3a9e3a51dd
Set bits 0, 4, 5 and 7 of PCI configuration register 0x40 in the quirk. This has the following effects and is recommended by the vendor. * Force enable of IDE channels (used to be left alone as BIOS configured) * Change initial phase behavior of PIO cycle such that the host pulls down the bus instead of tristating it. Vendor recommends this setting. The above settings are better for the current generation of controllers and needed for the upcoming next generation. Tested on JMB363. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Ethan Hsiao <ethanhsiao@jmicron.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
1709 lines
61 KiB
C
1709 lines
61 KiB
C
/*
|
|
* This file contains work-arounds for many known PCI hardware
|
|
* bugs. Devices present only on certain architectures (host
|
|
* bridges et cetera) should be handled in arch-specific code.
|
|
*
|
|
* Note: any quirks for hotpluggable devices must _NOT_ be declared __init.
|
|
*
|
|
* Copyright (c) 1999 Martin Mares <mj@ucw.cz>
|
|
*
|
|
* Init/reset quirks for USB host controllers should be in the
|
|
* USB quirks file, where their drivers can access reuse it.
|
|
*
|
|
* The bridge optimization stuff has been removed. If you really
|
|
* have a silly BIOS which is unable to set your host bridge right,
|
|
* use the PowerTweak utility (see http://powertweak.sourceforge.net).
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/init.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/acpi.h>
|
|
#include "pci.h"
|
|
|
|
/* The Mellanox Tavor device gives false positive parity errors
|
|
* Mark this device with a broken_parity_status, to allow
|
|
* PCI scanning code to "skip" this now blacklisted device.
|
|
*/
|
|
static void __devinit quirk_mellanox_tavor(struct pci_dev *dev)
|
|
{
|
|
dev->broken_parity_status = 1; /* This device gives false positives */
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX,PCI_DEVICE_ID_MELLANOX_TAVOR,quirk_mellanox_tavor);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX,PCI_DEVICE_ID_MELLANOX_TAVOR_BRIDGE,quirk_mellanox_tavor);
|
|
|
|
/* Deal with broken BIOS'es that neglect to enable passive release,
|
|
which can cause problems in combination with the 82441FX/PPro MTRRs */
|
|
static void quirk_passive_release(struct pci_dev *dev)
|
|
{
|
|
struct pci_dev *d = NULL;
|
|
unsigned char dlc;
|
|
|
|
/* We have to make sure a particular bit is set in the PIIX3
|
|
ISA bridge, so we have to go out and find it. */
|
|
while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) {
|
|
pci_read_config_byte(d, 0x82, &dlc);
|
|
if (!(dlc & 1<<1)) {
|
|
printk(KERN_ERR "PCI: PIIX3: Enabling Passive Release on %s\n", pci_name(d));
|
|
dlc |= 1<<1;
|
|
pci_write_config_byte(d, 0x82, dlc);
|
|
}
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release );
|
|
|
|
/* The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround
|
|
but VIA don't answer queries. If you happen to have good contacts at VIA
|
|
ask them for me please -- Alan
|
|
|
|
This appears to be BIOS not version dependent. So presumably there is a
|
|
chipset level fix */
|
|
int isa_dma_bridge_buggy;
|
|
EXPORT_SYMBOL(isa_dma_bridge_buggy);
|
|
|
|
static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev)
|
|
{
|
|
if (!isa_dma_bridge_buggy) {
|
|
isa_dma_bridge_buggy=1;
|
|
printk(KERN_INFO "Activating ISA DMA hang workarounds.\n");
|
|
}
|
|
}
|
|
/*
|
|
* Its not totally clear which chipsets are the problematic ones
|
|
* We know 82C586 and 82C596 variants are affected.
|
|
*/
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs );
|
|
|
|
int pci_pci_problems;
|
|
EXPORT_SYMBOL(pci_pci_problems);
|
|
|
|
/*
|
|
* Chipsets where PCI->PCI transfers vanish or hang
|
|
*/
|
|
static void __devinit quirk_nopcipci(struct pci_dev *dev)
|
|
{
|
|
if ((pci_pci_problems & PCIPCI_FAIL)==0) {
|
|
printk(KERN_INFO "Disabling direct PCI/PCI transfers.\n");
|
|
pci_pci_problems |= PCIPCI_FAIL;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci );
|
|
|
|
static void __devinit quirk_nopciamd(struct pci_dev *dev)
|
|
{
|
|
u8 rev;
|
|
pci_read_config_byte(dev, 0x08, &rev);
|
|
if (rev == 0x13) {
|
|
/* Erratum 24 */
|
|
printk(KERN_INFO "Chipset erratum: Disabling direct PCI/AGP transfers.\n");
|
|
pci_pci_problems |= PCIAGP_FAIL;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8151_0, quirk_nopciamd );
|
|
|
|
/*
|
|
* Triton requires workarounds to be used by the drivers
|
|
*/
|
|
static void __devinit quirk_triton(struct pci_dev *dev)
|
|
{
|
|
if ((pci_pci_problems&PCIPCI_TRITON)==0) {
|
|
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
|
|
pci_pci_problems |= PCIPCI_TRITON;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton );
|
|
|
|
/*
|
|
* VIA Apollo KT133 needs PCI latency patch
|
|
* Made according to a windows driver based patch by George E. Breese
|
|
* see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm
|
|
* Also see http://www.au-ja.org/review-kt133a-1-en.phtml for
|
|
* the info on which Mr Breese based his work.
|
|
*
|
|
* Updated based on further information from the site and also on
|
|
* information provided by VIA
|
|
*/
|
|
static void quirk_vialatency(struct pci_dev *dev)
|
|
{
|
|
struct pci_dev *p;
|
|
u8 rev;
|
|
u8 busarb;
|
|
/* Ok we have a potential problem chipset here. Now see if we have
|
|
a buggy southbridge */
|
|
|
|
p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL);
|
|
if (p!=NULL) {
|
|
pci_read_config_byte(p, PCI_CLASS_REVISION, &rev);
|
|
/* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */
|
|
/* Check for buggy part revisions */
|
|
if (rev < 0x40 || rev > 0x42)
|
|
goto exit;
|
|
} else {
|
|
p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL);
|
|
if (p==NULL) /* No problem parts */
|
|
goto exit;
|
|
pci_read_config_byte(p, PCI_CLASS_REVISION, &rev);
|
|
/* Check for buggy part revisions */
|
|
if (rev < 0x10 || rev > 0x12)
|
|
goto exit;
|
|
}
|
|
|
|
/*
|
|
* Ok we have the problem. Now set the PCI master grant to
|
|
* occur every master grant. The apparent bug is that under high
|
|
* PCI load (quite common in Linux of course) you can get data
|
|
* loss when the CPU is held off the bus for 3 bus master requests
|
|
* This happens to include the IDE controllers....
|
|
*
|
|
* VIA only apply this fix when an SB Live! is present but under
|
|
* both Linux and Windows this isnt enough, and we have seen
|
|
* corruption without SB Live! but with things like 3 UDMA IDE
|
|
* controllers. So we ignore that bit of the VIA recommendation..
