d61780c0d3
Removed some more references to check_region(). I checked these changes into the 'checkreg' branch of rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git The only valid references remaining are in: drivers/scsi/advansys.c drivers/scsi/BusLogic.c drivers/cdrom/sbpcd.c sound/oss/pss.c Remove last vestiges of ide_check_region() drivers/char/specialix: trim trailing whitespace drivers/char/specialix: eliminate use of check_region() Remove outdated and unused references to check_region() [sound oss] remove check_region() usage from cs4232, wavfront [netdrvr eepro] trim trailing whitespace [netdrvr eepro] remove check_region() usage Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
523 lines
13 KiB
C
523 lines
13 KiB
C
/*
|
|
* Copyright (C) by Hannu Savolainen 1993-1997
|
|
*
|
|
* cs4232.c
|
|
*
|
|
* The low level driver for Crystal CS4232 based cards. The CS4232 is
|
|
* a PnP compatible chip which contains a CS4231A codec, SB emulation,
|
|
* a MPU401 compatible MIDI port, joystick and synthesizer and IDE CD-ROM
|
|
* interfaces. This is just a temporary driver until full PnP support
|
|
* gets implemented. Just the WSS codec, FM synth and the MIDI ports are
|
|
* supported. Other interfaces are left uninitialized.
|
|
*
|
|
* ifdef ...WAVEFRONT...
|
|
*
|
|
* Support is provided for initializing the WaveFront synth
|
|
* interface as well, which is logical device #4. Note that if
|
|
* you have a Tropez+ card, you probably don't need to setup
|
|
* the CS4232-supported MIDI interface, since it corresponds to
|
|
* the internal 26-pin header that's hard to access. Using this
|
|
* requires an additional IRQ, a resource none too plentiful in
|
|
* this environment. Just don't set module parameters mpuio and
|
|
* mpuirq, and the MIDI port will be left uninitialized. You can
|
|
* still use the ICS2115 hosted MIDI interface which corresponds
|
|
* to the 9-pin D connector on the back of the card.
|
|
*
|
|
* endif ...WAVEFRONT...
|
|
*
|
|
* Supported chips are:
|
|
* CS4232
|
|
* CS4236
|
|
* CS4236B
|
|
*
|
|
* Note: You will need a PnP config setup to initialise some CS4232 boards
|
|
* anyway.
|
|
*
|
|
* Changes
|
|
* John Rood Added Bose Sound System Support.
|
|
* Toshio Spoor
|
|
* Alan Cox Modularisation, Basic cleanups.
|
|
* Paul Barton-Davis Separated MPU configuration, added
|
|
* Tropez+ (WaveFront) support
|
|
* Christoph Hellwig Adapted to module_init/module_exit,
|
|
* simple cleanups
|
|
* Arnaldo C. de Melo got rid of attach_uart401
|
|
* Bartlomiej Zolnierkiewicz
|
|
* Added some __init/__initdata/__exit
|
|
* Marcus Meissner Added ISA PnP support.
|
|
*/
|
|
|
|
#include <linux/config.h>
|
|
#include <linux/pnp.h>
|
|
#include <linux/module.h>
|
|
#include <linux/init.h>
|
|
|
|
#include "sound_config.h"
|
|
|
|
#include "ad1848.h"
|
|
#include "mpu401.h"
|
|
|
|
#define KEY_PORT 0x279 /* Same as LPT1 status port */
|
|
#define CSN_NUM 0x99 /* Just a random number */
|
|
#define INDEX_ADDRESS 0x00 /* (R0) Index Address Register */
|
|
#define INDEX_DATA 0x01 /* (R1) Indexed Data Register */
|
|
#define PIN_CONTROL 0x0a /* (I10) Pin Control */
|
|
#define ENABLE_PINS 0xc0 /* XCTRL0/XCTRL1 enable */
|
|
|
|
static void CS_OUT(unsigned char a)
|
|
{
|
|
outb(a, KEY_PORT);
|
|
}
|
|
|
|
#define CS_OUT2(a, b) {CS_OUT(a);CS_OUT(b);}
|
|
#define CS_OUT3(a, b, c) {CS_OUT(a);CS_OUT(b);CS_OUT(c);}
|
|
|
|
static int __initdata bss = 0;
|
|
static int mpu_base, mpu_irq;
|
|
static int synth_base, synth_irq;
|
|
static int mpu_detected;
|
|
|
|
static int probe_cs4232_mpu(struct address_info *hw_config)
|
|
{
|
|
/*
|
|
* Just write down the config values.
