android_kernel_xiaomi_sm8350/arch/x86_64/kernel/acpi/wakeup.S
Pavel Machek 343c3f6428 [PATCH] s-t-RAM: load gdt the right way
Sleep code uses wrong version of lgdt, that does the wrong thing when
gdt is beyond 16MB or so.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-25 16:24:32 -07:00

528 lines
11 KiB
ArmAsm

.text
#include <linux/linkage.h>
#include <asm/segment.h>
#include <asm/page.h>
#include <asm/msr.h>
# Copyright 2003 Pavel Machek <pavel@suse.cz>, distribute under GPLv2
#
# wakeup_code runs in real mode, and at unknown address (determined at run-time).
# Therefore it must only use relative jumps/calls.
#
# Do we need to deal with A20? It is okay: ACPI specs says A20 must be enabled
#
# If physical address of wakeup_code is 0x12345, BIOS should call us with
# cs = 0x1234, eip = 0x05
#
ALIGN
.align 16
ENTRY(wakeup_start)
wakeup_code:
wakeup_code_start = .
.code16
# Running in *copy* of this code, somewhere in low 1MB.
movb $0xa1, %al ; outb %al, $0x80
cli
cld
# setup data segment
movw %cs, %ax
movw %ax, %ds # Make ds:0 point to wakeup_start
movw %ax, %ss
mov $(wakeup_stack - wakeup_code), %sp # Private stack is needed for ASUS board
pushl $0 # Kill any dangerous flags
popfl
movl real_magic - wakeup_code, %eax
cmpl $0x12345678, %eax
jne bogus_real_magic
testl $1, video_flags - wakeup_code
jz 1f
lcall $0xc000,$3
movw %cs, %ax
movw %ax, %ds # Bios might have played with that
movw %ax, %ss
1:
testl $2, video_flags - wakeup_code
jz 1f
mov video_mode - wakeup_code, %ax
call mode_seta
1:
movw $0xb800, %ax
movw %ax,%fs
movw $0x0e00 + 'L', %fs:(0x10)
movb $0xa2, %al ; outb %al, $0x80
lidt %ds:idt_48a - wakeup_code
xorl %eax, %eax
movw %ds, %ax # (Convert %ds:gdt to a linear ptr)
shll $4, %eax
addl $(gdta - wakeup_code), %eax
movl %eax, gdt_48a +2 - wakeup_code
lgdtl %ds:gdt_48a - wakeup_code # load gdt with whatever is
# appropriate
movl $1, %eax # protected mode (PE) bit
lmsw %ax # This is it!
jmp 1f
1:
.byte 0x66, 0xea # prefix + jmpi-opcode
.long wakeup_32 - __START_KERNEL_map
.word __KERNEL_CS
.code32
wakeup_32:
# Running in this code, but at low address; paging is not yet turned on.
movb $0xa5, %al ; outb %al, $0x80
/* Check if extended functions are implemented */
movl $0x80000000, %eax
cpuid
cmpl $0x80000000, %eax
jbe bogus_cpu
wbinvd
mov $0x80000001, %eax
cpuid
btl $29, %edx
jnc bogus_cpu
movl %edx,%edi
movw $__KERNEL_DS, %ax
movw %ax, %ds
movw %ax, %es
movw %ax, %fs
movw %ax, %gs
movw $__KERNEL_DS, %ax
movw %ax, %ss
mov $(wakeup_stack - __START_KERNEL_map), %esp
movl saved_magic - __START_KERNEL_map, %eax
cmpl $0x9abcdef0, %eax
jne bogus_32_magic
/*
* Prepare for entering 64bits mode
*/
/* Enable PAE mode and PGE */
xorl %eax, %eax
btsl $5, %eax
