android_kernel_xiaomi_sm8350/drivers/scsi/st_options.h
Kai Makisara 40f6b36c62 [SCSI] st: add option to use SILI in variable block reads
Add new option MT_ST_SILI to enable setting the SILI bit in reads in variable
block mode. If SILI is set, reading a block shorter than the byte count does
not result in CHECK CONDITION. The length of the block is determined using the
residual count from the HBA. Avoiding the REQUEST SENSE command for every
block speeds up some real applications considerably.

Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-07 12:15:39 -05:00

105 lines
3.9 KiB
C

/*
The compile-time configurable defaults for the Linux SCSI tape driver.
Copyright 1995-2003 Kai Makisara.
Last modified: Thu Feb 21 21:47:07 2008 by kai.makisara
*/
#ifndef _ST_OPTIONS_H
#define _ST_OPTIONS_H
/* If TRY_DIRECT_IO is non-zero, the driver tries to transfer data directly
between the user buffer and tape drive. If this is not possible, driver
buffer is used. If TRY_DIRECT_IO is zero, driver buffer is always used. */
#define TRY_DIRECT_IO 1
/* The driver does not wait for some operations to finish before returning
to the user program if ST_NOWAIT is non-zero. This helps if the SCSI
adapter does not support multiple outstanding commands. However, the user
should not give a new tape command before the previous one has finished. */
#define ST_NOWAIT 0
/* If ST_IN_FILE_POS is nonzero, the driver positions the tape after the
record been read by the user program even if the tape has moved further
because of buffered reads. Should be set to zero to support also drives
that can't space backwards over records. NOTE: The tape will be
spaced backwards over an "accidentally" crossed filemark in any case. */
#define ST_IN_FILE_POS 0
/* If ST_RECOVERED_WRITE_FATAL is non-zero, recovered errors while writing
are considered "hard errors". */
#define ST_RECOVERED_WRITE_FATAL 0
/* The "guess" for the block size for devices that don't support MODE
SENSE. */
#define ST_DEFAULT_BLOCK 0
/* The minimum tape driver buffer size in kilobytes in fixed block mode.
Must be non-zero. */
#define ST_FIXED_BUFFER_BLOCKS 32
/* Maximum number of scatter/gather segments */
#define ST_MAX_SG 256
/* The number of scatter/gather segments to allocate at first try (must be
smaller or equal to the maximum). */
#define ST_FIRST_SG 8
/* The size of the first scatter/gather segments (determines the maximum block
size for SCSI adapters not supporting scatter/gather). The default is set
to try to allocate the buffer as one chunk. */
#define ST_FIRST_ORDER 5
/* The following lines define defaults for properties that can be set
separately for each drive using the MTSTOPTIONS ioctl. */
/* If ST_TWO_FM is non-zero, the driver writes two filemarks after a
file being written. Some drives can't handle two filemarks at the
end of data. */
#define ST_TWO_FM 0
/* If ST_BUFFER_WRITES is non-zero, writes in fixed block mode are
buffered until the driver buffer is full or asynchronous write is
triggered. May make detection of End-Of-Medium early enough fail. */
#define ST_BUFFER_WRITES 1
/* If ST_ASYNC_WRITES is non-zero, the SCSI write command may be started
without waiting for it to finish. May cause problems in multiple
tape backups. */
#define ST_ASYNC_WRITES 1
/* If ST_READ_AHEAD is non-zero, blocks are read ahead in fixed block
mode. */
#define ST_READ_AHEAD 1
/* If ST_AUTO_LOCK is non-zero, the drive door is locked at the first
read or write command after the device is opened. The door is opened
when the device is closed. */
#define ST_AUTO_LOCK 0
/* If ST_FAST_MTEOM is non-zero, the MTEOM ioctl is done using the
direct SCSI command. The file number status is lost but this method
is fast with some drives. Otherwise MTEOM is done by spacing over
files and the file number status is retained. */
#define ST_FAST_MTEOM 0
/* If ST_SCSI2LOGICAL is nonzero, the logical block addresses are used for
MTIOCPOS and MTSEEK by default. Vendor addresses are used if ST_SCSI2LOGICAL
is zero. */
#define ST_SCSI2LOGICAL 0
/* If ST_SYSV is non-zero, the tape behaves according to the SYS V semantics.
The default is BSD semantics. */
#define ST_SYSV 0
/* If ST_SILI is non-zero, the SILI bit is set when reading in variable block
mode and the block size is determined using the residual returned by the HBA. */
#define ST_SILI 0
/* Time to wait for the drive to become ready if blocking open */
#define ST_BLOCK_SECONDS 120
#endif