230d42d422
Each SPI controller has exactly one CS line and as such doesn't provide for multi-cs. We implement a workaround to support multi-cs by _not_ configuring the mux'ed CS pin for each SPI controller. The CS mechanism is assumed to be fully machine specific - the driver doesn't even assume some GPIO pin is used to control the CS. The driver selects between DMA and POLLING mode depending upon the xfer size - DMA mode for xfers bigger than FIFO size, POLLING mode otherwise. The driver has been designed to be capable of running SoCs since s3c64xx and till date, for that reason some of the register fields have been passed via, SoC specific, platform data. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
62 lines
2.1 KiB
Makefile
62 lines
2.1 KiB
Makefile
#
|
|
# Makefile for kernel SPI drivers.
|
|
#
|
|
|
|
ifeq ($(CONFIG_SPI_DEBUG),y)
|
|
EXTRA_CFLAGS += -DDEBUG
|
|
endif
|
|
|
|
# small core, mostly translating board-specific
|
|
# config declarations into driver model code
|
|
obj-$(CONFIG_SPI_MASTER) += spi.o
|
|
|
|
# SPI master controller drivers (bus)
|
|
obj-$(CONFIG_SPI_ATMEL) += atmel_spi.o
|
|
obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
|
|
obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
|
|
obj-$(CONFIG_SPI_AU1550) += au1550_spi.o
|
|
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
|
|
obj-$(CONFIG_SPI_DESIGNWARE) += dw_spi.o
|
|
obj-$(CONFIG_SPI_DW_PCI) += dw_spi_pci.o
|
|
obj-$(CONFIG_SPI_GPIO) += spi_gpio.o
|
|
obj-$(CONFIG_SPI_IMX) += spi_imx.o
|
|
obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o
|
|
obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
|
|
obj-$(CONFIG_SPI_OMAP_UWIRE) += omap_uwire.o
|
|
obj-$(CONFIG_SPI_OMAP24XX) += omap2_mcspi.o
|
|
obj-$(CONFIG_SPI_OMAP_100K) += omap_spi_100k.o
|
|
obj-$(CONFIG_SPI_ORION) += orion_spi.o
|
|
obj-$(CONFIG_SPI_PL022) += amba-pl022.o
|
|
obj-$(CONFIG_SPI_MPC52xx_PSC) += mpc52xx_psc_spi.o
|
|
obj-$(CONFIG_SPI_MPC52xx) += mpc52xx_spi.o
|
|
obj-$(CONFIG_SPI_MPC8xxx) += spi_mpc8xxx.o
|
|
obj-$(CONFIG_SPI_PPC4xx) += spi_ppc4xx.o
|
|
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
|
|
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o
|
|
obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o
|
|
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
|
|
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
|
|
obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o
|
|
obj-$(CONFIG_SPI_XILINX_PLTFM) += xilinx_spi_pltfm.o
|
|
obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o
|
|
obj-$(CONFIG_SPI_SH_MSIOF) += spi_sh_msiof.o
|
|
obj-$(CONFIG_SPI_STMP3XXX) += spi_stmp.o
|
|
obj-$(CONFIG_SPI_NUC900) += spi_nuc900.o
|
|
|
|
# special build for s3c24xx spi driver with fiq support
|
|
spi_s3c24xx_hw-y := spi_s3c24xx.o
|
|
spi_s3c24xx_hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi_s3c24xx_fiq.o
|
|
|
|
# ... add above this line ...
|
|
|
|
# SPI protocol drivers (device/link on bus)
|
|
obj-$(CONFIG_SPI_SPIDEV) += spidev.o
|
|
obj-$(CONFIG_SPI_TLE62X0) += tle62x0.o
|
|
# ... add above this line ...
|
|
|
|
# SPI slave controller drivers (upstream link)
|
|
# ... add above this line ...
|
|
|
|
# SPI slave drivers (protocol for that link)
|
|
# ... add above this line ...
|