btsl $7, %eax
movl %eax, %cr4
/* Setup early boot stage 4 level pagetables */
movl $(wakeup_level4_pgt - __START_KERNEL_map), %eax
movl %eax, %cr3
/* Setup EFER (Extended Feature Enable Register) */
movl $MSR_EFER, %ecx
rdmsr
/* Fool rdmsr and reset %eax to avoid dependences */
xorl %eax, %eax
/* Enable Long Mode */
btsl $_EFER_LME, %eax
/* Enable System Call */
btsl $_EFER_SCE, %eax
/* No Execute supported? */
btl $20,%edi
jnc 1f
btsl $_EFER_NX, %eax
1:
/* Make changes effective */
wrmsr
wbinvd
xorl %eax, %eax
btsl $31, %eax /* Enable paging and in turn activate Long Mode */
btsl $0, %eax /* Enable protected mode */
btsl $1, %eax /* Enable MP */
btsl $4, %eax /* Enable ET */
btsl $5, %eax /* Enable NE */
btsl $16, %eax /* Enable WP */
btsl $18, %eax /* Enable AM */
/* Make changes effective */
movl %eax, %cr0
/* At this point:
CR4.PAE must be 1
CS.L must be 0
CR3 must point to PML4
Next instruction must be a branch
This must be on identity-mapped page
*/
jmp reach_compatibility_mode
reach_compatibility_mode:
movw $0x0e00 + 'i', %ds:(0xb8012)
movb $0xa8, %al ; outb %al, $0x80;
/*
* At this point we're in long mode but in 32bit compatibility mode
* with EFER.LME = 1, CS.L = 0, CS.D = 1 (and in turn
* EFER.LMA = 1). Now we want to jump in 64bit mode, to do that we load
* the new gdt/idt that has __KERNEL_CS with CS.L = 1.
*/
movw $0x0e00 + 'n', %ds:(0xb8014)
movb $0xa9, %al ; outb %al, $0x80
/* Load new GDT with the 64bit segment using 32bit descriptor */
movl $(pGDT32 - __START_KERNEL_map), %eax
lgdt (%eax)
movl $(wakeup_jumpvector - __START_KERNEL_map), %eax
/* Finally jump in 64bit mode */
ljmp *(%eax)
wakeup_jumpvector:
.long wakeup_long64 - __START_KERNEL_map
.word __KERNEL_CS
.code64
/* Hooray, we are in Long 64-bit mode (but still running in low memory) */
wakeup_long64:
/*
* We must switch to a new descriptor in kernel space for the GDT
* because soon the kernel won't have access anymore to the userspace
* addresses where we're currently running on. We have to do that here
* because in 32bit we couldn't load a 64bit linear address.
*/
lgdt cpu_gdt_descr - __START_KERNEL_map
movw $0x0e00 + 'u', %ds:(0xb8016)
nop
nop
movw $__KERNEL_DS, %ax
movw %ax, %ss
movw %ax, %ds
movw %ax, %es
movw %ax, %fs
movw %ax, %gs
movq saved_esp, %rsp
movw $0x0e00 + 'x', %ds:(0xb8018)
movq saved_ebx, %rbx
movq saved_edi, %rdi
movq saved_esi, %rsi
movq saved_ebp, %rbp
movw $0x0e00 + '!', %ds:(0xb801a)
movq saved_eip, %rax
jmp *%rax
.code32
.align 64
gdta:
.word 0, 0, 0, 0 # dummy
.word 0, 0, 0, 0 # unused
.word 0xFFFF # 4Gb - (0x100000*0x1000 = 4Gb)
.word 0 # base address = 0
.word 0x9B00 # code read/exec. ??? Why I need 0x9B00 (as opposed to 0x9A00 in order for this to work?)
