1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
183 lines
5.3 KiB
C
183 lines
5.3 KiB
C
/*
|
|
* Copyright 2000 MontaVista Software Inc.
|
|
* Author: MontaVista Software, Inc.
|
|
* ppopov@mvista.com or source@mvista.com
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
|
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
|
|
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
|
|
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
|
|
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* You should have received a copy of the GNU General Public License along
|
|
* with this program; if not, write to the Free Software Foundation, Inc.,
|
|
* 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
#include <linux/config.h>
|
|
#include <linux/init.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/console.h>
|
|
#include <linux/delay.h>
|
|
|
|
#include <asm/cpu.h>
|
|
#include <asm/bootinfo.h>
|
|
#include <asm/irq.h>
|
|
#include <asm/mipsregs.h>
|
|
#include <asm/reboot.h>
|
|
#include <asm/pgtable.h>
|
|
#include <asm/mach-au1x00/au1000.h>
|
|
#include <asm/mach-pb1x00/pb1000.h>
|
|
|
|
void board_reset (void)
|
|
{
|
|
}
|
|
|
|
void __init board_setup(void)
|
|
{
|
|
u32 pin_func, static_cfg0;
|
|
u32 sys_freqctrl, sys_clksrc;
|
|
u32 prid = read_c0_prid();
|
|
|
|
// set AUX clock to 12MHz * 8 = 96 MHz
|
|
au_writel(8, SYS_AUXPLL);
|
|
au_writel(0, SYS_PINSTATERD);
|
|
udelay(100);
|
|
|
|
#if defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE)
|
|
/* zero and disable FREQ2 */
|
|
sys_freqctrl = au_readl(SYS_FREQCTRL0);
|
|
sys_freqctrl &= ~0xFFF00000;
|
|
au_writel(sys_freqctrl, SYS_FREQCTRL0);
|
|
|
|
/* zero and disable USBH/USBD clocks */
|
|
sys_clksrc = au_readl(SYS_CLKSRC);
|
|
sys_clksrc &= ~0x00007FE0;
|
|
au_writel(sys_clksrc, SYS_CLKSRC);
|
|
|
|
sys_freqctrl = au_readl(SYS_FREQCTRL0);
|
|
sys_freqctrl &= ~0xFFF00000;
|
|
|
|
sys_clksrc = au_readl(SYS_CLKSRC);
|
|
sys_clksrc &= ~0x00007FE0;
|
|
|
|
switch (prid & 0x000000FF)
|
|
{
|
|
case 0x00: /* DA */
|
|
case 0x01: /* HA */
|
|
case 0x02: /* HB */
|
|
/* CPU core freq to 48MHz to slow it way down... */
|
|
au_writel(4, SYS_CPUPLL);
|
|
|
|
/*
|
|
* Setup 48MHz FREQ2 from CPUPLL for USB Host
|
|
*/
|
|
/* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */
|
|
sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20));
|
|
au_writel(sys_freqctrl, SYS_FREQCTRL0);
|
|
|
|
/* CPU core freq to 384MHz */
|
|
au_writel(0x20, SYS_CPUPLL);
|
|
|
|
printk("Au1000: 48MHz OHCI workaround enabled\n");
|
|
break;
|
|
|
|
default: /* HC and newer */
|
|
// FREQ2 = aux/2 = 48 MHz
|
|
sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
|
|
au_writel(sys_freqctrl, SYS_FREQCTRL0);
|
|
break;
|
|
}
|
|
|
|
/*
|
|
* Route 48MHz FREQ2 into USB Host and/or Device
|
|
*/
|
|
#ifdef CONFIG_USB_OHCI
|
|
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
|
|
#endif
|
|
#ifdef CONFIG_AU1X00_USB_DEVICE
|
|
sys_clksrc |= ((4<<7) | (0<<6) | (0<<5));
|
|
#endif
|
|
au_writel(sys_clksrc, SYS_CLKSRC);
|
|
|
|
// configure pins GPIO[14:9] as GPIO
|
|
pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8080);
|
|
|
|
#ifndef CONFIG_AU1X00_USB_DEVICE
|
|
// 2nd USB port is USB host
|
|
pin_func |= 0x8000;
|
|
#endif
|
|
au_writel(pin_func, SYS_PINFUNC);
|
|
au_writel(0x2800, SYS_TRIOUTCLR);
|
|
au_writel(0x0030, SYS_OUTPUTCLR);
|
|
#endif // defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE)
|
|
|
|
// make gpio 15 an input (for interrupt line)
|
|
pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x100);
|
|
// we don't need I2S, so make it available for GPIO[31:29]
|
|
pin_func |= (1<<5);
|
|
au_writel(pin_func, SYS_PINFUNC);
|
|
|
|
au_writel(0x8000, SYS_TRIOUTCLR);
|
|
|
|
static_cfg0 = au_readl(MEM_STCFG0) & (u32)(~0xc00);
|
|
au_writel(static_cfg0, MEM_STCFG0);
|
|
|
|
// configure RCE2* for LCD
|
|
au_writel(0x00000004, MEM_STCFG2);
|
|
|
|
// MEM_STTIME2
|
|
au_writel(0x09000000, MEM_STTIME2);
|
|
|
|
// Set 32-bit base address decoding for RCE2*
|
|
au_writel(0x10003ff0, MEM_STADDR2);
|
|
|
|
// PCI CPLD setup
|
|
// expand CE0 to cover PCI
|
|
au_writel(0x11803e40, MEM_STADDR1);
|
|
|
|
// burst visibility on
|
|
au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0);
|
|
|
|
au_writel(0x83, MEM_STCFG1); // ewait enabled, flash timing
|
|
au_writel(0x33030a10, MEM_STTIME1); // slower timing for FPGA
|
|
|
|
/* setup the static bus controller */
|
|
au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
|
|
au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
|
|
au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
|
|
|
|
#ifdef CONFIG_PCI
|
|
au_writel(0, PCI_BRIDGE_CONFIG); // set extend byte to 0
|
|
au_writel(0, SDRAM_MBAR); // set mbar to 0
|
|
au_writel(0x2, SDRAM_CMD); // enable memory accesses
|
|
au_sync_delay(1);
|
|
#endif
|
|
|
|
/* Enable Au1000 BCLK switching - note: sed1356 must not use
|
|
* its BCLK (Au1000 LCLK) for any timings */
|
|
switch (prid & 0x000000FF)
|
|
{
|
|
case 0x00: /* DA */
|
|
case 0x01: /* HA */
|
|
case 0x02: /* HB */
|
|
break;
|
|
default: /* HC and newer */
|
|
/* Enable sys bus clock divider when IDLE state or no bus
|
|
activity. */
|
|
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
|
|
break;
|
|
}
|
|
}
|