|
|
*/
|
|
|
|
pci_read_config_byte(dev, 0x76, &busarb);
|
|
/* Set bit 4 and bi 5 of byte 76 to 0x01
|
|
"Master priority rotation on every PCI master grant */
|
|
busarb &= ~(1<<5);
|
|
busarb |= (1<<4);
|
|
pci_write_config_byte(dev, 0x76, busarb);
|
|
printk(KERN_INFO "Applying VIA southbridge workaround.\n");
|
|
exit:
|
|
pci_dev_put(p);
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency );
|
|
/* Must restore this on a resume from RAM */
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency );
|
|
|
|
/*
|
|
* VIA Apollo VP3 needs ETBF on BT848/878
|
|
*/
|
|
static void __devinit quirk_viaetbf(struct pci_dev *dev)
|
|
{
|
|
if ((pci_pci_problems&PCIPCI_VIAETBF)==0) {
|
|
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
|
|
pci_pci_problems |= PCIPCI_VIAETBF;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf );
|
|
|
|
static void __devinit quirk_vsfx(struct pci_dev *dev)
|
|
{
|
|
if ((pci_pci_problems&PCIPCI_VSFX)==0) {
|
|
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
|
|
pci_pci_problems |= PCIPCI_VSFX;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx );
|
|
|
|
/*
|
|
* Ali Magik requires workarounds to be used by the drivers
|
|
* that DMA to AGP space. Latency must be set to 0xA and triton
|
|
* workaround applied too
|
|
* [Info kindly provided by ALi]
|
|
*/
|
|
static void __init quirk_alimagik(struct pci_dev *dev)
|
|
{
|
|
if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) {
|
|
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
|
|
pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik );
|
|
|
|
/*
|
|
* Natoma has some interesting boundary conditions with Zoran stuff
|
|
* at least
|
|
*/
|
|
static void __devinit quirk_natoma(struct pci_dev *dev)
|
|
{
|
|
if ((pci_pci_problems&PCIPCI_NATOMA)==0) {
|
|
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
|
|
pci_pci_problems |= PCIPCI_NATOMA;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma );
|
|
|
|
/*
|
|
* This chip can cause PCI parity errors if config register 0xA0 is read
|
|
* while DMAs are occurring.
|
|
*/
|
|
static void __devinit quirk_citrine(struct pci_dev *dev)
|
|
{
|
|
dev->cfg_size = 0xA0;
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine );
|
|
|
|
/*
|
|
* S3 868 and 968 chips report region size equal to 32M, but they decode 64M.
|
|
* If it's needed, re-allocate the region.
|
|
*/
|
|
static void __devinit quirk_s3_64M(struct pci_dev *dev)
|
|
{
|
|
struct resource *r = &dev->resource[0];
|
|
|
|
if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) {
|
|
r->start = 0;
|
|
r->end = 0x3ffffff;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M );
|
|
|
|
static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region,
|
|
unsigned size, int nr, const char *name)
|
|
{
|
|
region &= ~(size-1);
|
|
if (region) {
|
|
struct pci_bus_region bus_region;
|
|
struct resource *res = dev->resource + nr;
|
|
|
|
res->name = pci_name(dev);
|
|
res->start = region;
|
|
res->end = region + size - 1;
|
|
res->flags = IORESOURCE_IO;
|
|
|
|
/* Convert from PCI bus to resource space. */
|
|
bus_region.start = res->start;
|
|
bus_region.end = res->end;
|
|
pcibios_bus_to_resource(dev, res, &bus_region);
|
|
|
|
pci_claim_resource(dev, nr);
|
|
printk("PCI quirk: region %04x-%04x claimed by %s\n", region, region + size - 1, name);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* ATI Northbridge setups MCE the processor if you even
|
|
* read somewhere between 0x3b0->0x3bb or read 0x3d3
|
|
*/
|
|
static void __devinit quirk_ati_exploding_mce(struct pci_dev *dev)
|
|
{
|
|
printk(KERN_INFO "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.\n");
|
|
/* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */
|
|
request_region(0x3b0, 0x0C, "RadeonIGP");
|
|
request_region(0x3d3, 0x01, "RadeonIGP");
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce );
|
|
|
|
/*
|
|
* Let's make the southbridge information explicit instead
|
|
* of having to worry about people probing the ACPI areas,
|
|
* for example.. (Yes, it happens, and if you read the wrong
|
|
* ACPI register it will put the machine to sleep with no
|
|
* way of waking it up again. Bummer).
|
|
*
|
|
* ALI M7101: Two IO regions pointed to by words at
|
|
* 0xE0 (64 bytes of ACPI registers)
|
|
* 0xE2 (32 bytes of SMB registers)
|
|
*/
|
|
static void __devinit quirk_ali7101_acpi(struct pci_dev *dev)
|
|
{
|
|
u16 region;
|
|
|
|
pci_read_config_word(dev, 0xE0, ®ion);
|
|
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "ali7101 ACPI");
|
|
pci_read_config_word(dev, 0xE2, ®ion);
|
|
quirk_io_region(dev, region, 32, PCI_BRIDGE_RESOURCES+1, "ali7101 SMB");
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi );
|
|
|
|
static void piix4_io_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable)
|
|
{
|
|
u32 devres;
|
|
u32 mask, size, base;
|
|
|
|
pci_read_config_dword(dev, port, &devres);
|
|
if ((devres & enable) != enable)
|
|
return;
|
|
mask = (devres >> 16) & 15;
|
|
base = devres & 0xffff;
|
|
size = 16;
|
|
for (;;) {
|
|
unsigned bit = size >> 1;
|
|
if ((bit & mask) == bit)
|
|
break;
|
|
size = bit;
|
|
}
|
|
/*
|
|
* For now we only print it out. Eventually we'll want to
|
|
* reserve it (at least if it's in the 0x1000+ range), but
|
|
* let's get enough confirmation reports first.
|
|
*/
|
|
base &= -size;
|
|
printk("%s PIO at %04x-%04x\n", name, base, base + size - 1);
|
|
}
|
|
|
|
static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable)
|
|
{
|
|
u32 devres;
|
|
u32 mask, size, base;
|
|
|
|
pci_read_config_dword(dev, port, &devres);
|
|
if ((devres & enable) != enable)
|
|
return;
|
|
base = devres & 0xffff0000;
|
|
mask = (devres & 0x3f) << 16;
|
|
size = 128 << 16;
|
|
for (;;) {
|
|
unsigned bit = size >> 1;
|
|
if ((bit & mask) == bit)
|
|
break;
|
|
size = bit;
|
|
}
|
|
/*
|
|
* For now we only print it out. Eventually we'll want to
|
|
* reserve it, but let's get enough confirmation reports first.
|
|
*/
|
|
base &= -size;
|
|
printk("%s MMIO at %04x-%04x\n", name, base, base + size - 1);
|
|
}
|
|
|
|
/*
|
|
* PIIX4 ACPI: Two IO regions pointed to by longwords at
|
|
* 0x40 (64 bytes of ACPI registers)
|
|
* 0x90 (16 bytes of SMB registers)
|
|
* and a few strange programmable PIIX4 device resources.