.word 0x00CF # granularity = 4096, 386
# (+5th nibble of limit)
.word 0xFFFF # 4Gb - (0x100000*0x1000 = 4Gb)
.word 0 # base address = 0
.word 0x9200 # data read/write
.word 0x00CF # granularity = 4096, 386
# (+5th nibble of limit)
# this is 64bit descriptor for code
.word 0xFFFF
.word 0
.word 0x9A00 # code read/exec
.word 0x00AF # as above, but it is long mode and with D=0
idt_48a:
.word 0 # idt limit = 0
.word 0, 0 # idt base = 0L
gdt_48a:
.word 0x8000 # gdt limit=2048,
# 256 GDT entries
.word 0, 0 # gdt base (filled in later)
real_save_gdt: .word 0
.quad 0
real_magic: .quad 0
video_mode: .quad 0
video_flags: .quad 0
bogus_real_magic:
movb $0xba,%al ; outb %al,$0x80
jmp bogus_real_magic
bogus_32_magic:
movb $0xb3,%al ; outb %al,$0x80
jmp bogus_32_magic
bogus_31_magic:
movb $0xb1,%al ; outb %al,$0x80
jmp bogus_31_magic
bogus_cpu:
movb $0xbc,%al ; outb %al,$0x80
jmp bogus_cpu
/* This code uses an extended set of video mode numbers. These include:
* Aliases for standard modes
* NORMAL_VGA (-1)
* EXTENDED_VGA (-2)
* ASK_VGA (-3)
* Video modes numbered by menu position -- NOT RECOMMENDED because of lack
* of compatibility when extending the table. These are between 0x00 and 0xff.
*/
#define VIDEO_FIRST_MENU 0x0000
/* Standard BIOS video modes (BIOS number + 0x0100) */
#define VIDEO_FIRST_BIOS 0x0100
/* VESA BIOS video modes (VESA number + 0x0200) */
#define VIDEO_FIRST_VESA 0x0200
/* Video7 special modes (BIOS number + 0x0900) */
#define VIDEO_FIRST_V7 0x0900
# Setting of user mode (AX=mode ID) => CF=success
mode_seta:
movw %ax, %bx
#if 0
cmpb $0xff, %ah
jz setalias
testb $VIDEO_RECALC>>8, %ah
jnz _setrec
cmpb $VIDEO_FIRST_RESOLUTION>>8, %ah
jnc setres
cmpb $VIDEO_FIRST_SPECIAL>>8, %ah
jz setspc
cmpb $VIDEO_FIRST_V7>>8, %ah
jz setv7
#endif
cmpb $VIDEO_FIRST_VESA>>8, %ah
jnc check_vesaa
#if 0
orb %ah, %ah
jz setmenu
#endif
decb %ah
# jz setbios Add bios modes later
setbada: clc
ret
check_vesaa:
subb $VIDEO_FIRST_VESA>>8, %bh
orw $0x4000, %bx # Use linear frame buffer
movw $0x4f02, %ax # VESA BIOS mode set call
int $0x10
cmpw $0x004f, %ax # AL=4f if implemented
jnz _setbada # AH=0 if OK
stc
ret
_setbada: jmp setbada
.code64
bogus_magic:
movw $0x0e00 + 'B', %ds:(0xb8018)
jmp bogus_magic
bogus_magic2:
movw $0x0e00 + '2', %ds:(0xb8018)
jmp bogus_magic2
wakeup_stack_begin: # Stack grows down
.org 0xff0
wakeup_stack: # Just below end of page
ENTRY(wakeup_end)
