android_kernel_xiaomi_sm8350/Documentation/networking/vxge.txt
Ramkrishna Vepa 5adfb64bdd Neterion: Driver help file
- vxge driver help text file.

- No change from previous submission.

- Changes in previous submissions -
  Removed the performance tuning section with instructions to disable
  time stamps and change sysctl settings - Reported by Dave Miller
  General clean up.
 - Removed tx/rx_pause, exec_mode, tx_steering_type, rx_steering_type, gro,
   intr_type, rx & tx max_indicate_pkts and exec_mode loadable parameters. The
   driver default settings work well in most if not all cases. Another patch
   to configure these parameters with ethtool will be released in the future -
   Reported by Stephen Hemminger.
- Incorporated following fixes based on comments from Ben Hutchings
        Removed references to earlier kernel versions.
        Removed sections that are similar for all drivers -
                Load/Unload
                Identifying the adapter/interface
                Boot time configuration
        Removed loadable parameter -
                NAPI - Napi is always enabled.
                rx_steering_type & ring_blocks - The driver default settings
                work well in most if not all cases. Another patch to configure
                these parameters with ethtool will be released in the future.
        Removed ethtool support section - No need to duplicate ethtool
                docs here.
        Removed Known Issue on SUSE 9 - Doesn't apply when using a
                current kernel.
        Removed Common Problems section - These don't apply to in-tree modules.
        Removed Available Downloads section - Not sure this belongs in-tree.
        Removed Copyright information - This notice doesn't belong in
                the kernel.

Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 00:33:39 -07:00

101 lines
3.1 KiB
Plaintext

Neterion's (Formerly S2io) X3100 Series 10GbE PCIe Server Adapter Linux driver
==============================================================================
Contents
--------
1) Introduction
2) Features supported
3) Configurable driver parameters
4) Troubleshooting
1) Introduction:
----------------
This Linux driver supports all Neterion's X3100 series 10 GbE PCIe I/O
Virtualized Server adapters.
The X3100 series supports four modes of operation, configurable via
firmware -
Single function mode
Multi function mode
SRIOV mode
MRIOV mode
The functions share a 10GbE link and the pci-e bus, but hardly anything else
inside the ASIC. Features like independent hw reset, statistics, bandwidth/
priority allocation and guarantees, GRO, TSO, interrupt moderation etc are
supported independently on each function.
(See below for a complete list of features supported for both IPv4 and IPv6)
2) Features supported:
----------------------
i) Single function mode (up to 17 queues)
ii) Multi function mode (up to 17 functions)
iii) PCI-SIG's I/O Virtualization
- Single Root mode: v1.0 (up to 17 functions)
- Multi-Root mode: v1.0 (up to 17 functions)
iv) Jumbo frames
X3100 Series supports MTU up to 9600 bytes, modifiable using
ifconfig command.
v) Offloads supported: (Enabled by default)
Checksum offload (TCP/UDP/IP) on transmit and receive paths
TCP Segmentation Offload (TSO) on transmit path
Generic Receive Offload (GRO) on receive path
vi) MSI-X: (Enabled by default)
Resulting in noticeable performance improvement (up to 7% on certain
platforms).
vii) NAPI: (Enabled by default)
For better Rx interrupt moderation.
viii)RTH (Receive Traffic Hash): (Enabled by default)
Receive side steering for better scaling.
ix) Statistics
Comprehensive MAC-level and software statistics displayed using
"ethtool -S" option.
x) Multiple hardware queues: (Enabled by default)
Up to 17 hardware based transmit and receive data channels, with
multiple steering options (transmit multiqueue enabled by default).
3) Configurable driver parameters:
----------------------------------
i) max_config_dev
Specifies maximum device functions to be enabled.
Valid range: 1-8
ii) max_config_port
Specifies number of ports to be enabled.
Valid range: 1,2
Default: 1
iii)max_config_vpath
Specifies maximum VPATH(s) configured for each device function.
Valid range: 1-17
iv) vlan_tag_strip
Enables/disables vlan tag stripping from all received tagged frames that
are not replicated at the internal L2 switch.
Valid range: 0,1 (disabled, enabled respectively)
Default: 1
v) addr_learn_en
Enable learning the mac address of the guest OS interface in
virtualization environment.
Valid range: 0,1 (disabled, enabled respectively)
Default: 0
4) Troubleshooting:
-------------------
To resolve an issue with the source code or X3100 series adapter, please collect
the statistics, register dumps using ethool, relevant logs and email them to
support@neterion.com.