|
|
*/
|
|
static void __devinit quirk_piix4_acpi(struct pci_dev *dev)
|
|
{
|
|
u32 region, res_a;
|
|
|
|
pci_read_config_dword(dev, 0x40, ®ion);
|
|
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI");
|
|
pci_read_config_dword(dev, 0x90, ®ion);
|
|
quirk_io_region(dev, region, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB");
|
|
|
|
/* Device resource A has enables for some of the other ones */
|
|
pci_read_config_dword(dev, 0x5c, &res_a);
|
|
|
|
piix4_io_quirk(dev, "PIIX4 devres B", 0x60, 3 << 21);
|
|
piix4_io_quirk(dev, "PIIX4 devres C", 0x64, 3 << 21);
|
|
|
|
/* Device resource D is just bitfields for static resources */
|
|
|
|
/* Device 12 enabled? */
|
|
if (res_a & (1 << 29)) {
|
|
piix4_io_quirk(dev, "PIIX4 devres E", 0x68, 1 << 20);
|
|
piix4_mem_quirk(dev, "PIIX4 devres F", 0x6c, 1 << 7);
|
|
}
|
|
/* Device 13 enabled? */
|
|
if (res_a & (1 << 30)) {
|
|
piix4_io_quirk(dev, "PIIX4 devres G", 0x70, 1 << 20);
|
|
piix4_mem_quirk(dev, "PIIX4 devres H", 0x74, 1 << 7);
|
|
}
|
|
piix4_io_quirk(dev, "PIIX4 devres I", 0x78, 1 << 20);
|
|
piix4_io_quirk(dev, "PIIX4 devres J", 0x7c, 1 << 20);
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_3, quirk_piix4_acpi );
|
|
|
|
/*
|
|
* ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at
|
|
* 0x40 (128 bytes of ACPI, GPIO & TCO registers)
|
|
* 0x58 (64 bytes of GPIO I/O space)
|
|
*/
|
|
static void __devinit quirk_ich4_lpc_acpi(struct pci_dev *dev)
|
|
{
|
|
u32 region;
|
|
|
|
pci_read_config_dword(dev, 0x40, ®ion);
|
|
quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH4 ACPI/GPIO/TCO");
|
|
|
|
pci_read_config_dword(dev, 0x58, ®ion);
|
|
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH4 GPIO");
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi );
|
|
|
|
static void __devinit quirk_ich6_lpc_acpi(struct pci_dev *dev)
|
|
{
|
|
u32 region;
|
|
|
|
pci_read_config_dword(dev, 0x40, ®ion);
|
|
quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH6 ACPI/GPIO/TCO");
|
|
|
|
pci_read_config_dword(dev, 0x48, ®ion);
|
|
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH6 GPIO");
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich6_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich6_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich6_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich6_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich6_lpc_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich6_lpc_acpi );
|
|
|
|
/*
|
|
* VIA ACPI: One IO region pointed to by longword at
|
|
* 0x48 or 0x20 (256 bytes of ACPI registers)
|
|
*/
|
|
static void __devinit quirk_vt82c586_acpi(struct pci_dev *dev)
|
|
{
|
|
u32 region;
|
|
|
|
if (dev->revision & 0x10) {
|
|
pci_read_config_dword(dev, 0x48, ®ion);
|
|
region &= PCI_BASE_ADDRESS_IO_MASK;
|
|
quirk_io_region(dev, region, 256, PCI_BRIDGE_RESOURCES, "vt82c586 ACPI");
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi );
|
|
|
|
/*
|
|
* VIA VT82C686 ACPI: Three IO region pointed to by (long)words at
|
|
* 0x48 (256 bytes of ACPI registers)
|
|
* 0x70 (128 bytes of hardware monitoring register)
|
|
* 0x90 (16 bytes of SMB registers)
|
|
*/
|
|
static void __devinit quirk_vt82c686_acpi(struct pci_dev *dev)
|
|
{
|
|
u16 hm;
|
|
u32 smb;
|
|
|
|
quirk_vt82c586_acpi(dev);
|
|
|
|
pci_read_config_word(dev, 0x70, &hm);
|
|
hm &= PCI_BASE_ADDRESS_IO_MASK;
|
|
quirk_io_region(dev, hm, 128, PCI_BRIDGE_RESOURCES + 1, "vt82c686 HW-mon");
|
|
|
|
pci_read_config_dword(dev, 0x90, &smb);
|
|
smb &= PCI_BASE_ADDRESS_IO_MASK;
|
|
quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 2, "vt82c686 SMB");
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi );
|
|
|
|
/*
|
|
* VIA VT8235 ISA Bridge: Two IO regions pointed to by words at
|
|
* 0x88 (128 bytes of power management registers)
|
|
* 0xd0 (16 bytes of SMB registers)
|
|
*/
|
|
static void __devinit quirk_vt8235_acpi(struct pci_dev *dev)
|
|
{
|
|
u16 pm, smb;
|
|
|
|
pci_read_config_word(dev, 0x88, &pm);
|
|
pm &= PCI_BASE_ADDRESS_IO_MASK;
|
|
quirk_io_region(dev, pm, 128, PCI_BRIDGE_RESOURCES, "vt8235 PM");
|
|
|
|
pci_read_config_word(dev, 0xd0, &smb);
|
|
smb &= PCI_BASE_ADDRESS_IO_MASK;
|
|
quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 1, "vt8235 SMB");
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi);
|
|
|
|
|
|
#ifdef CONFIG_X86_IO_APIC
|
|
|
|
#include <asm/io_apic.h>
|
|
|
|
/*
|
|
* VIA 686A/B: If an IO-APIC is active, we need to route all on-chip
|
|
* devices to the external APIC.
|
|
*
|
|
* TODO: When we have device-specific interrupt routers,
|
|
* this code will go away from quirks.
|
|
*/
|
|
static void quirk_via_ioapic(struct pci_dev *dev)
|
|
{
|
|
u8 tmp;
|
|
|
|
if (nr_ioapics < 1)
|
|
tmp = 0; /* nothing routed to external APIC */
|
|
else
|
|
tmp = 0x1f; /* all known bits (4-0) routed to external APIC */
|
|
|
|
printk(KERN_INFO "PCI: %sbling Via external APIC routing\n",
|
|
tmp == 0 ? "Disa" : "Ena");
|
|
|
|
/* Offset 0x58: External APIC IRQ output control */
|
|
pci_write_config_byte (dev, 0x58, tmp);
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic );
|
|
|
|
/*
|
|
* VIA 8237: Some BIOSs don't set the 'Bypass APIC De-Assert Message' Bit.
|
|
* This leads to doubled level interrupt rates.
|
|
* Set this bit to get rid of cycle wastage.
|
|
* Otherwise uncritical.
|
|
*/
|
|
static void quirk_via_vt8237_bypass_apic_deassert(struct pci_dev *dev)
|
|
{
|
|
u8 misc_control2;
|
|
#define BYPASS_APIC_DEASSERT 8
|
|
|
|
pci_read_config_byte(dev, 0x5B, &misc_control2);
|
|
if (!(misc_control2 & BYPASS_APIC_DEASSERT)) {
|
|
printk(KERN_INFO "PCI: Bypassing VIA 8237 APIC De-Assert Message\n");
|
|
pci_write_config_byte(dev, 0x5B, misc_control2|BYPASS_APIC_DEASSERT);
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert);
|
|
|
|
/*
|
|
* The AMD io apic can hang the box when an apic irq is masked.
|
|
* We check all revs >= B0 (yet not in the pre production!) as the bug
|
|
* is currently marked NoFix
|
|
*
|
|
* We have multiple reports of hangs with this chipset that went away with
|
|
* noapic specified. For the moment we assume it's the erratum. We may be wrong
|
|
* of course. However the advice is demonstrably good even if so..
|
|
*/
|
|
static void __devinit quirk_amd_ioapic(struct pci_dev *dev)
|
|
{
|
|
if (dev->revision >= 0x02) {
|
|
printk(KERN_WARNING "I/O APIC: AMD Erratum #22 may be present. In the event of instability try\n");
|
|
printk(KERN_WARNING " : booting with the \"noapic\" option.\n");
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic );
|
|
|
|
static void __init quirk_ioapic_rmw(struct pci_dev *dev)
|
|
{
|
|
if (dev->devfn == 0 && dev->bus->number == 0)
|
|
sis_apic_bug = 1;
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_ANY_ID, quirk_ioapic_rmw );
|
|
|
|
#define AMD8131_revA0 0x01
|
|
#define AMD8131_revB0 0x11
|
|
#define AMD8131_MISC 0x40
|
|
#define AMD8131_NIOAMODE_BIT 0
|
|
static void quirk_amd_8131_ioapic(struct pci_dev *dev)
|
|
{
|
|
unsigned char tmp;
|
|
|
|
if (nr_ioapics == 0)
|
|
return;
|
|
|
|
if (dev->revision == AMD8131_revA0 || dev->revision == AMD8131_revB0) {
|
|
printk(KERN_INFO "Fixing up AMD8131 IOAPIC mode\n");
|
|
pci_read_config_byte( dev, AMD8131_MISC, &tmp);
|
|
tmp &= ~(1 << AMD8131_NIOAMODE_BIT);
|
|
pci_write_config_byte( dev, AMD8131_MISC, tmp);
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_ioapic);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_ioapic);
|
|
#endif /* CONFIG_X86_IO_APIC */
|
|
|
|
/*
|
|
* Some settings of MMRBC can lead to data corruption so block changes.