##
# acpi_copy_wakeup_routine
#
# Copy the above routine to low memory.
#
# Parameters:
# %rdi: place to copy wakeup routine to
#
# Returned address is location of code in low memory (past data and stack)
#
ENTRY(acpi_copy_wakeup_routine)
pushq %rax
pushq %rcx
pushq %rdx
sgdt saved_gdt
sidt saved_idt
sldt saved_ldt
str saved_tss
movq %cr3, %rdx
movq %rdx, saved_cr3
movq %cr4, %rdx
movq %rdx, saved_cr4
movq %cr0, %rdx
movq %rdx, saved_cr0
sgdt real_save_gdt - wakeup_start (,%rdi)
movl $MSR_EFER, %ecx
rdmsr
movl %eax, saved_efer
movl %edx, saved_efer2
movl saved_video_mode, %edx
movl %edx, video_mode - wakeup_start (,%rdi)
movl acpi_video_flags, %edx
movl %edx, video_flags - wakeup_start (,%rdi)
movq $0x12345678, real_magic - wakeup_start (,%rdi)
movq $0x123456789abcdef0, %rdx
movq %rdx, saved_magic
movl saved_magic - __START_KERNEL_map, %eax
cmpl $0x9abcdef0, %eax
jne bogus_32_magic
# make sure %cr4 is set correctly (features, etc)
movl saved_cr4 - __START_KERNEL_map, %eax
movq %rax, %cr4
movl saved_cr0 - __START_KERNEL_map, %eax
movq %rax, %cr0
jmp 1f # Flush pipelines
1:
# restore the regs we used
popq %rdx
popq %rcx
popq %rax
ENTRY(do_suspend_lowlevel_s4bios)
ret
.align 2
.p2align 4,,15
.globl do_suspend_lowlevel
.type do_suspend_lowlevel,@function
do_suspend_lowlevel:
.LFB5:
subq $8, %rsp
xorl %eax, %eax
call save_processor_state
movq %rsp, saved_context_esp(%rip)
movq %rax, saved_context_eax(%rip)
movq %rbx, saved_context_ebx(%rip)
movq %rcx, saved_context_ecx(%rip)
movq %rdx, saved_context_edx(%rip)
movq %rbp, saved_context_ebp(%rip)
movq %rsi, saved_context_esi(%rip)
movq %rdi, saved_context_edi(%rip)
movq %r8, saved_context_r08(%rip)
movq %r9, saved_context_r09(%rip)
movq %r10, saved_context_r10(%rip)
movq %r11, saved_context_r11(%rip)
movq %r12, saved_context_r12(%rip)
movq %r13, saved_context_r13(%rip)
movq %r14, saved_context_r14(%rip)
movq %r15, saved_context_r15(%rip)
pushfq ; popq saved_context_eflags(%rip)
movq $.L97, saved_eip(%rip)
movq %rsp,saved_esp
movq %rbp,saved_ebp
movq %rbx,saved_ebx
movq %rdi,saved_edi
movq %rsi,saved_esi
addq $8, %rsp
movl $3, %edi
xorl %eax, %eax
jmp acpi_enter_sleep_state
.L97:
.p2align 4,,7
.L99:
.align 4
movl $24, %eax
movw %ax, %ds
movq saved_context+58(%rip), %rax
movq %rax, %cr4
movq saved_context+50(%rip), %rax
movq %rax, %cr3
movq saved_context+42(%rip), %rax
movq %rax, %cr2
movq saved_context+34(%rip), %rax
movq %rax, %cr0
pushq saved_context_eflags(%rip) ; popfq
movq saved_context_esp(%rip), %rsp
movq saved_context_ebp(%rip), %rbp
movq saved_context_eax(%rip), %rax
movq saved_context_ebx(%rip), %rbx
movq saved_context_ecx(%rip), %rcx
movq saved_context_edx(%rip), %rdx
movq saved_context_esi(%rip), %rsi
movq saved_context_edi(%rip), %rdi
movq saved_context_r08(%rip), %r8
movq saved_context_r09(%rip), %r9
movq saved_context_r10(%rip), %r10
movq saved_context_r11(%rip), %r11
movq saved_context_r12(%rip), %r12
movq saved_context_r13(%rip), %r13
movq saved_context_r14(%rip), %r14
movq saved_context_r15(%rip), %r15
xorl %eax, %eax
addq $8, %rsp
jmp restore_processor_state
.LFE5:
.Lfe5:
.size do_suspend_lowlevel,.Lfe5-do_suspend_lowlevel
.data
ALIGN
ENTRY(saved_ebp) .quad 0
ENTRY(saved_esi) .quad 0
ENTRY(saved_edi) .quad 0
ENTRY(saved_ebx) .quad 0
ENTRY(saved_eip) .quad 0
ENTRY(saved_esp) .quad 0
ENTRY(saved_magic) .quad 0
ALIGN
# saved registers
saved_gdt: .quad 0,0
saved_idt: .quad 0,0
saved_ldt: .quad 0
saved_tss: .quad 0
saved_cr0: .quad 0
saved_cr3: .quad 0
saved_cr4: .quad 0
saved_efer: .quad 0
saved_efer2: .quad 0