0ea6e61122
Below you will find an updated version from the original series bunching all patches into one big patch updating broken web addresses that are located in Documentation/* Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult, the best way to deal with these is to use web.archive.org to locate these addresses that are outdated. Now there are also some addresses pointing to .spec files some are located, but some(after searching on the companies site)where still no where to be found. In this case I just changed the address to the company site this way the users can contact the company and they can locate them for the users. Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Cc: Paulo Marques <pmarques@grupopie.com> Cc: Randy Dunlap <rdunlap@xenotime.net> Cc: Michael Neuling <mikey@neuling.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
40 lines
1.8 KiB
Plaintext
40 lines
1.8 KiB
Plaintext
Itsy is a research project done by the Western Research Lab, and Systems
|
|
Research Center in Palo Alto, CA. The Itsy project is one of several
|
|
research projects at Compaq that are related to pocket computing.
|
|
|
|
For more information, see:
|
|
|
|
http://www.hpl.hp.com/downloads/crl/itsy/
|
|
|
|
Notes on initial 2.4 Itsy support (8/27/2000) :
|
|
The port was done on an Itsy version 1.5 machine with a daughtercard with
|
|
64 Meg of DRAM and 32 Meg of Flash. The initial work includes support for
|
|
serial console (to see what you're doing). No other devices have been
|
|
enabled.
|
|
|
|
To build, do a "make menuconfig" (or xmenuconfig) and select Itsy support.
|
|
Disable Flash and LCD support. and then do a make zImage.
|
|
Finally, you will need to cd to arch/arm/boot/tools and execute a make there
|
|
to build the params-itsy program used to boot the kernel.
|
|
|
|
In order to install the port of 2.4 to the itsy, You will need to set the
|
|
configuration parameters in the monitor as follows:
|
|
Arg 1:0x08340000, Arg2: 0xC0000000, Arg3:18 (0x12), Arg4:0
|
|
Make sure the start-routine address is set to 0x00060000.
|
|
|
|
Next, flash the params-itsy program to 0x00060000 ("p 1 0x00060000" in the
|
|
flash menu) Flash the kernel in arch/arm/boot/zImage into 0x08340000
|
|
("p 1 0x00340000"). Finally flash an initial ramdisk into 0xC8000000
|
|
("p 2 0x0") We used ramdisk-2-30.gz from the 0.11 version directory on
|
|
handhelds.org.
|
|
|
|
The serial connection we established was at:
|
|
8-bit data, no parity, 1 stop bit(s), 115200.00 b/s. in the monitor, in the
|
|
params-itsy program, and in the kernel itself. This can be changed, but
|
|
not easily. The monitor parameters are easily changed, the params program
|
|
setup is assembly outl's, and the kernel is a configuration item specific to
|
|
the itsy. (i.e. grep for CONFIG_SA1100_ITSY and you'll find where it is.)
|
|
|
|
|
|
This should get you a properly booting 2.4 kernel on the itsy.
|