|
|
*/
|
|
|
|
mpu_base = hw_config->io_base;
|
|
mpu_irq = hw_config->irq;
|
|
|
|
return 1;
|
|
}
|
|
|
|
static unsigned char crystal_key[] = /* A 32 byte magic key sequence */
|
|
{
|
|
0x96, 0x35, 0x9a, 0xcd, 0xe6, 0xf3, 0x79, 0xbc,
|
|
0x5e, 0xaf, 0x57, 0x2b, 0x15, 0x8a, 0xc5, 0xe2,
|
|
0xf1, 0xf8, 0x7c, 0x3e, 0x9f, 0x4f, 0x27, 0x13,
|
|
0x09, 0x84, 0x42, 0xa1, 0xd0, 0x68, 0x34, 0x1a
|
|
};
|
|
|
|
static void sleep(unsigned howlong)
|
|
{
|
|
current->state = TASK_INTERRUPTIBLE;
|
|
schedule_timeout(howlong);
|
|
}
|
|
|
|
static void enable_xctrl(int baseio)
|
|
{
|
|
unsigned char regd;
|
|
|
|
/*
|
|
* Some IBM Aptiva's have the Bose Sound System. By default
|
|
* the Bose Amplifier is disabled. The amplifier will be
|
|
* activated, by setting the XCTRL0 and XCTRL1 bits.
|
|
* Volume of the monitor bose speakers/woofer, can then
|
|
* be set by changing the PCM volume.
|
|
*
|
|
*/
|
|
|
|
printk("cs4232: enabling Bose Sound System Amplifier.\n");
|
|
|
|
/* Switch to Pin Control Address */
|
|
regd = inb(baseio + INDEX_ADDRESS) & 0xe0;
|
|
outb(((unsigned char) (PIN_CONTROL | regd)), baseio + INDEX_ADDRESS );
|
|
|
|
/* Activate the XCTRL0 and XCTRL1 Pins */
|
|
regd = inb(baseio + INDEX_DATA);
|
|
outb(((unsigned char) (ENABLE_PINS | regd)), baseio + INDEX_DATA );
|
|
}
|
|
|
|
static int __init probe_cs4232(struct address_info *hw_config, int isapnp_configured)
|
|
{
|
|
int i, n;
|
|
int base = hw_config->io_base, irq = hw_config->irq;
|
|
int dma1 = hw_config->dma, dma2 = hw_config->dma2;
|
|
struct resource *ports;
|
|
|
|
if (base == -1 || irq == -1 || dma1 == -1) {
|
|
printk(KERN_ERR "cs4232: dma, irq and io must be set.\n");
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Verify that the I/O port range is free.
|
|
*/
|
|
|
|
ports = request_region(base, 4, "ad1848");
|
|
if (!ports) {
|
|
printk(KERN_ERR "cs4232.c: I/O port 0x%03x not free\n", base);
|
|
return 0;
|
|
}
|
|
if (ad1848_detect(ports, NULL, hw_config->osp)) {
|
|
goto got_it; /* The card is already active */
|
|
}
|
|
if (isapnp_configured) {
|
|
printk(KERN_ERR "cs4232.c: ISA PnP configured, but not detected?\n");
|
|
goto fail;
|
|
}
|
|
|
|
/*
|
|
* This version of the driver doesn't use the PnP method when configuring
|
|
* the card but a simplified method defined by Crystal. This means that
|
|
* just one CS4232 compatible device can exist on the system. Also this
|
|
* method conflicts with possible PnP support in the OS. For this reason
|
|
* driver is just a temporary kludge.
|
|
*
|
|
* Also the Cirrus/Crystal method doesn't always work. Try ISA PnP first ;)
|
|
*/
|
|
|
|
/*
|
|
* Repeat initialization few times since it doesn't always succeed in
|
|
* first time.
|
|
*/
|
|
|
|
for (n = 0; n < 4; n++)
|
|
{
|
|
/*
|
|
* Wake up the card by sending a 32 byte Crystal key to the key port.
|
|
*/
|
|
|
|
for (i = 0; i < 32; i++)
|
|
CS_OUT(crystal_key[i]);
|
|
|
|
sleep(HZ / 10);
|
|
|
|
/*
|
|
* Now set the CSN (Card Select Number).