|
|
* See AMD 8131 HyperTransport PCI-X Tunnel Revision Guide
|
|
*/
|
|
static void __init quirk_amd_8131_mmrbc(struct pci_dev *dev)
|
|
{
|
|
if (dev->subordinate && dev->revision <= 0x12) {
|
|
printk(KERN_INFO "AMD8131 rev %x detected, disabling PCI-X "
|
|
"MMRBC\n", dev->revision);
|
|
dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MMRBC;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_mmrbc);
|
|
|
|
/*
|
|
* FIXME: it is questionable that quirk_via_acpi
|
|
* is needed. It shows up as an ISA bridge, and does not
|
|
* support the PCI_INTERRUPT_LINE register at all. Therefore
|
|
* it seems like setting the pci_dev's 'irq' to the
|
|
* value of the ACPI SCI interrupt is only done for convenience.
|
|
* -jgarzik
|
|
*/
|
|
static void __devinit quirk_via_acpi(struct pci_dev *d)
|
|
{
|
|
/*
|
|
* VIA ACPI device: SCI IRQ line in PCI config byte 0x42
|
|
*/
|
|
u8 irq;
|
|
pci_read_config_byte(d, 0x42, &irq);
|
|
irq &= 0xf;
|
|
if (irq && (irq != 2))
|
|
d->irq = irq;
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi );
|
|
|
|
|
|
/*
|
|
* VIA bridges which have VLink
|
|
*/
|
|
|
|
static int via_vlink_dev_lo = -1, via_vlink_dev_hi = 18;
|
|
|
|
static void quirk_via_bridge(struct pci_dev *dev)
|
|
{
|
|
/* See what bridge we have and find the device ranges */
|
|
switch (dev->device) {
|
|
case PCI_DEVICE_ID_VIA_82C686:
|
|
/* The VT82C686 is special, it attaches to PCI and can have
|
|
any device number. All its subdevices are functions of
|
|
that single device. */
|
|
via_vlink_dev_lo = PCI_SLOT(dev->devfn);
|
|
via_vlink_dev_hi = PCI_SLOT(dev->devfn);
|
|
break;
|
|
case PCI_DEVICE_ID_VIA_8237:
|
|
case PCI_DEVICE_ID_VIA_8237A:
|
|
via_vlink_dev_lo = 15;
|
|
break;
|
|
case PCI_DEVICE_ID_VIA_8235:
|
|
via_vlink_dev_lo = 16;
|
|
break;
|
|
case PCI_DEVICE_ID_VIA_8231:
|
|
case PCI_DEVICE_ID_VIA_8233_0:
|
|
case PCI_DEVICE_ID_VIA_8233A:
|
|
case PCI_DEVICE_ID_VIA_8233C_0:
|
|
via_vlink_dev_lo = 17;
|
|
break;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_bridge);
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, quirk_via_bridge);
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_0, quirk_via_bridge);
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233A, quirk_via_bridge);
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233C_0, quirk_via_bridge);
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_via_bridge);
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_bridge);
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237A, quirk_via_bridge);
|
|
|
|
/**
|
|
* quirk_via_vlink - VIA VLink IRQ number update
|
|
* @dev: PCI device
|
|
*
|
|
* If the device we are dealing with is on a PIC IRQ we need to
|
|
* ensure that the IRQ line register which usually is not relevant
|
|
* for PCI cards, is actually written so that interrupts get sent
|
|
* to the right place.
|
|
* We only do this on systems where a VIA south bridge was detected,
|
|
* and only for VIA devices on the motherboard (see quirk_via_bridge
|
|
* above).
|
|
*/
|
|
|
|
static void quirk_via_vlink(struct pci_dev *dev)
|
|
{
|
|
u8 irq, new_irq;
|
|
|
|
/* Check if we have VLink at all */
|
|
if (via_vlink_dev_lo == -1)
|
|
return;
|
|
|
|
new_irq = dev->irq;
|
|
|
|
/* Don't quirk interrupts outside the legacy IRQ range */
|
|
if (!new_irq || new_irq > 15)
|
|
return;
|
|
|
|
/* Internal device ? */
|
|
if (dev->bus->number != 0 || PCI_SLOT(dev->devfn) > via_vlink_dev_hi ||
|
|
PCI_SLOT(dev->devfn) < via_vlink_dev_lo)
|
|
return;
|
|
|
|
/* This is an internal VLink device on a PIC interrupt. The BIOS
|
|
ought to have set this but may not have, so we redo it */
|
|
|
|
pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
|
|
if (new_irq != irq) {
|
|
printk(KERN_INFO "PCI: VIA VLink IRQ fixup for %s, from %d to %d\n",
|
|
pci_name(dev), irq, new_irq);
|
|
udelay(15); /* unknown if delay really needed */
|
|
pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq);
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_vlink);
|
|
|
|
/*
|
|
* VIA VT82C598 has its device ID settable and many BIOSes
|
|
* set it to the ID of VT82C597 for backward compatibility.
|
|
* We need to switch it off to be able to recognize the real
|
|
* type of the chip.
|
|
*/
|
|
static void __devinit quirk_vt82c598_id(struct pci_dev *dev)
|
|
{
|
|
pci_write_config_byte(dev, 0xfc, 0);
|
|
pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device);
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id );
|
|
|
|
/*
|
|
* CardBus controllers have a legacy base address that enables them
|
|
* to respond as i82365 pcmcia controllers. We don't want them to
|
|
* do this even if the Linux CardBus driver is not loaded, because
|
|
* the Linux i82365 driver does not (and should not) handle CardBus.
|
|
*/
|
|
static void quirk_cardbus_legacy(struct pci_dev *dev)
|
|
{
|
|
if ((PCI_CLASS_BRIDGE_CARDBUS << 8) ^ dev->class)
|
|
return;
|
|
pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0);
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, quirk_cardbus_legacy);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_ANY_ID, PCI_ANY_ID, quirk_cardbus_legacy);
|
|
|
|
/*
|
|
* Following the PCI ordering rules is optional on the AMD762. I'm not
|
|
* sure what the designers were smoking but let's not inhale...
|
|
*
|
|
* To be fair to AMD, it follows the spec by default, its BIOS people
|
|
* who turn it off!
|
|
*/
|
|
static void quirk_amd_ordering(struct pci_dev *dev)
|
|
{
|
|
u32 pcic;
|
|
pci_read_config_dword(dev, 0x4C, &pcic);
|
|
if ((pcic&6)!=6) {
|
|
pcic |= 6;
|
|
printk(KERN_WARNING "BIOS failed to enable PCI standards compliance, fixing this error.\n");
|
|
pci_write_config_dword(dev, 0x4C, pcic);
|
|
pci_read_config_dword(dev, 0x84, &pcic);
|
|
pcic |= (1<<23); /* Required in this mode */
|
|
pci_write_config_dword(dev, 0x84, pcic);
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering );
|
|
|
|
/*
|
|
* DreamWorks provided workaround for Dunord I-3000 problem
|
|
*
|
|
* This card decodes and responds to addresses not apparently
|
|
* assigned to it. We force a larger allocation to ensure that
|
|
* nothing gets put too close to it.
|
|
*/
|
|
static void __devinit quirk_dunord ( struct pci_dev * dev )
|
|
{
|
|
struct resource *r = &dev->resource [1];
|
|
r->start = 0;
|
|
r->end = 0xffffff;
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord );
|
|
|
|
/*
|
|
* i82380FB mobile docking controller: its PCI-to-PCI bridge
|
|
* is subtractive decoding (transparent), and does indicate this
|
|
* in the ProgIf. Unfortunately, the ProgIf value is wrong - 0x80
|
|
* instead of 0x01.
