-%lx\n",
|
|
setup_elfcorehdr, setup_elfcorehdr_size);
|
|
memblock_reserve(setup_elfcorehdr, setup_elfcorehdr_size);
|
|
}
|
|
#endif
|
|
|
|
mips_parse_crashkernel();
|
|
#ifdef CONFIG_KEXEC
|
|
if (crashk_res.start != crashk_res.end)
|
|
memblock_reserve(crashk_res.start,
|
|
crashk_res.end - crashk_res.start + 1);
|
|
#endif
|
|
device_tree_init();
|
|
|
|
/*
|
|
* In order to reduce the possibility of kernel panic when failed to
|
|
* get IO TLB memory under CONFIG_SWIOTLB, it is better to allocate
|
|
* low memory as small as possible before plat_swiotlb_setup(), so
|
|
* make sparse_init() using top-down allocation.
|
|
*/
|
|
memblock_set_bottom_up(false);
|
|
sparse_init();
|
|
memblock_set_bottom_up(true);
|
|
|
|
plat_swiotlb_setup();
|
|
|
|
dma_contiguous_reserve(PFN_PHYS(max_low_pfn));
|
|
|
|
/* Reserve for hibernation. */
|
|
memblock_reserve(__pa_symbol(&__nosave_begin),
|
|
__pa_symbol(&__nosave_end) - __pa_symbol(&__nosave_begin));
|
|
|
|
fdt_init_reserved_mem();
|
|
|
|
memblock_dump_all();
|
|
|
|
early_memtest(PFN_PHYS(ARCH_PFN_OFFSET), PFN_PHYS(max_low_pfn));
|
|
}
|
|
|
|
static void __init resource_init(void)
|
|
{
|
|
struct memblock_region *region;
|
|
|
|
if (UNCAC_BASE != IO_BASE)
|
|
return;
|
|
|
|
code_resource.start = __pa_symbol(&_text);
|
|
code_resource.end = __pa_symbol(&_etext) - 1;
|
|
data_resource.start = __pa_symbol(&_etext);
|
|
data_resource.end = __pa_symbol(&_edata) - 1;
|
|
bss_resource.start = __pa_symbol(&__bss_start);
|
|
bss_resource.end = __pa_symbol(&__bss_stop) - 1;
|
|
|
|
for_each_memblock(memory, region) {
|
|
phys_addr_t start = PFN_PHYS(memblock_region_memory_base_pfn(region));
|
|
phys_addr_t end = PFN_PHYS(memblock_region_memory_end_pfn(region)) - 1;
|
|
struct resource *res;
|
|
|
|
res = memblock_alloc(sizeof(struct resource), SMP_CACHE_BYTES);
|
|
if (!res)
|
|
panic("%s: Failed to allocate %zu bytes\n", __func__,
|
|
sizeof(struct resource));
|
|
|
|
res->start = start;
|
|
res->end = end;
|
|
res->flags = IORESOURCE_SYSTEM_RAM | IORESOURCE_BUSY;
|
|
res->name = "System RAM";
|
|
|
|
request_resource(&iomem_resource, res);
|
|
|
|
/*
|
|
* We don't know which RAM region contains kernel data,
|
|
* so we try it repeatedly and let the resource manager
|
|
* test it.
|
|
*/
|
|
request_resource(res, &code_resource);
|
|
request_resource(res, &data_resource);
|
|
request_resource(res, &bss_resource);
|
|
request_crashkernel(res);
|
|
}
|
|
}
|
|
|
|
#ifdef CONFIG_SMP
|
|
static void __init prefill_possible_map(void)
|
|
{
|
|
int i, possible = num_possible_cpus();
|
|
|
|
if (possible > nr_cpu_ids)
|
|
possible = nr_cpu_ids;
|
|
|
|
for (i = 0; i < possible; i++)
|
|
set_cpu_possible(i, true);
|
|
for (; i < NR_CPUS; i++)
|
|
set_cpu_possible(i, false);
|
|
|
|
nr_cpu_ids = possible;
|
|
}
|
|
#else
|
|
static inline void prefill_possible_map(void) {}
|
|
#endif
|
|
|
|
void __init setup_arch(char **cmdline_p)
|
|
{
|
|
cpu_probe();
|
|
mips_cm_probe();
|
|
prom_init();
|
|
|
|
setup_early_fdc_console();
|
|
#ifdef CONFIG_EARLY_PRINTK
|
|
setup_early_printk();
|
|
#endif
|
|
cpu_report();
|
|
check_bugs_early();
|
|
|
|
#if defined(CONFIG_VT)
|
|
#if defined(CONFIG_VGA_CONSOLE)
|
|
conswitchp = &vga_con;
|
|
#elif defined(CONFIG_DUMMY_CONSOLE)
|
|
conswitchp = &dummy_con;
|
|
#endif
|
|
#endif
|
|
|
|
arch_mem_init(cmdline_p);
|
|
|
|
resource_init();
|
|
plat_smp_setup();
|
|
prefill_possible_map();
|
|
|
|
cpu_cache_init();
|
|
paging_init();
|
|
}
|
|
|
|
unsigned long kernelsp[NR_CPUS];
|
|
unsigned long fw_arg0, fw_arg1, fw_arg2, fw_arg3;
|
|
|
|
#ifdef CONFIG_USE_OF
|
|
unsigned long fw_passed_dtb;
|
|
#endif
|
|
|
|
#ifdef CONFIG_DEBUG_FS
|
|
struct dentry *mips_debugfs_dir;
|
|
static int __init debugfs_mips(void)
|
|
{
|
|
mips_debugfs_dir = debugfs_create_dir("mips", NULL);
|
|
return 0;
|
|
}
|
|
arch_initcall(debugfs_mips);
|
|
#endif
|
|
|
|
#ifdef CONFIG_DMA_MAYBE_COHERENT
|
|
/* User defined DMA coherency from command line. */
|
|
enum coherent_io_user_state coherentio = IO_COHERENCE_DEFAULT;
|
|
EXPORT_SYMBOL_GPL(coherentio);
|
|
int hw_coherentio = 0; /* Actual hardware supported DMA coherency setting. */
|
|
|
|
static int __init setcoherentio(char *str)
|
|
{
|
|
coherentio = IO_COHERENCE_ENABLED;
|
|
pr_info("Hardware DMA cache coherency (command line)\n");
|
|
return 0;
|
|
}
|
|
early_param("coherentio", setcoherentio);
|
|
|
|
static int __init setnocoherentio(char *str)
|
|
{
|
|
coherentio = IO_COHERENCE_DISABLED;
|
|
pr_info("Software DMA cache coherency (command line)\n");
|
|
return 0;
|
|
}
|
|
early_param("nocoherentio", setnocoherentio);
|
|
#endif
|
|
|
|
void __init arch_cpu_finalize_init(void)
|
|
{
|
|
unsigned int cpu = smp_processor_id();
|
|
|
|
cpu_data[cpu].udelay_val = loops_per_jiffy;
|
|
check_bugs32();
|
|
|
|
if (IS_ENABLED(CONFIG_CPU_R4X00_BUGS64))
|
|
check_bugs64();
|
|
}
|