|
|
*/
|
|
|
|
CS_OUT2(0x06, CSN_NUM);
|
|
|
|
/*
|
|
* Then set some config bytes. First logical device 0
|
|
*/
|
|
|
|
CS_OUT2(0x15, 0x00); /* Select logical device 0 (WSS/SB/FM) */
|
|
CS_OUT3(0x47, (base >> 8) & 0xff, base & 0xff); /* WSS base */
|
|
|
|
if (!request_region(0x388, 4, "FM")) /* Not free */
|
|
CS_OUT3(0x48, 0x00, 0x00) /* FM base off */
|
|
else {
|
|
release_region(0x388, 4);
|
|
CS_OUT3(0x48, 0x03, 0x88); /* FM base 0x388 */
|
|
}
|
|
|
|
CS_OUT3(0x42, 0x00, 0x00); /* SB base off */
|
|
CS_OUT2(0x22, irq); /* SB+WSS IRQ */
|
|
CS_OUT2(0x2a, dma1); /* SB+WSS DMA */
|
|
|
|
if (dma2 != -1)
|
|
CS_OUT2(0x25, dma2) /* WSS DMA2 */
|
|
else
|
|
CS_OUT2(0x25, 4); /* No WSS DMA2 */
|
|
|
|
CS_OUT2(0x33, 0x01); /* Activate logical dev 0 */
|
|
|
|
sleep(HZ / 10);
|
|
|
|
/*
|
|
* Initialize logical device 3 (MPU)
|
|
*/
|
|
|
|
if (mpu_base != 0 && mpu_irq != 0)
|
|
{
|
|
CS_OUT2(0x15, 0x03); /* Select logical device 3 (MPU) */
|
|
CS_OUT3(0x47, (mpu_base >> 8) & 0xff, mpu_base & 0xff); /* MPU base */
|
|
CS_OUT2(0x22, mpu_irq); /* MPU IRQ */
|
|
CS_OUT2(0x33, 0x01); /* Activate logical dev 3 */
|
|
}
|
|
|
|
if(synth_base != 0)
|
|
{
|
|
CS_OUT2 (0x15, 0x04); /* logical device 4 (WaveFront) */
|
|
CS_OUT3 (0x47, (synth_base >> 8) & 0xff,
|
|
synth_base & 0xff); /* base */
|
|
CS_OUT2 (0x22, synth_irq); /* IRQ */
|
|
CS_OUT2 (0x33, 0x01); /* Activate logical dev 4 */
|
|
}
|
|
|
|
/*
|
|
* Finally activate the chip
|
|
*/
|
|
|
|
CS_OUT(0x79);
|
|
|
|
sleep(HZ / 5);
|
|
|
|
/*
|
|
* Then try to detect the codec part of the chip
|
|
*/
|
|
|
|
if (ad1848_detect(ports, NULL, hw_config->osp))
|
|
goto got_it;
|
|
|
|
sleep(HZ);
|
|
}
|
|
fail:
|
|
release_region(base, 4);
|
|
return 0;
|
|
|
|
got_it:
|
|
if (dma2 == -1)
|
|
dma2 = dma1;
|
|
|
|
hw_config->slots[0] = ad1848_init("Crystal audio controller", ports,
|
|
irq,
|
|
dma1, /* Playback DMA */
|
|
dma2, /* Capture DMA */
|
|
0,
|
|
hw_config->osp,
|
|
THIS_MODULE);
|
|
|
|
if (hw_config->slots[0] != -1 &&
|
|
audio_devs[hw_config->slots[0]]->mixer_dev!=-1)
|
|
{
|
|
/* Assume the mixer map is as suggested in the CS4232 databook */
|
|
AD1848_REROUTE(SOUND_MIXER_LINE1, SOUND_MIXER_LINE);
|
|
AD1848_REROUTE(SOUND_MIXER_LINE2, SOUND_MIXER_CD);
|
|
AD1848_REROUTE(SOUND_MIXER_LINE3, SOUND_MIXER_SYNTH); /* FM synth */
|
|
}
|
|
if (mpu_base != 0 && mpu_irq != 0)
|
|
{
|
|
static struct address_info hw_config2 = {
|
|
0
|
|
}; /* Ensure it's initialized */
|
|
|
|
hw_config2.io_base = mpu_base;
|
|
hw_config2.irq = mpu_irq;
|
|
hw_config2.dma = -1;
|
|
hw_config2.dma2 = -1;
|
|
hw_config2.always_detect = 0;
|
|
hw_config2.name = NULL;
|
|
hw_config2.driver_use_1 = 0;
|
|
hw_config2.driver_use_2 = 0;
|
|
hw_config2.card_subtype = 0;