|
|
*/
|
|
static void __devinit quirk_transparent_bridge(struct pci_dev *dev)
|
|
{
|
|
dev->transparent = 1;
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge );
|
|
|
|
/*
|
|
* Common misconfiguration of the MediaGX/Geode PCI master that will
|
|
* reduce PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1
|
|
* datasheets found at http://www.national.com/ds/GX for info on what
|
|
* these bits do. <christer@weinigel.se>
|
|
*/
|
|
static void quirk_mediagx_master(struct pci_dev *dev)
|
|
{
|
|
u8 reg;
|
|
pci_read_config_byte(dev, 0x41, ®);
|
|
if (reg & 2) {
|
|
reg &= ~2;
|
|
printk(KERN_INFO "PCI: Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", reg);
|
|
pci_write_config_byte(dev, 0x41, reg);
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master );
|
|
|
|
/*
|
|
* Ensure C0 rev restreaming is off. This is normally done by
|
|
* the BIOS but in the odd case it is not the results are corruption
|
|
* hence the presence of a Linux check
|
|
*/
|
|
static void quirk_disable_pxb(struct pci_dev *pdev)
|
|
{
|
|
u16 config;
|
|
|
|
if (pdev->revision != 0x04) /* Only C0 requires this */
|
|
return;
|
|
pci_read_config_word(pdev, 0x40, &config);
|
|
if (config & (1<<6)) {
|
|
config &= ~(1<<6);
|
|
pci_write_config_word(pdev, 0x40, config);
|
|
printk(KERN_INFO "PCI: C0 revision 450NX. Disabling PCI restreaming.\n");
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb );
|
|
|
|
|
|
static void __devinit quirk_sb600_sata(struct pci_dev *pdev)
|
|
{
|
|
/* set sb600 sata to ahci mode */
|
|
if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
|
|
u8 tmp;
|
|
|
|
pci_read_config_byte(pdev, 0x40, &tmp);
|
|
pci_write_config_byte(pdev, 0x40, tmp|1);
|
|
pci_write_config_byte(pdev, 0x9, 1);
|
|
pci_write_config_byte(pdev, 0xa, 6);
|
|
pci_write_config_byte(pdev, 0x40, tmp);
|
|
|
|
pdev->class = PCI_CLASS_STORAGE_SATA_AHCI;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_sb600_sata);
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_sb600_sata);
|
|
|
|
/*
|
|
* Serverworks CSB5 IDE does not fully support native mode
|
|
*/
|
|
static void __devinit quirk_svwks_csb5ide(struct pci_dev *pdev)
|
|
{
|
|
u8 prog;
|
|
pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
|
|
if (prog & 5) {
|
|
prog &= ~5;
|
|
pdev->class &= ~5;
|
|
pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
|
|
/* PCI layer will sort out resources */
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide );
|
|
|
|
/*
|
|
* Intel 82801CAM ICH3-M datasheet says IDE modes must be the same
|
|
*/
|
|
static void __init quirk_ide_samemode(struct pci_dev *pdev)
|
|
{
|
|
u8 prog;
|
|
|
|
pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
|
|
|
|
if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) {
|
|
printk(KERN_INFO "PCI: IDE mode mismatch; forcing legacy mode\n");
|
|
prog &= ~5;
|
|
pdev->class &= ~5;
|
|
pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode);
|
|
|
|
/* This was originally an Alpha specific thing, but it really fits here.
|
|
* The i82375 PCI/EISA bridge appears as non-classified. Fix that.
|
|
*/
|
|
static void __init quirk_eisa_bridge(struct pci_dev *dev)
|
|
{
|
|
dev->class = PCI_CLASS_BRIDGE_EISA << 8;
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge );
|
|
|
|
|
|
/*
|
|
* On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge
|
|
* is not activated. The myth is that Asus said that they do not want the
|
|
* users to be irritated by just another PCI Device in the Win98 device
|
|
* manager. (see the file prog/hotplug/README.p4b in the lm_sensors
|
|
* package 2.7.0 for details)
|
|
*
|
|
* The SMBus PCI Device can be activated by setting a bit in the ICH LPC
|
|
* bridge. Unfortunately, this device has no subvendor/subdevice ID. So it
|
|
* becomes necessary to do this tweak in two steps -- the chosen trigger
|
|
* is either the Host bridge (preferred) or on-board VGA controller.
|
|
*
|
|
* Note that we used to unhide the SMBus that way on Toshiba laptops
|
|
* (Satellite A40 and Tecra M2) but then found that the thermal management
|
|
* was done by SMM code, which could cause unsynchronized concurrent
|
|
* accesses to the SMBus registers, with potentially bad effects. Thus you
|
|
* should be very careful when adding new entries: if SMM is accessing the
|
|
* Intel SMBus, this is a very good reason to leave it hidden.
|
|
*/
|
|
static int asus_hides_smbus;
|
|
|
|
static void __init asus_hides_smbus_hostbridge(struct pci_dev *dev)
|
|
{
|
|
if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) {
|
|
if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB)
|
|
switch(dev->subsystem_device) {
|
|
case 0x8025: /* P4B-LX */
|
|
case 0x8070: /* P4B */
|
|
case 0x8088: /* P4B533 */
|
|
case 0x1626: /* L3C notebook */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB)
|
|
switch(dev->subsystem_device) {
|
|
case 0x80b1: /* P4GE-V */
|
|
case 0x80b2: /* P4PE */
|
|
case 0x8093: /* P4B533-V */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB)
|
|
switch(dev->subsystem_device) {
|
|
case 0x8030: /* P4T533 */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_7205_0)
|
|
switch (dev->subsystem_device) {
|
|
case 0x8070: /* P4G8X Deluxe */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_E7501_MCH)
|
|
switch (dev->subsystem_device) {
|
|
case 0x80c9: /* PU-DLS */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB)
|
|
switch (dev->subsystem_device) {
|
|
case 0x1751: /* M2N notebook */
|
|
case 0x1821: /* M5N notebook */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
|
|
switch (dev->subsystem_device) {
|
|
case 0x184b: /* W1N notebook */
|
|
case 0x186a: /* M6Ne notebook */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB)
|
|
switch (dev->subsystem_device) {
|
|
case 0x80f2: /* P4P800-X */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB)
|
|
switch (dev->subsystem_device) {
|
|
case 0x1882: /* M6V notebook */
|
|
case 0x1977: /* A6VA notebook */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) {
|
|
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
|
|
switch(dev->subsystem_device) {
|
|
case 0x088C: /* HP Compaq nc8000 */
|
|
case 0x0890: /* HP Compaq nc6000 */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB)
|
|
switch (dev->subsystem_device) {
|
|
case 0x12bc: /* HP D330L */
|
|
case 0x12bd: /* HP D530 */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB)
|
|
switch (dev->subsystem_device) {
|
|
case 0x099c: /* HP Compaq nx6110 */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) {
|
|
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
|
|
switch(dev->subsystem_device) {
|
|
case 0xC00C: /* Samsung P35 notebook */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) {
|
|
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
|
|
switch(dev->subsystem_device) {
|
|
case 0x0058: /* Compaq Evo N620c */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
else if (dev->device == PCI_DEVICE_ID_INTEL_82810_IG3)
|
|
switch(dev->subsystem_device) {
|
|
case 0xB16C: /* Compaq Deskpro EP 401963-001 (PCA# 010174) */
|
|
/* Motherboard doesn't have Host bridge
|
|
* subvendor/subdevice IDs, therefore checking
|
|
* its on-board VGA controller */
|
|
asus_hides_smbus = 1;
|
|
}
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7501_MCH, asus_hides_smbus_hostbridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge );
|
|
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3, asus_hides_smbus_hostbridge );
|
|
|
|
static void asus_hides_smbus_lpc(struct pci_dev *dev)
|
|
{
|
|
u16 val;
|
|
|
|
if (likely(!asus_hides_smbus))
|
|
return;
|
|
|
|
pci_read_config_word(dev, 0xF2, &val);
|
|
if (val & 0x8) {
|
|
pci_write_config_word(dev, 0xF2, val & (~0x8));
|
|
pci_read_config_word(dev, 0xF2, &val);
|
|
if (val & 0x8)
|
|
printk(KERN_INFO "PCI: i801 SMBus device continues to play 'hide and seek'! 0x%x\n", val);
|
|
else
|
|
printk(KERN_INFO "PCI: Enabled i801 SMBus device\n");
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc );
|
|
|
|
static void asus_hides_smbus_lpc_ich6(struct pci_dev *dev)
|
|
{
|
|
u32 val, rcba;
|
|
void __iomem *base;
|
|
|
|
if (likely(!asus_hides_smbus))
|
|
return;
|
|
pci_read_config_dword(dev, 0xF0, &rcba);
|
|
base = ioremap_nocache(rcba & 0xFFFFC000, 0x4000); /* use bits 31:14, 16 kB aligned */
|
|
if (base == NULL) return;
|
|
val=readl(base + 0x3418); /* read the Function Disable register, dword mode only */
|
|
writel(val & 0xFFFFFFF7, base + 0x3418); /* enable the SMBus device */
|
|
iounmap(base);
|
|
printk(KERN_INFO "PCI: Enabled ICH6/i801 SMBus device\n");
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6 );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6 );
|
|
|
|
/*
|
|
* SiS 96x south bridge: BIOS typically hides SMBus device...
