android_kernel_xiaomi_sm8350/drivers/hwmon/ads7871.c
Thomas Gleixner aec89d292c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 51
Based on 1 normalized pattern(s):

  this program is distributed in the hope that it will be useful but
  without any warranty without even the implied warranty of
  merchantability or fitness for a particular purpose see the gnu
  general public license for more details this program is free
  software you can redistribute it and or modify it under the terms of
  the gnu general public license version 2 or later as publishhed by
  the free software foundation

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071857.852833887@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-24 17:36:42 +02:00

208 lines
5.5 KiB
C

// SPDX-License-Identifier: GPL-2.0-or-later
/*
* ads7871 - driver for TI ADS7871 A/D converter
*
* Copyright (c) 2010 Paul Thomas <pthomas8589@gmail.com>
*
* You need to have something like this in struct spi_board_info
* {
* .modalias = "ads7871",
* .max_speed_hz = 2*1000*1000,
* .chip_select = 0,
* .bus_num = 1,
* },
*/
/*From figure 18 in the datasheet*/
/*Register addresses*/
#define REG_LS_BYTE 0 /*A/D Output Data, LS Byte*/
#define REG_MS_BYTE 1 /*A/D Output Data, MS Byte*/
#define REG_PGA_VALID 2 /*PGA Valid Register*/
#define REG_AD_CONTROL 3 /*A/D Control Register*/
#define REG_GAIN_MUX 4 /*Gain/Mux Register*/
#define REG_IO_STATE 5 /*Digital I/O State Register*/
#define REG_IO_CONTROL 6 /*Digital I/O Control Register*/
#define REG_OSC_CONTROL 7 /*Rev/Oscillator Control Register*/
#define REG_SER_CONTROL 24 /*Serial Interface Control Register*/
#define REG_ID 31 /*ID Register*/
/*
* From figure 17 in the datasheet
* These bits get ORed with the address to form
* the instruction byte
*/
/*Instruction Bit masks*/
#define INST_MODE_BM (1 << 7)
#define INST_READ_BM (1 << 6)
#define INST_16BIT_BM (1 << 5)
/*From figure 18 in the datasheet*/
/*bit masks for Rev/Oscillator Control Register*/
#define MUX_CNV_BV 7
#define MUX_CNV_BM (1 << MUX_CNV_BV)
#define MUX_M3_BM (1 << 3) /*M3 selects single ended*/
#define MUX_G_BV 4 /*allows for reg = (gain << MUX_G_BV) | ...*/
/*From figure 18 in the datasheet*/
/*bit masks for Rev/Oscillator Control Register*/
#define OSC_OSCR_BM (1 << 5)
#define OSC_OSCE_BM (1 << 4)
#define OSC_REFE_BM (1 << 3)
#define OSC_BUFE_BM (1 << 2)
#define OSC_R2V_BM (1 << 1)
#define OSC_RBG_BM (1 << 0)
#include <linux/module.h>
#include <linux/init.h>
#include <linux/spi/spi.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/delay.h>
#define DEVICE_NAME "ads7871"
struct ads7871_data {
struct spi_device *spi;
};
static int ads7871_read_reg8(struct spi_device *spi, int reg)
{
int ret;
reg = reg | INST_READ_BM;
ret = spi_w8r8(spi, reg);
return ret;
}
static int ads7871_read_reg16(struct spi_device *spi, int reg)
{
int ret;
reg = reg | INST_READ_BM | INST_16BIT_BM;
ret = spi_w8r16(spi, reg);
return ret;
}
static int ads7871_write_reg8(struct spi_device *spi, int reg, u8 val)
{
u8 tmp[2] = {reg, val};
return spi_write(spi, tmp, sizeof(tmp));
}
