75f2d3eac9
The 10Xpress PHY supports flash upgrades through MDIO, but needs to be put in upgrade mode at power-up. This adds a module parameter and other logic to support that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
267 lines
7.1 KiB
C
267 lines
7.1 KiB
C
/****************************************************************************
|
|
* Driver for Solarflare Solarstorm network controllers and boards
|
|
* Copyright 2007 Solarflare Communications Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License version 2 as published
|
|
* by the Free Software Foundation, incorporated herein by reference.
|
|
*/
|
|
|
|
/*****************************************************************************
|
|
* Support for the SFE4001 NIC: driver code for the PCA9539 I/O expander that
|
|
* controls the PHY power rails, and for the MAX6647 temp. sensor used to check
|
|
* the PHY
|
|
*/
|
|
#include <linux/delay.h>
|
|
#include "efx.h"
|
|
#include "phy.h"
|
|
#include "boards.h"
|
|
#include "falcon.h"
|
|
#include "falcon_hwdefs.h"
|
|
#include "mac.h"
|
|
|
|
/**************************************************************************
|
|
*
|
|
* I2C IO Expander device
|
|
*
|
|
**************************************************************************/
|
|
#define PCA9539 0x74
|
|
|
|
#define P0_IN 0x00
|
|
#define P0_OUT 0x02
|
|
#define P0_INVERT 0x04
|
|
#define P0_CONFIG 0x06
|
|
|
|
#define P0_EN_1V0X_LBN 0
|
|
#define P0_EN_1V0X_WIDTH 1
|
|
#define P0_EN_1V2_LBN 1
|
|
#define P0_EN_1V2_WIDTH 1
|
|
#define P0_EN_2V5_LBN 2
|
|
#define P0_EN_2V5_WIDTH 1
|
|
#define P0_EN_3V3X_LBN 3
|
|
#define P0_EN_3V3X_WIDTH 1
|
|
#define P0_EN_5V_LBN 4
|
|
#define P0_EN_5V_WIDTH 1
|
|
#define P0_SHORTEN_JTAG_LBN 5
|
|
#define P0_SHORTEN_JTAG_WIDTH 1
|
|
#define P0_X_TRST_LBN 6
|
|
#define P0_X_TRST_WIDTH 1
|
|
#define P0_DSP_RESET_LBN 7
|
|
#define P0_DSP_RESET_WIDTH 1
|
|
|
|
#define P1_IN 0x01
|
|
#define P1_OUT 0x03
|
|
#define P1_INVERT 0x05
|
|
#define P1_CONFIG 0x07
|
|
|
|
#define P1_AFE_PWD_LBN 0
|
|
#define P1_AFE_PWD_WIDTH 1
|
|
#define P1_DSP_PWD25_LBN 1
|
|
#define P1_DSP_PWD25_WIDTH 1
|
|
#define P1_RESERVED_LBN 2
|
|
#define P1_RESERVED_WIDTH 2
|
|
#define P1_SPARE_LBN 4
|
|
#define P1_SPARE_WIDTH 4
|
|
|
|
|
|
/**************************************************************************
|
|
*
|
|
* Temperature Sensor
|
|
*
|
|
**************************************************************************/
|
|
#define MAX6647 0x4e
|
|
|
|
#define RLTS 0x00
|
|
#define RLTE 0x01
|
|
#define RSL 0x02
|
|
#define RCL 0x03
|
|
#define RCRA 0x04
|
|
#define RLHN 0x05
|
|
#define RLLI 0x06
|
|
#define RRHI 0x07
|
|
#define RRLS 0x08
|
|
#define WCRW 0x0a
|
|
#define WLHO 0x0b
|
|
#define WRHA 0x0c
|
|
#define WRLN 0x0e
|
|
#define OSHT 0x0f
|
|
#define REET 0x10
|
|
#define RIET 0x11
|
|
#define RWOE 0x19
|
|
#define RWOI 0x20
|
|
#define HYS 0x21
|
|
#define QUEUE 0x22
|
|
#define MFID 0xfe
|
|
#define REVID 0xff
|
|
|
|
/* Status bits */
|
|
#define MAX6647_BUSY (1 << 7) /* ADC is converting */
|
|
#define MAX6647_LHIGH (1 << 6) /* Local high temp. alarm */
|
|
#define MAX6647_LLOW (1 << 5) /* Local low temp. alarm */
|
|
#define MAX6647_RHIGH (1 << 4) /* Remote high temp. alarm */
|
|
#define MAX6647_RLOW (1 << 3) /* Remote low temp. alarm */
|
|
#define MAX6647_FAULT (1 << 2) /* DXN/DXP short/open circuit */
|
|
#define MAX6647_EOT (1 << 1) /* Remote junction overtemp. */
|
|
#define MAX6647_IOT (1 << 0) /* Local junction overtemp. */
|
|
|
|
static const u8 xgphy_max_temperature = 90;
|
|
|
|
void sfe4001_poweroff(struct efx_nic *efx)
|
|
{
|
|
struct efx_i2c_interface *i2c = &efx->i2c;
|
|
|
|
u8 cfg, out, in;
|
|
|
|
EFX_INFO(efx, "%s\n", __func__);
|
|
|
|
/* Turn off all power rails */
|
|
out = 0xff;
|
|
(void) efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
|
|
|
|
/* Disable port 1 outputs on IO expander */
|
|
cfg = 0xff;
|
|
(void) efx_i2c_write(i2c, PCA9539, P1_CONFIG, &cfg, 1);
|
|
|
|
/* Disable port 0 outputs on IO expander */
|
|
cfg = 0xff;
|
|
(void) efx_i2c_write(i2c, PCA9539, P0_CONFIG, &cfg, 1);
|
|
|
|
/* Clear any over-temperature alert */
|
|
(void) efx_i2c_read(i2c, MAX6647, RSL, &in, 1);
|
|
}
|
|
|
|
/* The P0_EN_3V3X line on SFE4001 boards (from A2 onward) is connected
|
|
* to the FLASH_CFG_1 input on the DSP. We must keep it high at power-
|
|
* up to allow writing the flash (done through MDIO from userland).