|
|
*/
|
|
static void quirk_sis_96x_smbus(struct pci_dev *dev)
|
|
{
|
|
u8 val = 0;
|
|
pci_read_config_byte(dev, 0x77, &val);
|
|
if (val & 0x10) {
|
|
printk(KERN_INFO "Enabling SiS 96x SMBus.\n");
|
|
pci_write_config_byte(dev, 0x77, val & ~0x10);
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus );
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus );
|
|
|
|
/*
|
|
* ... This is further complicated by the fact that some SiS96x south
|
|
* bridges pretend to be 85C503/5513 instead. In that case see if we
|
|
* spotted a compatible north bridge to make sure.
|
|
* (pci_find_device doesn't work yet)
|
|
*
|
|
* We can also enable the sis96x bit in the discovery register..
|
|
*/
|
|
#define SIS_DETECT_REGISTER 0x40
|
|
|
|
static void quirk_sis_503(struct pci_dev *dev)
|
|
{
|
|
u8 reg;
|
|
u16 devid;
|
|
|
|
pci_read_config_byte(dev, SIS_DETECT_REGISTER, ®);
|
|
pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6));
|
|
pci_read_config_word(dev, PCI_DEVICE_ID, &devid);
|
|
if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) {
|
|
pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg);
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Ok, it now shows up as a 96x.. run the 96x quirk by
|
|
* hand in case it has already been processed.
|
|
* (depends on link order, which is apparently not guaranteed)
|
|
*/
|
|
dev->device = devid;
|
|
quirk_sis_96x_smbus(dev);
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503 );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503 );
|
|
|
|
|
|
/*
|
|
* On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller
|
|
* and MC97 modem controller are disabled when a second PCI soundcard is
|
|
* present. This patch, tweaking the VT8237 ISA bridge, enables them.
|
|
* -- bjd
|
|
*/
|
|
static void asus_hides_ac97_lpc(struct pci_dev *dev)
|
|
{
|
|
u8 val;
|
|
int asus_hides_ac97 = 0;
|
|
|
|
if (likely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) {
|
|
if (dev->device == PCI_DEVICE_ID_VIA_8237)
|
|
asus_hides_ac97 = 1;
|
|
}
|
|
|
|
if (!asus_hides_ac97)
|
|
return;
|
|
|
|
pci_read_config_byte(dev, 0x50, &val);
|
|
if (val & 0xc0) {
|
|
pci_write_config_byte(dev, 0x50, val & (~0xc0));
|
|
pci_read_config_byte(dev, 0x50, &val);
|
|
if (val & 0xc0)
|
|
printk(KERN_INFO "PCI: onboard AC97/MC97 devices continue to play 'hide and seek'! 0x%x\n", val);
|
|
else
|
|
printk(KERN_INFO "PCI: enabled onboard AC97/MC97 devices\n");
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc );
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc );
|
|
|
|
#if defined(CONFIG_ATA) || defined(CONFIG_ATA_MODULE)
|
|
|
|
/*
|
|
* If we are using libata we can drive this chip properly but must
|
|
* do this early on to make the additional device appear during
|
|
* the PCI scanning.
|
|
*/
|
|
static void quirk_jmicron_ata(struct pci_dev *pdev)
|
|
{
|
|
u32 conf1, conf5, class;
|
|
u8 hdr;
|
|
|
|
/* Only poke fn 0 */
|
|
if (PCI_FUNC(pdev->devfn))
|
|
return;
|
|
|
|
pci_read_config_dword(pdev, 0x40, &conf1);
|
|
pci_read_config_dword(pdev, 0x80, &conf5);
|
|
|
|
conf1 &= ~0x00CFF302; /* Clear bit 1, 8, 9, 12-19, 22, 23 */
|
|
conf5 &= ~(1 << 24); /* Clear bit 24 */
|
|
|
|
switch (pdev->device) {
|
|
case PCI_DEVICE_ID_JMICRON_JMB360:
|
|
/* The controller should be in single function ahci mode */
|
|
conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */
|
|
break;
|
|
|
|
case PCI_DEVICE_ID_JMICRON_JMB365:
|
|
case PCI_DEVICE_ID_JMICRON_JMB366:
|
|
/* Redirect IDE second PATA port to the right spot */
|
|
conf5 |= (1 << 24);
|
|
/* Fall through */
|
|
case PCI_DEVICE_ID_JMICRON_JMB361:
|
|
case PCI_DEVICE_ID_JMICRON_JMB363:
|
|
/* Enable dual function mode, AHCI on fn 0, IDE fn1 */
|
|
/* Set the class codes correctly and then direct IDE 0 */
|
|
conf1 |= 0x00C2A1B3; /* Set 0, 1, 4, 5, 7, 8, 13, 15, 17, 22, 23 */
|
|
break;
|
|
|
|
case PCI_DEVICE_ID_JMICRON_JMB368:
|
|
/* The controller should be in single function IDE mode */
|
|
conf1 |= 0x00C00000; /* Set 22, 23 */
|
|
break;
|
|
}
|
|
|
|
pci_write_config_dword(pdev, 0x40, conf1);
|
|
pci_write_config_dword(pdev, 0x80, conf5);
|
|
|
|
/* Update pdev accordingly */
|
|
pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr);
|
|
pdev->hdr_type = hdr & 0x7f;
|
|
pdev->multifunction = !!(hdr & 0x80);
|
|
|
|
pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class);
|
|
pdev->class = class >> 8;
|
|
}
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
|
|
|
|
#endif
|
|
|
|
#ifdef CONFIG_X86_IO_APIC
|
|
static void __init quirk_alder_ioapic(struct pci_dev *pdev)
|
|
{
|
|
int i;
|
|
|
|
if ((pdev->class >> 8) != 0xff00)
|
|
return;
|
|
|
|
/* the first BAR is the location of the IO APIC...we must
|
|
* not touch this (and it's already covered by the fixmap), so
|
|
* forcibly insert it into the resource tree */
|
|
if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0))
|
|
insert_resource(&iomem_resource, &pdev->resource[0]);
|
|
|
|
/* The next five BARs all seem to be rubbish, so just clean
|
|
* them out */
|
|
for (i=1; i < 6; i++) {
|
|
memset(&pdev->resource[i], 0, sizeof(pdev->resource[i]));
|
|
}
|
|
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic );
|
|
#endif
|
|
|
|
int pcie_mch_quirk;
|
|
EXPORT_SYMBOL(pcie_mch_quirk);
|
|
|
|
static void __devinit quirk_pcie_mch(struct pci_dev *pdev)
|
|
{
|
|
pcie_mch_quirk = 1;
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch );
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch );
|
|
|
|
|
|
/*
|
|
* It's possible for the MSI to get corrupted if shpc and acpi
|
|
* are used together on certain PXH-based systems.
