b446197cc1
This patch finishes the port and enables debug as an build option.
This was tested on:
Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
RF5112A multiband radio found (0x36)
Note:
For 2 GHz band on the above card I noticed we get negative channel
numbers. Will look into this unless someone beats me to it.
Example out put when loading using:
sudo modprobe ath5k debug=0x00000400
Band 2 GHz: channels 26, rates 12
channels:
1 2412 00c0 0000
2 2417 00c0 0000
3 2422 00c0 0000
4 2427 00c0 0000
5 2432 00c0 0000
6 2437 00c0 0000
7 2442 00c0 0000
8 2447 00c0 0000
9 2452 00c0 0000
10 2457 00c0 0000
11 2462 00c0 0000
12 2467 00c0 0000
13 2472 00c0 0000
14 2484 00c0 0000
-498 2512 00c0 0000
-494 2532 00c0 0000
-490 2552 00c0 0000
-486 2572 00c0 0000
-482 2592 00c0 0000
-478 2612 00c0 0000
-474 2632 00c0 0000
-470 2652 00c0 0000
-466 2672 00c0 0000
-462 2692 00c0 0000
-458 2712 00c0 0000
-454 2732 00c0 0000
Band 5 GHz: channels 194, rates 8
channels:
27 5135 0140 0000
28 5140 0140 0000
[... etc ]
219 6095 0140 0000
220 6100 0140 0000
rates:
60 000b 0000 0000
90 000f 0000 0000
120 000a 0000 0000
180 000e 0000 0000
240 0009 0000 0000
360 000d 0000 0000
480 0008 0000 0000
540 000c 0000 0000
Changes to base.c, base.h
Changes-licensed-under: 3-Clause-BSD
Changes to debug.c, debug.h
Changes-licensed-under: GPL
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
38 lines
929 B
Plaintext
38 lines
929 B
Plaintext
config ATH5K
|
|
tristate "Atheros 5xxx wireless cards support"
|
|
depends on PCI && MAC80211 && WLAN_80211 && EXPERIMENTAL
|
|
---help---
|
|
This module adds support for wireless adapters based on
|
|
Atheros 5xxx chipset.
|
|
|
|
Currently the following chip versions are supported:
|
|
|
|
MAC: AR5211 AR5212
|
|
PHY: RF5111/2111 RF5112/2112 RF5413/2413
|
|
|
|
This driver uses the kernel's mac80211 subsystem.
|
|
|
|
If you choose to build a module, it'll be called ath5k. Say M if
|
|
unsure.
|
|
|
|
config ATH5K_DEBUG
|
|
bool "Atheros 5xxx debugging"
|
|
depends on ATH5K
|
|
---help---
|
|
Atheros 5xxx debugging messages.
|
|
|
|
Say Y, if and you will get debug options for ath5k.
|
|
To use this, you need to mount debugfs:
|
|
|
|
mkdir /debug/
|
|
mount -t debugfs debug /debug/
|
|
|
|
You will get access to files under:
|
|
/debug/ath5k/phy0/
|
|
|
|
To enable debug, pass the debug level to the debug module
|
|
parameter. For example:
|
|
|
|
modprobe ath5k debug=0x00000400
|
|
|