static ssize_t voltage_show(struct device *dev, struct device_attribute *da,
char *buf)
{
struct ads7871_data *pdata = dev_get_drvdata(dev);
struct spi_device *spi = pdata->spi;
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int ret, val, i = 0;
uint8_t channel, mux_cnv;
channel = attr->index;
/*
* TODO: add support for conversions
* other than single ended with a gain of 1
*/
/*MUX_M3_BM forces single ended*/
/*This is also where the gain of the PGA would be set*/
ads7871_write_reg8(spi, REG_GAIN_MUX,
(MUX_CNV_BM | MUX_M3_BM | channel));
ret = ads7871_read_reg8(spi, REG_GAIN_MUX);
mux_cnv = ((ret & MUX_CNV_BM) >> MUX_CNV_BV);
/*
* on 400MHz arm9 platform the conversion
* is already done when we do this test
*/
while ((i < 2) && mux_cnv) {
i++;
ret = ads7871_read_reg8(spi, REG_GAIN_MUX);
mux_cnv = ((ret & MUX_CNV_BM) >> MUX_CNV_BV);
msleep_interruptible(1);
}
if (mux_cnv == 0) {
val = ads7871_read_reg16(spi, REG_LS_BYTE);
/*result in volts*10000 = (val/8192)*2.5*10000*/
val = ((val >> 2) * 25000) / 8192;
return sprintf(buf, "%d\n", val);
} else {
return -1;
}
}
static SENSOR_DEVICE_ATTR_RO(in0_input, voltage, 0);
static SENSOR_DEVICE_ATTR_RO(in1_input, voltage, 1);
static SENSOR_DEVICE_ATTR_RO(in2_input, voltage, 2);
static SENSOR_DEVICE_ATTR_RO(in3_input, voltage, 3);
static SENSOR_DEVICE_ATTR_RO(in4_input, voltage, 4);
static SENSOR_DEVICE_ATTR_RO(in5_input, voltage, 5);
static SENSOR_DEVICE_ATTR_RO(in6_input, voltage, 6);
static SENSOR_DEVICE_ATTR_RO(in7_input, voltage, 7);
static struct attribute *ads7871_attrs[] = {
&sensor_dev_attr_in0_input.dev_attr.attr,
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in2_input.dev_attr.attr,
&sensor_dev_attr_in3_input.dev_attr.attr,
&sensor_dev_attr_in4_input.dev_attr.attr,
&sensor_dev_attr_in5_input.dev_attr.attr,
&sensor_dev_attr_in6_input.dev_attr.attr,
&sensor_dev_attr_in7_input.dev_attr.attr,
NULL
};
ATTRIBUTE_GROUPS(ads7871);
static int ads7871_probe(struct spi_device *spi)
{
struct device *dev = &spi->dev;
int ret;
uint8_t val;
struct ads7871_data *pdata;
struct device *hwmon_dev;
/* Configure the SPI bus */
spi->mode = (SPI_MODE_0);
spi->bits_per_word = 8;
spi_setup(spi);
ads7871_write_reg8(spi, REG_SER_CONTROL, 0);
ads7871_write_reg8(spi, REG_AD_CONTROL, 0);
val = (OSC_OSCR_BM | OSC_OSCE_BM | OSC_REFE_BM | OSC_BUFE_BM);
ads7871_write_reg8(spi, REG_OSC_CONTROL, val);
ret = ads7871_read_reg8(spi, REG_OSC_CONTROL);
dev_dbg(dev, "REG_OSC_CONTROL write:%x, read:%x\n", val, ret);
/*
* because there is no other error checking on an SPI bus
* we need to make sure we really have a chip
*/
if (val != ret)
return -ENODEV;
pdata = devm_kzalloc(dev, sizeof(struct ads7871_data), GFP_KERNEL);
if (!pdata)
return -ENOMEM;
pdata->spi = spi;
hwmon_dev = devm_hwmon_device_register_with_groups(dev, spi->modalias,
pdata,
ads7871_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static struct spi_driver ads7871_driver = {
.driver = {
.name = DEVICE_NAME,
},
.probe = ads7871_probe,
};
module_spi_driver(ads7871_driver);
MODULE_AUTHOR("Paul Thomas <pthomas8589@gmail.com>");
MODULE_DESCRIPTION("TI ADS7871 A/D driver");
MODULE_LICENSE("GPL");