1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
108 lines
4.1 KiB
C
108 lines
4.1 KiB
C
/* ------------------------------------------------------------------------- */
|
|
/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c */
|
|
/* ------------------------------------------------------------------------- */
|
|
/* Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd
|
|
* <Peter dot Milne at D hyphen TACQ dot com>
|
|
|
|
This program is free software; you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, version 2.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program; if not, write to the Free Software
|
|
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
|
|
#ifndef I2C_IOP3XX_H
|
|
#define I2C_IOP3XX_H 1
|
|
|
|
/*
|
|
* iop321 hardware bit definitions
|
|
*/
|
|
#define IOP3XX_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */
|
|
#define IOP3XX_ICR_UNIT_RESET 0x4000 /* 1=RESET */
|
|
#define IOP3XX_ICR_SAD_IE 0x2000 /* 1=Slave Detect Interrupt Enable */
|
|
#define IOP3XX_ICR_ALD_IE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */
|
|
#define IOP3XX_ICR_SSD_IE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */
|
|
#define IOP3XX_ICR_BERR_IE 0x0400 /* 1=Bus Error Interrupt Enable */
|
|
#define IOP3XX_ICR_RXFULL_IE 0x0200 /* 1=Receive Full Interrupt Enable */
|
|
#define IOP3XX_ICR_TXEMPTY_IE 0x0100 /* 1=Transmit Empty Interrupt Enable */
|
|
#define IOP3XX_ICR_GCD 0x0080 /* 1=General Call Disable */
|
|
/*
|
|
* IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set
|
|
* when sending a master mode general call message from the I2C unit"
|
|
*/
|
|
#define IOP3XX_ICR_UE 0x0040 /* 1=Unit Enable */
|
|
/*
|
|
* "NOTE: To avoid I2C bus integrity problems,
|
|
* the user needs to ensure that the GPIO Output Data Register -
|
|
* GPOD bits associated with an I2C port are cleared prior to setting
|
|
* the enable bit for that I2C serial port.
|
|
* The user prepares to enable I2C port 0 and
|
|
* I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively.
|
|
*/
|
|
#define IOP3XX_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */
|
|
#define IOP3XX_ICR_MABORT 0x0010 /* 1=Send a STOP with no data
|
|
* NB TBYTE must be clear */
|
|
#define IOP3XX_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */
|
|
#define IOP3XX_ICR_NACK 0x0004 /* 1=reply with NACK */
|
|
#define IOP3XX_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */
|
|
#define IOP3XX_ICR_MSTART 0x0001 /* 1=initiate a START */
|
|
|
|
|
|
#define IOP3XX_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */
|
|
#define IOP3XX_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */
|
|
#define IOP3XX_ISR_GCAD 0x0100 /* 1=General Call Address Detected */
|
|
#define IOP3XX_ISR_RXFULL 0x0080 /* 1=Receive Full */
|
|
#define IOP3XX_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */
|
|
#define IOP3XX_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */
|
|
#define IOP3XX_ISR_SSD 0x0010 /* 1=Slave STOP Detected */
|
|
#define IOP3XX_ISR_BBUSY 0x0008 /* 1=Bus BUSY */
|
|
#define IOP3XX_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */
|
|
#define IOP3XX_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */
|
|
#define IOP3XX_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */
|
|
|
|
#define IOP3XX_ISR_CLEARBITS 0x07f0
|
|
|
|
#define IOP3XX_ISAR_SAMASK 0x007f
|
|
|
|
#define IOP3XX_IDBR_MASK 0x00ff
|
|
|
|
#define IOP3XX_IBMR_SCL 0x0002
|
|
#define IOP3XX_IBMR_SDA 0x0001
|
|
|
|
#define IOP3XX_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */
|
|
#define IOP3XX_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */
|
|
|
|
#define MYSAR 0x02 /* SWAG a suitable slave address */
|
|
|
|
#define I2C_ERR 321
|
|
#define I2C_ERR_BERR (I2C_ERR+0)
|
|
#define I2C_ERR_ALD (I2C_ERR+1)
|
|
|
|
|
|
#define CR_OFFSET 0
|
|
#define SR_OFFSET 0x4
|
|
#define SAR_OFFSET 0x8
|
|
#define DBR_OFFSET 0xc
|
|
#define CCR_OFFSET 0x10
|
|
#define BMR_OFFSET 0x14
|
|
|
|
#define IOP3XX_I2C_IO_SIZE 0x18
|
|
|
|
struct i2c_algo_iop3xx_data {
|
|
u32 ioaddr;
|
|
wait_queue_head_t waitq;
|
|
spinlock_t lock;
|
|
u32 SR_enabled, SR_received;
|
|
int id;
|
|
};
|
|
|
|
#endif /* I2C_IOP3XX_H */
|