711fa80968
Get all of the defconfigs building again. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
197 lines
4.4 KiB
C
197 lines
4.4 KiB
C
/*
|
|
* linux/arch/sh/kernel/setup_7751se.c
|
|
*
|
|
* Copyright (C) 2000 Kazumoto Kojima
|
|
*
|
|
* Hitachi SolutionEngine Support.
|
|
*
|
|
* Modified for 7751 Solution Engine by
|
|
* Ian da Silva and Jeremy Siegel, 2001.
|
|
*/
|
|
#include <linux/init.h>
|
|
#include <asm/machvec.h>
|
|
#include <asm/se7751.h>
|
|
#include <asm/io.h>
|
|
|
|
void heartbeat_7751se(void);
|
|
void init_7751se_IRQ(void);
|
|
|
|
#ifdef CONFIG_SH_KGDB
|
|
#include <asm/kgdb.h>
|
|
static int kgdb_uart_setup(void);
|
|
static struct kgdb_sermap kgdb_uart_sermap =
|
|
{ "ttyS", 0, kgdb_uart_setup, NULL };
|
|
#endif
|
|
|
|
/*
|
|
* Initialize the board
|
|
*/
|
|
static void __init sh7751se_setup(char **cmdline_p)
|
|
{
|
|
/* Call init_smsc() replacement to set up SuperIO. */
|
|
/* XXX: RTC setting comes here */
|
|
#ifdef CONFIG_SH_KGDB
|
|
kgdb_register_sermap(&kgdb_uart_sermap);
|
|
#endif
|
|
}
|
|
|
|
/*********************************************************************
|
|
* Currently a hack (e.g. does not interact well w/serial.c, lots of *
|
|
* hardcoded stuff) but may be useful if SCI/F needs debugging. *
|
|
* Mostly copied from x86 code (see files asm-i386/kgdb_local.h and *
|
|
* arch/i386/lib/kgdb_serial.c). *
|
|
*********************************************************************/
|
|
|
|
#ifdef CONFIG_SH_KGDB
|
|
#include <linux/types.h>
|
|
#include <linux/serial.h>
|
|
#include <linux/serialP.h>
|
|
#include <linux/serial_reg.h>
|
|
|
|
#define COM1_PORT 0x3f8 /* Base I/O address */
|
|
#define COM1_IRQ 4 /* IRQ not used yet */
|
|
#define COM2_PORT 0x2f8 /* Base I/O address */
|
|
#define COM2_IRQ 3 /* IRQ not used yet */
|
|
|
|
#define SB_CLOCK 1843200 /* Serial baud clock */
|
|
#define SB_BASE (SB_CLOCK/16)
|
|
#define SB_MCR UART_MCR_OUT2 | UART_MCR_DTR | UART_MCR_RTS
|
|
|
|
struct uart_port {
|
|
int base;
|
|
};
|
|
#define UART_NPORTS 2
|
|
struct uart_port uart_ports[] = {
|
|
{ COM1_PORT },
|
|
{ COM2_PORT },
|
|
};
|
|
struct uart_port *kgdb_uart_port;
|
|
|
|
#define UART_IN(reg) inb_p(kgdb_uart_port->base + reg)
|
|
#define UART_OUT(reg,v) outb_p((v), kgdb_uart_port->base + reg)
|
|
|
|
/* Basic read/write functions for the UART */
|
|
#define UART_LSR_RXCERR (UART_LSR_BI | UART_LSR_FE | UART_LSR_PE)
|
|
static int kgdb_uart_getchar(void)
|
|
{
|
|
int lsr;
|
|
int c = -1;
|
|
|
|
while (c == -1) {
|
|
lsr = UART_IN(UART_LSR);
|
|
if (lsr & UART_LSR_DR)
|
|
c = UART_IN(UART_RX);
|
|
if ((lsr & UART_LSR_RXCERR))
|
|
c = -1;
|
|
}
|
|
return c;
|
|
}
|
|
|
|
static void kgdb_uart_putchar(int c)
|
|
{
|
|
while ((UART_IN(UART_LSR) & UART_LSR_THRE) == 0)
|
|
;
|
|
UART_OUT(UART_TX, c);
|
|
}
|
|
|
|
/*
|
|
* Initialize UART to configured/requested values.