|
|
*/
|
|
unsigned int sfe4001_phy_flash_cfg;
|
|
module_param_named(phy_flash_cfg, sfe4001_phy_flash_cfg, uint, 0444);
|
|
MODULE_PARM_DESC(phy_flash_cfg,
|
|
"Force PHY to enter flash configuration mode");
|
|
|
|
/* This board uses an I2C expander to provider power to the PHY, which needs to
|
|
* be turned on before the PHY can be used.
|
|
* Context: Process context, rtnl lock held
|
|
*/
|
|
int sfe4001_poweron(struct efx_nic *efx)
|
|
{
|
|
struct efx_i2c_interface *i2c = &efx->i2c;
|
|
unsigned int count;
|
|
int rc;
|
|
u8 out, in, cfg;
|
|
efx_dword_t reg;
|
|
|
|
/* 10Xpress has fixed-function LED pins, so there is no board-specific
|
|
* blink code. */
|
|
efx->board_info.blink = tenxpress_phy_blink;
|
|
|
|
/* Ensure that XGXS and XAUI SerDes are held in reset */
|
|
EFX_POPULATE_DWORD_7(reg, XX_PWRDNA_EN, 1,
|
|
XX_PWRDNB_EN, 1,
|
|
XX_RSTPLLAB_EN, 1,
|
|
XX_RESETA_EN, 1,
|
|
XX_RESETB_EN, 1,
|
|
XX_RSTXGXSRX_EN, 1,
|
|
XX_RSTXGXSTX_EN, 1);
|
|
falcon_xmac_writel(efx, ®, XX_PWR_RST_REG_MAC);
|
|
udelay(10);
|
|
|
|
/* Set DSP over-temperature alert threshold */
|
|
EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature);
|
|
rc = efx_i2c_write(i2c, MAX6647, WLHO,
|
|
&xgphy_max_temperature, 1);
|
|
if (rc)
|
|
goto fail1;
|
|
|
|
/* Read it back and verify */
|
|
rc = efx_i2c_read(i2c, MAX6647, RLHN, &in, 1);
|
|
if (rc)
|
|
goto fail1;
|
|
if (in != xgphy_max_temperature) {
|
|
rc = -EFAULT;
|
|
goto fail1;
|
|
}
|
|
|
|
/* Clear any previous over-temperature alert */
|
|
rc = efx_i2c_read(i2c, MAX6647, RSL, &in, 1);
|
|
if (rc)
|
|
goto fail1;
|
|
|
|
/* Enable port 0 and port 1 outputs on IO expander */
|
|
cfg = 0x00;
|
|
rc = efx_i2c_write(i2c, PCA9539, P0_CONFIG, &cfg, 1);
|
|
if (rc)
|
|
goto fail1;
|
|
cfg = 0xff & ~(1 << P1_SPARE_LBN);
|
|
rc = efx_i2c_write(i2c, PCA9539, P1_CONFIG, &cfg, 1);
|
|
if (rc)
|
|
goto fail2;
|
|
|
|
/* Turn all power off then wait 1 sec. This ensures PHY is reset */
|
|
out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
|
|
(0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
|
|
(0 << P0_EN_1V0X_LBN));
|
|
rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
|
|
if (rc)
|
|
goto fail3;
|
|
|
|
schedule_timeout_uninterruptible(HZ);
|
|
count = 0;
|
|
do {
|
|
/* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */
|
|
out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
|
|
(1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
|
|
(1 << P0_X_TRST_LBN));
|
|
if (sfe4001_phy_flash_cfg)
|
|
out |= 1 << P0_EN_3V3X_LBN;
|
|
|
|
rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
|
|
if (rc)
|
|
goto fail3;
|
|
msleep(10);
|
|
|
|
/* Turn on 1V power rail */
|
|
out &= ~(1 << P0_EN_1V0X_LBN);
|
|
rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
|
|
if (rc)
|
|
goto fail3;
|
|
|
|
EFX_INFO(efx, "waiting for power (attempt %d)...\n", count);
|
|
|
|
schedule_timeout_uninterruptible(HZ);
|
|
|
|
/* Check DSP is powered */
|
|
rc = efx_i2c_read(i2c, PCA9539, P1_IN, &in, 1);
|
|
if (rc)
|
|
goto fail3;
|
|
if (in & (1 << P1_AFE_PWD_LBN))
|
|
goto done;
|
|
|
|
/* DSP doesn't look powered in flash config mode */
|
|
if (sfe4001_phy_flash_cfg)
|
|
goto done;
|
|
} while (++count < 20);
|
|
|
|
EFX_INFO(efx, "timed out waiting for power\n");
|
|
rc = -ETIMEDOUT;
|
|
goto fail3;
|
|
|
|
done:
|
|
EFX_INFO(efx, "PHY is powered on\n");
|
|
return 0;
|
|
|
|
fail3:
|
|
/* Turn off all power rails */
|
|
out = 0xff;
|
|
(void) efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
|
|
/* Disable port 1 outputs on IO expander */
|
|
out = 0xff;
|
|
(void) efx_i2c_write(i2c, PCA9539, P1_CONFIG, &out, 1);
|
|
fail2:
|
|
/* Disable port 0 outputs on IO expander */
|
|
out = 0xff;
|
|
(void) efx_i2c_write(i2c, PCA9539, P0_CONFIG, &out, 1);
|
|
fail1:
|
|
return rc;
|
|
}
|