|
|
|
|
if (probe_uart401(&hw_config2, THIS_MODULE))
|
|
{
|
|
mpu_detected = 1;
|
|
}
|
|
else
|
|
{
|
|
mpu_base = mpu_irq = 0;
|
|
}
|
|
hw_config->slots[1] = hw_config2.slots[1];
|
|
}
|
|
|
|
if (bss)
|
|
enable_xctrl(base);
|
|
|
|
return 1;
|
|
}
|
|
|
|
static void __devexit unload_cs4232(struct address_info *hw_config)
|
|
{
|
|
int base = hw_config->io_base, irq = hw_config->irq;
|
|
int dma1 = hw_config->dma, dma2 = hw_config->dma2;
|
|
|
|
if (dma2 == -1)
|
|
dma2 = dma1;
|
|
|
|
ad1848_unload(base,
|
|
irq,
|
|
dma1, /* Playback DMA */
|
|
dma2, /* Capture DMA */
|
|
0);
|
|
|
|
sound_unload_audiodev(hw_config->slots[0]);
|
|
if (mpu_base != 0 && mpu_irq != 0 && mpu_detected)
|
|
{
|
|
static struct address_info hw_config2 =
|
|
{
|
|
0
|
|
}; /* Ensure it's initialized */
|
|
|
|
hw_config2.io_base = mpu_base;
|
|
hw_config2.irq = mpu_irq;
|
|
hw_config2.dma = -1;
|
|
hw_config2.dma2 = -1;
|
|
hw_config2.always_detect = 0;
|
|
hw_config2.name = NULL;
|
|
hw_config2.driver_use_1 = 0;
|
|
hw_config2.driver_use_2 = 0;
|
|
hw_config2.card_subtype = 0;
|
|
hw_config2.slots[1] = hw_config->slots[1];
|
|
|
|
unload_uart401(&hw_config2);
|
|
}
|
|
}
|
|
|
|
static struct address_info cfg;
|
|
static struct address_info cfg_mpu;
|
|
|
|
static int __initdata io = -1;
|
|
static int __initdata irq = -1;
|
|
static int __initdata dma = -1;
|
|
static int __initdata dma2 = -1;
|
|
static int __initdata mpuio = -1;
|
|
static int __initdata mpuirq = -1;
|
|
static int __initdata synthio = -1;
|
|
static int __initdata synthirq = -1;
|
|
static int __initdata isapnp = 1;
|
|
|
|
MODULE_DESCRIPTION("CS4232 based soundcard driver");
|
|
MODULE_AUTHOR("Hannu Savolainen, Paul Barton-Davis");
|
|
MODULE_LICENSE("GPL");
|
|
|
|
module_param(io, int, 0);
|
|
MODULE_PARM_DESC(io,"base I/O port for AD1848");
|
|
module_param(irq, int, 0);
|
|
MODULE_PARM_DESC(irq,"IRQ for AD1848 chip");
|
|
module_param(dma, int, 0);
|
|
MODULE_PARM_DESC(dma,"8 bit DMA for AD1848 chip");
|
|
module_param(dma2, int, 0);
|
|
MODULE_PARM_DESC(dma2,"16 bit DMA for AD1848 chip");
|
|
module_param(mpuio, int, 0);
|
|
MODULE_PARM_DESC(mpuio,"MPU 401 base address");
|
|
module_param(mpuirq, int, 0);
|
|
MODULE_PARM_DESC(mpuirq,"MPU 401 IRQ");
|
|
module_param(synthio, int, 0);
|
|
MODULE_PARM_DESC(synthio,"Maui WaveTable base I/O port");
|
|
module_param(synthirq, int, 0);
|
|
MODULE_PARM_DESC(synthirq,"Maui WaveTable IRQ");
|
|
module_param(isapnp, bool, 0);
|
|
MODULE_PARM_DESC(isapnp,"Enable ISAPnP probing (default 1)");
|
|
module_param(bss, bool, 0);
|
|
MODULE_PARM_DESC(bss,"Enable Bose Sound System Support (default 0)");
|
|
|
|
/*
|
|
* Install a CS4232 based card. Need to have ad1848 and mpu401
|
|
* loaded ready.
