6a304caf0b
For some SDVO cards based on conexant chip, we can't read the EDID if we don't read the response after issuing SDVO DDC bus switch command. From the SDVO spec once when another I2C transaction is finished after completing the I2C transaction of issuing the bus switch command, it will be switched back to the SDVO internal state again. So we can't initiate a new I2C transaction to read the response after issuing the DDC bus switch command. Instead we should issue DDC bus switch command and read the response in the same I2C transaction. https://bugs.freedesktop.org/show_bug.cgi?id=23842 https://bugs.freedesktop.org/show_bug.cgi?id=24458 https://bugs.freedesktop.org/show_bug.cgi?id=24522 https://bugs.freedesktop.org/show_bug.cgi?id=24282 Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca> Signed-off-by: Eric Anholt <eric@anholt.net> |
||
|---|---|---|
| .. | ||
| i2c | ||
| i810 | ||
| i830 | ||
| i915 | ||
| mga | ||
| nouveau | ||
| r128 | ||
| radeon | ||
| savage | ||
| sis | ||
| tdfx | ||
| ttm | ||
| via | ||
| vmwgfx | ||
| ati_pcigart.c | ||
| drm_agpsupport.c | ||
| drm_auth.c | ||
| drm_bufs.c | ||
| drm_cache.c | ||
| drm_context.c | ||
| drm_crtc_helper.c | ||
| drm_crtc.c | ||
| drm_debugfs.c | ||
| drm_dma.c | ||
| drm_dp_i2c_helper.c | ||
| drm_drawable.c | ||
| drm_drv.c | ||
| drm_edid.c | ||
| drm_encoder_slave.c | ||
| drm_fb_helper.c | ||
| drm_fops.c | ||
| drm_gem.c | ||
| drm_hashtab.c | ||
| drm_info.c | ||
| drm_ioc32.c | ||
| drm_ioctl.c | ||
| drm_irq.c | ||
| drm_lock.c | ||
| drm_memory.c | ||
| drm_mm.c | ||
| drm_modes.c | ||
| drm_pci.c | ||
| drm_proc.c | ||
| drm_scatter.c | ||
| drm_sman.c | ||
| drm_stub.c | ||
| drm_sysfs.c | ||
| drm_vm.c | ||
| Kconfig | ||
| Makefile | ||
| README.drm | ||
************************************************************
* For the very latest on DRI development, please see: *
* http://dri.freedesktop.org/ *
************************************************************
The Direct Rendering Manager (drm) is a device-independent kernel-level
device driver that provides support for the XFree86 Direct Rendering
Infrastructure (DRI).
The DRM supports the Direct Rendering Infrastructure (DRI) in four major
ways:
1. The DRM provides synchronized access to the graphics hardware via
the use of an optimized two-tiered lock.
2. The DRM enforces the DRI security policy for access to the graphics
hardware by only allowing authenticated X11 clients access to
restricted regions of memory.
3. The DRM provides a generic DMA engine, complete with multiple
queues and the ability to detect the need for an OpenGL context
switch.
4. The DRM is extensible via the use of small device-specific modules
that rely extensively on the API exported by the DRM module.
Documentation on the DRI is available from:
http://dri.freedesktop.org/wiki/Documentation
http://sourceforge.net/project/showfiles.php?group_id=387
http://dri.sourceforge.net/doc/
For specific information about kernel-level support, see:
The Direct Rendering Manager, Kernel Support for the Direct Rendering
Infrastructure
http://dri.sourceforge.net/doc/drm_low_level.html
Hardware Locking for the Direct Rendering Infrastructure
http://dri.sourceforge.net/doc/hardware_locking_low_level.html
A Security Analysis of the Direct Rendering Infrastructure
http://dri.sourceforge.net/doc/security_low_level.html