|
|
*/
|
|
static void __devinit quirk_pcie_pxh(struct pci_dev *dev)
|
|
{
|
|
pci_msi_off(dev);
|
|
|
|
dev->no_msi = 1;
|
|
|
|
printk(KERN_WARNING "PCI: PXH quirk detected, "
|
|
"disabling MSI for SHPC device\n");
|
|
}
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh);
|
|
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh);
|
|
|
|
/*
|
|
* Some Intel PCI Express chipsets have trouble with downstream
|
|
* device power management.
|
|
*/
|
|
static void quirk_intel_pcie_pm(struct pci_dev * dev)
|
|
{
|
|
pci_pm_d3_delay = 120;
|
|
dev->no_d1d2 = 1;
|
|
}
|
|
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2601, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2602, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2603, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2604, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2605, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2606, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2607, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2608, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2609, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm);
|
|
|
|
/*
|
|
* Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size
|
|
* but the PIO transfers won't work if BAR0 falls at the odd 8 bytes.
|
|
* Re-allocate the region if needed...
|
|
*/
|
|
static void __init quirk_tc86c001_ide(struct pci_dev *dev)
|
|
{
|
|
struct resource *r = &dev->resource[0];
|
|
|
|
if (r->start & 0x8) {
|
|
r->start = 0;
|
|
r->end = 0xf;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA_2,
|
|
PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE,
|
|
quirk_tc86c001_ide);
|
|
|
|
static void __devinit quirk_netmos(struct pci_dev *dev)
|
|
{
|
|
unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4;
|
|
unsigned int num_serial = dev->subsystem_device & 0xf;
|
|
|
|
/*
|
|
* These Netmos parts are multiport serial devices with optional
|
|
* parallel ports. Even when parallel ports are present, they
|
|
* are identified as class SERIAL, which means the serial driver
|
|
* will claim them. To prevent this, mark them as class OTHER.
|
|
* These combo devices should be claimed by parport_serial.
|
|
*
|
|
* The subdevice ID is of the form 0x00PS, where <P> is the number
|
|
* of parallel ports and <S> is the number of serial ports.
|
|
*/
|
|
switch (dev->device) {
|
|
case PCI_DEVICE_ID_NETMOS_9735:
|
|
case PCI_DEVICE_ID_NETMOS_9745:
|
|
case PCI_DEVICE_ID_NETMOS_9835:
|
|
case PCI_DEVICE_ID_NETMOS_9845:
|
|
case PCI_DEVICE_ID_NETMOS_9855:
|
|
if ((dev->class >> 8) == PCI_CLASS_COMMUNICATION_SERIAL &&
|
|
num_parallel) {
|
|
printk(KERN_INFO "PCI: Netmos %04x (%u parallel, "
|
|
"%u serial); changing class SERIAL to OTHER "
|
|
"(use parport_serial)\n",
|
|
dev->device, num_parallel, num_serial);
|
|
dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) |
|
|
(dev->class & 0xff);
|
|
}
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, quirk_netmos);
|
|
|
|
static void __devinit quirk_e100_interrupt(struct pci_dev *dev)
|
|
{
|
|
u16 command;
|
|
u8 __iomem *csr;
|
|
u8 cmd_hi;
|
|
|
|
switch (dev->device) {
|
|
/* PCI IDs taken from drivers/net/e100.c */
|
|
case 0x1029:
|
|
case 0x1030 ... 0x1034:
|
|
case 0x1038 ... 0x103E:
|
|
case 0x1050 ... 0x1057:
|
|
case 0x1059:
|
|
case 0x1064 ... 0x106B:
|
|
case 0x1091 ... 0x1095:
|
|
case 0x1209:
|
|
case 0x1229:
|
|
case 0x2449:
|
|
case 0x2459:
|
|
case 0x245D:
|
|
case 0x27DC:
|
|
break;
|
|
default:
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Some firmware hands off the e100 with interrupts enabled,
|
|
* which can cause a flood of interrupts if packets are
|
|
* received before the driver attaches to the device. So
|
|
* disable all e100 interrupts here. The driver will
|
|
* re-enable them when it's ready.
|
|
*/
|
|
pci_read_config_word(dev, PCI_COMMAND, &command);
|
|
|
|
if (!(command & PCI_COMMAND_MEMORY) || !pci_resource_start(dev, 0))
|
|
return;
|
|
|
|
/* Convert from PCI bus to resource space. */
|
|
csr = ioremap(pci_resource_start(dev, 0), 8);
|
|
if (!csr) {
|
|
printk(KERN_WARNING "PCI: Can't map %s e100 registers\n",
|
|
pci_name(dev));
|
|
return;
|
|
}
|
|
|
|
cmd_hi = readb(csr + 3);
|
|
if (cmd_hi == 0) {
|
|
printk(KERN_WARNING "PCI: Firmware left %s e100 interrupts "
|
|
"enabled, disabling\n", pci_name(dev));
|
|
writeb(1, csr + 3);
|
|
}
|
|
|
|
iounmap(csr);
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, quirk_e100_interrupt);
|
|
|
|
static void __devinit fixup_rev1_53c810(struct pci_dev* dev)
|
|
{
|
|
/* rev 1 ncr53c810 chips don't set the class at all which means
|
|
* they don't get their resources remapped. Fix that here.