|
|
*/
|
|
|
|
/* All cs4232 based cards have the main ad1848 card either as CSC0000 or
|
|
* CSC0100. */
|
|
static const struct pnp_device_id cs4232_pnp_table[] = {
|
|
{ .id = "CSC0100", .driver_data = 0 },
|
|
{ .id = "CSC0000", .driver_data = 0 },
|
|
/* Guillemot Turtlebeach something appears to be cs4232 compatible
|
|
* (untested) */
|
|
{ .id = "GIM0100", .driver_data = 0 },
|
|
{ .id = ""}
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(pnp, cs4232_pnp_table);
|
|
|
|
static int cs4232_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
|
|
{
|
|
struct address_info *isapnpcfg;
|
|
|
|
isapnpcfg=(struct address_info*)kmalloc(sizeof(*isapnpcfg),GFP_KERNEL);
|
|
if (!isapnpcfg)
|
|
return -ENOMEM;
|
|
|
|
isapnpcfg->irq = pnp_irq(dev, 0);
|
|
isapnpcfg->dma = pnp_dma(dev, 0);
|
|
isapnpcfg->dma2 = pnp_dma(dev, 1);
|
|
isapnpcfg->io_base = pnp_port_start(dev, 0);
|
|
if (probe_cs4232(isapnpcfg,TRUE) == 0) {
|
|
printk(KERN_ERR "cs4232: ISA PnP card found, but not detected?\n");
|
|
kfree(isapnpcfg);
|
|
return -ENODEV;
|
|
}
|
|
pnp_set_drvdata(dev,isapnpcfg);
|
|
return 0;
|
|
}
|
|
|
|
static void __devexit cs4232_pnp_remove(struct pnp_dev *dev)
|
|
{
|
|
struct address_info *cfg = pnp_get_drvdata(dev);
|
|
if (cfg) {
|
|
unload_cs4232(cfg);
|
|
kfree(cfg);
|
|
}
|
|
}
|
|
|
|
static struct pnp_driver cs4232_driver = {
|
|
.name = "cs4232",
|
|
.id_table = cs4232_pnp_table,
|
|
.probe = cs4232_pnp_probe,
|
|
.remove = __devexit_p(cs4232_pnp_remove),
|
|
};
|
|
|
|
static int __init init_cs4232(void)
|
|
{
|
|
#ifdef CONFIG_SOUND_WAVEFRONT_MODULE
|
|
if(synthio == -1)
|
|
printk(KERN_INFO "cs4232: set synthio and synthirq to use the wavefront facilities.\n");
|
|
else {
|
|
synth_base = synthio;
|
|
synth_irq = synthirq;
|
|
}
|
|
#else
|
|
if(synthio != -1)
|
|
printk(KERN_WARNING "cs4232: wavefront support not enabled in this driver.\n");
|
|
#endif
|
|
cfg.irq = -1;
|
|
|
|
if (isapnp &&
|
|
(pnp_register_driver(&cs4232_driver) > 0)
|
|
)
|
|
return 0;
|
|
|
|
if(io==-1||irq==-1||dma==-1)
|
|
{
|
|
printk(KERN_ERR "cs4232: Must set io, irq and dma.\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
cfg.io_base = io;
|
|
cfg.irq = irq;
|
|
cfg.dma = dma;
|
|
cfg.dma2 = dma2;
|
|
|
|
cfg_mpu.io_base = -1;
|
|
cfg_mpu.irq = -1;
|
|
|
|
if (mpuio != -1 && mpuirq != -1) {
|
|
cfg_mpu.io_base = mpuio;
|
|
cfg_mpu.irq = mpuirq;
|
|
probe_cs4232_mpu(&cfg_mpu); /* Bug always returns 0 not OK -- AC */
|
|
}
|
|
|
|
if (probe_cs4232(&cfg,FALSE) == 0)
|
|
return -ENODEV;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void __exit cleanup_cs4232(void)
|
|
{
|
|
pnp_unregister_driver(&cs4232_driver);
|
|
if (cfg.irq != -1)
|
|
unload_cs4232(&cfg); /* Unloads global MPU as well, if needed */
|
|
}
|
|
|
|
module_init(init_cs4232);
|
|
module_exit(cleanup_cs4232);
|
|
|
|
#ifndef MODULE
|
|
static int __init setup_cs4232(char *str)
|
|
{
|
|
/* io, irq, dma, dma2 mpuio, mpuirq*/
|
|
int ints[7];
|
|
|
|
/* If we have isapnp cards, no need for options */
|
|
if (pnp_register_driver(&cs4232_driver) > 0)
|
|
return 1;
|
|
|
|
str = get_options(str, ARRAY_SIZE(ints), ints);
|
|
|
|
io = ints[1];
|
|
irq = ints[2];
|
|
dma = ints[3];
|
|
dma2 = ints[4];
|
|
mpuio = ints[5];
|
|
mpuirq = ints[6];
|
|
|
|
return 1;
|
|
}
|
|
|
|
__setup("cs4232=", setup_cs4232);
|
|
#endif
|