|
|
* (But we don't interrupts yet, or interact w/serial.c)
|
|
*/
|
|
static int kgdb_uart_setup(void)
|
|
{
|
|
int port;
|
|
int lcr = 0;
|
|
int bdiv = 0;
|
|
|
|
if (kgdb_portnum >= UART_NPORTS) {
|
|
KGDB_PRINTK("uart port %d invalid.\n", kgdb_portnum);
|
|
return -1;
|
|
}
|
|
|
|
kgdb_uart_port = &uart_ports[kgdb_portnum];
|
|
|
|
/* Init sequence from gdb_hook_interrupt */
|
|
UART_IN(UART_RX);
|
|
UART_OUT(UART_IER, 0);
|
|
|
|
UART_IN(UART_RX); /* Serial driver comments say */
|
|
UART_IN(UART_IIR); /* this clears interrupt regs */
|
|
UART_IN(UART_MSR);
|
|
|
|
/* Figure basic LCR values */
|
|
switch (kgdb_bits) {
|
|
case '7':
|
|
lcr |= UART_LCR_WLEN7;
|
|
break;
|
|
default: case '8':
|
|
lcr |= UART_LCR_WLEN8;
|
|
break;
|
|
}
|
|
switch (kgdb_parity) {
|
|
case 'O':
|
|
lcr |= UART_LCR_PARITY;
|
|
break;
|
|
case 'E':
|
|
lcr |= (UART_LCR_PARITY | UART_LCR_EPAR);
|
|
break;
|
|
default: break;
|
|
}
|
|
|
|
/* Figure the baud rate divisor */
|
|
bdiv = (SB_BASE/kgdb_baud);
|
|
|
|
/* Set the baud rate and LCR values */
|
|
UART_OUT(UART_LCR, (lcr | UART_LCR_DLAB));
|
|
UART_OUT(UART_DLL, (bdiv & 0xff));
|
|
UART_OUT(UART_DLM, ((bdiv >> 8) & 0xff));
|
|
UART_OUT(UART_LCR, lcr);
|
|
|
|
/* Set the MCR */
|
|
UART_OUT(UART_MCR, SB_MCR);
|
|
|
|
/* Turn off FIFOs for now */
|
|
UART_OUT(UART_FCR, 0);
|
|
|
|
/* Setup complete: initialize function pointers */
|
|
kgdb_getchar = kgdb_uart_getchar;
|
|
kgdb_putchar = kgdb_uart_putchar;
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_SH_KGDB */
|
|
|
|
|
|
/*
|
|
* The Machine Vector
|
|
*/
|
|
|
|
struct sh_machine_vector mv_7751se __initmv = {
|
|
.mv_name = "7751 SolutionEngine",
|
|
.mv_setup = sh7751se_setup,
|
|
.mv_nr_irqs = 72,
|
|
|
|
.mv_inb = sh7751se_inb,
|
|
.mv_inw = sh7751se_inw,
|
|
.mv_inl = sh7751se_inl,
|
|
.mv_outb = sh7751se_outb,
|
|
.mv_outw = sh7751se_outw,
|
|
.mv_outl = sh7751se_outl,
|
|
|
|
.mv_inb_p = sh7751se_inb_p,
|
|
.mv_inw_p = sh7751se_inw,
|
|
.mv_inl_p = sh7751se_inl,
|
|
.mv_outb_p = sh7751se_outb_p,
|
|
.mv_outw_p = sh7751se_outw,
|
|
.mv_outl_p = sh7751se_outl,
|
|
|
|
.mv_insl = sh7751se_insl,
|
|
.mv_outsl = sh7751se_outsl,
|
|
|
|
.mv_init_irq = init_7751se_IRQ,
|
|
#ifdef CONFIG_HEARTBEAT
|
|
.mv_heartbeat = heartbeat_7751se,
|
|
#endif
|
|
};
|
|
ALIAS_MV(7751se)
|