|
|
*/
|
|
|
|
if (dev->class == PCI_CLASS_NOT_DEFINED) {
|
|
printk(KERN_INFO "NCR 53c810 rev 1 detected, setting PCI class.\n");
|
|
dev->class = PCI_CLASS_STORAGE_SCSI;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
|
|
|
|
static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end)
|
|
{
|
|
while (f < end) {
|
|
if ((f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) &&
|
|
(f->device == dev->device || f->device == (u16) PCI_ANY_ID)) {
|
|
pr_debug("PCI: Calling quirk %p for %s\n", f->hook, pci_name(dev));
|
|
f->hook(dev);
|
|
}
|
|
f++;
|
|
}
|
|
}
|
|
|
|
extern struct pci_fixup __start_pci_fixups_early[];
|
|
extern struct pci_fixup __end_pci_fixups_early[];
|
|
extern struct pci_fixup __start_pci_fixups_header[];
|
|
extern struct pci_fixup __end_pci_fixups_header[];
|
|
extern struct pci_fixup __start_pci_fixups_final[];
|
|
extern struct pci_fixup __end_pci_fixups_final[];
|
|
extern struct pci_fixup __start_pci_fixups_enable[];
|
|
extern struct pci_fixup __end_pci_fixups_enable[];
|
|
extern struct pci_fixup __start_pci_fixups_resume[];
|
|
extern struct pci_fixup __end_pci_fixups_resume[];
|
|
|
|
|
|
void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev)
|
|
{
|
|
struct pci_fixup *start, *end;
|
|
|
|
switch(pass) {
|
|
case pci_fixup_early:
|
|
start = __start_pci_fixups_early;
|
|
end = __end_pci_fixups_early;
|
|
break;
|
|
|
|
case pci_fixup_header:
|
|
start = __start_pci_fixups_header;
|
|
end = __end_pci_fixups_header;
|
|
break;
|
|
|
|
case pci_fixup_final:
|
|
start = __start_pci_fixups_final;
|
|
end = __end_pci_fixups_final;
|
|
break;
|
|
|
|
case pci_fixup_enable:
|
|
start = __start_pci_fixups_enable;
|
|
end = __end_pci_fixups_enable;
|
|
break;
|
|
|
|
case pci_fixup_resume:
|
|
start = __start_pci_fixups_resume;
|
|
end = __end_pci_fixups_resume;
|
|
break;
|
|
|
|
default:
|
|
/* stupid compiler warning, you would think with an enum... */
|
|
return;
|
|
}
|
|
pci_do_fixups(dev, start, end);
|
|
}
|
|
EXPORT_SYMBOL(pci_fixup_device);
|
|
|
|
/* Enable 1k I/O space granularity on the Intel P64H2 */
|
|
static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
|
|
{
|
|
u16 en1k;
|
|
u8 io_base_lo, io_limit_lo;
|
|
unsigned long base, limit;
|
|
struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES;
|
|
|
|
pci_read_config_word(dev, 0x40, &en1k);
|
|
|
|
if (en1k & 0x200) {
|
|
printk(KERN_INFO "PCI: Enable I/O Space to 1 KB Granularity\n");
|
|
|
|
pci_read_config_byte(dev, PCI_IO_BASE, &io_base_lo);
|
|
pci_read_config_byte(dev, PCI_IO_LIMIT, &io_limit_lo);
|
|
base = (io_base_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8;
|
|
limit = (io_limit_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8;
|
|
|
|
if (base <= limit) {
|
|
res->start = base;
|
|
res->end = limit + 0x3ff;
|
|
}
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io);
|
|
|
|
/* Fix the IOBL_ADR for 1k I/O space granularity on the Intel P64H2
|
|
* The IOBL_ADR gets re-written to 4k boundaries in pci_setup_bridge()
|
|
* in drivers/pci/setup-bus.c
|
|
*/
|
|
static void __devinit quirk_p64h2_1k_io_fix_iobl(struct pci_dev *dev)
|
|
{
|
|
u16 en1k, iobl_adr, iobl_adr_1k;
|
|
struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES;
|
|
|
|
pci_read_config_word(dev, 0x40, &en1k);
|
|
|
|
if (en1k & 0x200) {
|
|
pci_read_config_word(dev, PCI_IO_BASE, &iobl_adr);
|
|
|
|
iobl_adr_1k = iobl_adr | (res->start >> 8) | (res->end & 0xfc00);
|
|
|
|
if (iobl_adr != iobl_adr_1k) {
|
|
printk(KERN_INFO "PCI: Fixing P64H2 IOBL_ADR from 0x%x to 0x%x for 1 KB Granularity\n",
|
|
iobl_adr,iobl_adr_1k);
|
|
pci_write_config_word(dev, PCI_IO_BASE, iobl_adr_1k);
|
|
}
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io_fix_iobl);
|
|
|
|
/* Under some circumstances, AER is not linked with extended capabilities.
|
|
* Force it to be linked by setting the corresponding control bit in the
|
|
* config space.
|
|
*/
|
|
static void quirk_nvidia_ck804_pcie_aer_ext_cap(struct pci_dev *dev)
|
|
{
|
|
uint8_t b;
|
|
if (pci_read_config_byte(dev, 0xf41, &b) == 0) {
|
|
if (!(b & 0x20)) {
|
|
pci_write_config_byte(dev, 0xf41, b | 0x20);
|
|
printk(KERN_INFO
|
|
"PCI: Linking AER extended capability on %s\n",
|
|
pci_name(dev));
|
|
}
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE,
|
|
quirk_nvidia_ck804_pcie_aer_ext_cap);
|
|
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE,
|
|
quirk_nvidia_ck804_pcie_aer_ext_cap);
|
|
|
|
#ifdef CONFIG_PCI_MSI
|
|
/* Some chipsets do not support MSI. We cannot easily rely on setting
|
|
* PCI_BUS_FLAGS_NO_MSI in its bus flags because there are actually
|
|
* some other busses controlled by the chipset even if Linux is not
|
|
* aware of it. Instead of setting the flag on all busses in the
|
|
* machine, simply disable MSI globally.
|
|
*/
|
|
static void __init quirk_disable_all_msi(struct pci_dev *dev)
|
|
{
|
|
pci_no_msi();
|
|
printk(KERN_WARNING "PCI: MSI quirk detected. MSI deactivated.\n");
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_disable_all_msi);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000_PCIX, quirk_disable_all_msi);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS400_200, quirk_disable_all_msi);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS480, quirk_disable_all_msi);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RD580, quirk_disable_all_msi);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RX790, quirk_disable_all_msi);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS690, quirk_disable_all_msi);
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3351, quirk_disable_all_msi);
|
|
|
|
/* Disable MSI on chipsets that are known to not support it */
|
|
static void __devinit quirk_disable_msi(struct pci_dev *dev)
|
|
{
|
|
if (dev->subordinate) {
|
|
printk(KERN_WARNING "PCI: MSI quirk detected. "
|
|
"PCI_BUS_FLAGS_NO_MSI set for %s subordinate bus.\n",
|
|
pci_name(dev));
|
|
dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_msi);
|
|
|
|
/* Go through the list of Hypertransport capabilities and
|
|
* return 1 if a HT MSI capability is found and enabled */
|
|
static int __devinit msi_ht_cap_enabled(struct pci_dev *dev)
|
|
{
|
|
int pos, ttl = 48;
|
|
|
|
pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
|
|
while (pos && ttl--) {
|
|
u8 flags;
|
|
|
|
if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
|
|
&flags) == 0)
|
|
{
|
|
printk(KERN_INFO "PCI: Found %s HT MSI Mapping on %s\n",
|
|
flags & HT_MSI_FLAGS_ENABLE ?
|
|
"enabled" : "disabled", pci_name(dev));
|
|
return (flags & HT_MSI_FLAGS_ENABLE) != 0;
|
|
}
|
|
|
|
pos = pci_find_next_ht_capability(dev, pos,
|
|
HT_CAPTYPE_MSI_MAPPING);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/* Check the hypertransport MSI mapping to know whether MSI is enabled or not */
|
|
static void __devinit quirk_msi_ht_cap(struct pci_dev *dev)
|
|
{
|
|
if (dev->subordinate && !msi_ht_cap_enabled(dev)) {
|
|
printk(KERN_WARNING "PCI: MSI quirk detected. "
|
|
"MSI disabled on chipset %s.\n",
|
|
pci_name(dev));
|
|
dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI;
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE,
|
|
quirk_msi_ht_cap);
|
|
|
|
/* The nVidia CK804 chipset may have 2 HT MSI mappings.
|
|
* MSI are supported if the MSI capability set in any of these mappings.
|
|
*/
|
|
static void __devinit quirk_nvidia_ck804_msi_ht_cap(struct pci_dev *dev)
|
|
{
|
|
struct pci_dev *pdev;
|
|
|
|
if (!dev->subordinate)
|
|
return;
|
|
|
|
/* check HT MSI cap on this chipset and the root one.
|
|
* a single one having MSI is enough to be sure that MSI are supported.
|
|
*/
|
|
pdev = pci_get_slot(dev->bus, 0);
|
|
if (!pdev)
|
|
return;
|
|
if (!msi_ht_cap_enabled(dev) && !msi_ht_cap_enabled(pdev)) {
|
|
printk(KERN_WARNING "PCI: MSI quirk detected. "
|
|
"MSI disabled on chipset %s.\n",
|
|
pci_name(dev));
|
|
dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI;
|
|
}
|
|
pci_dev_put(pdev);
|
|
}
|
|
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE,
|
|
quirk_nvidia_ck804_msi_ht_cap);
|
|
#endif /* CONFIG_PCI_MSI */
|