android_kernel_xiaomi_sm8350/arch/cris/arch-v32/Kconfig
Jesper Nilsson 923dd2a463 CRIS: Rearrange Kconfigs for v10 and v32 to allow compilation without warnings.
- Remove some unneeded configs and add some new ones.
- Merge common config items to common file instead of duplicating them.
- Pull in standard Kconfig.preempt.
- Remove some unneeded Kconfigs for subsystems not (yet) available on CRIS
  (md, scsi, ieee1394, i2o, isdn, telephony, media, pcmcia, pci)
- Rename CRISv32 config items which had different types from CRISv10.
  (ETRAX_LED2G, ETRAX_LED2R, ETRAX_LED3G, ETRAX_LED3R, ETRAX_I2C_DATA_PORT,
  ETRAX_I2C_CLK_PORT)
2008-02-08 11:06:22 +01:00

300 lines
9.1 KiB
Plaintext

if ETRAX_ARCH_V32
source arch/cris/arch-v32/mach-fs/Kconfig
source arch/cris/arch-v32/mach-a3/Kconfig
source drivers/cpufreq/Kconfig
config ETRAX_DRAM_VIRTUAL_BASE
hex
depends on ETRAX_ARCH_V32
default "c0000000"
choice
prompt "Nbr of Ethernet LED groups"
depends on ETRAX_ARCH_V32
default ETRAX_NBR_LED_GRP_ONE
help
Select how many Ethernet LED groups that can be used. Usually one per Ethernet
interface is a good choice.
config ETRAX_NBR_LED_GRP_ZERO
bool "Use zero LED groups"
help
Select this if you do not want any Ethernet LEDs.
config ETRAX_NBR_LED_GRP_ONE
bool "Use one LED group"
help
Select this if you want one Ethernet LED group. This LED group
can be used for one or more Ethernet interfaces. However, it is
recomended that each Ethernet interface use a dedicated LED group.
config ETRAX_NBR_LED_GRP_TWO
bool "Use two LED groups"
help
Select this if you want two Ethernet LED groups. This is the
best choice if you have more than one Ethernet interface and
would like to have separate LEDs for the interfaces.
endchoice
config ETRAX_LED_G_NET0
string "Ethernet LED group 0 green LED bit"
depends on ETRAX_ARCH_V32 && (ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO)
default "PA3"
help
Bit to use for the green LED in Ethernet LED group 0.
config ETRAX_LED_R_NET0
string "Ethernet LED group 0 red LED bit"
depends on ETRAX_ARCH_V32 && (ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO)
default "PA4"
help
Bit to use for the red LED in Ethernet LED group 0.
config ETRAX_LED_G_NET1
string "Ethernet group 1 green LED bit"
depends on ETRAX_ARCH_V32 && ETRAX_NBR_LED_GRP_TWO
default ""
help
Bit to use for the green LED in Ethernet LED group 1.
config ETRAX_LED_R_NET1
string "Ethernet group 1 red LED bit"
depends on ETRAX_ARCH_V32 && ETRAX_NBR_LED_GRP_TWO
default ""
help
Bit to use for the red LED in Ethernet LED group 1.
config ETRAX_V32_LED2G
string "Second green LED bit"
depends on ETRAX_ARCH_V32
default "PA5"
help
Bit to use for the first green LED (status LED).
Most Axis products use bit A5 here.
config ETRAX_V32_LED2R
string "Second red LED bit"
depends on ETRAX_ARCH_V32
default "PA6"
help
Bit to use for the first red LED (network LED).
Most Axis products use bit A6 here.
config ETRAX_V32_LED3G
string "Third green LED bit"
depends on ETRAX_ARCH_V32
default "PA7"
help
Bit to use for the first green LED (drive/power LED).
Most Axis products use bit A7 here.
config ETRAX_V32_LED3R
string "Third red LED bit"
depends on ETRAX_ARCH_V32
default "PA7"
help
Bit to use for the first red LED (drive/power LED).
Most Axis products use bit A7 here.
choice
prompt "Kernel GDB port"
depends on ETRAX_KGDB
default ETRAX_KGDB_PORT0
help
Choose a serial port for kernel debugging. NOTE: This port should
not be enabled under Drivers for built-in interfaces (as it has its
own initialization code) and should not be the same as the debug port.
config ETRAX_KGDB_PORT4
bool "Serial-4"
depends on ETRAX_SERIAL_PORTS = 5
help
Use serial port 4 for kernel debugging.
endchoice
config ETRAX_MEM_GRP1_CONFIG
hex "MEM_GRP1_CONFIG"
depends on ETRAX_ARCH_V32
default "4044a"
help
Waitstates for flash. The default value is suitable for the
standard flashes used in axis products (120 ns).
config ETRAX_MEM_GRP2_CONFIG
hex "MEM_GRP2_CONFIG"
depends on ETRAX_ARCH_V32
default "0"
help
Waitstates for SRAM. 0 is a good choice for most Axis products.
config ETRAX_MEM_GRP3_CONFIG
hex "MEM_GRP3_CONFIG"
depends on ETRAX_ARCH_V32
default "0"
help
Waitstates for CSP0-3. 0 is a good choice for most Axis products.
It may need to be changed if external devices such as extra
register-mapped LEDs are used.
config ETRAX_MEM_GRP4_CONFIG
hex "MEM_GRP4_CONFIG"
depends on ETRAX_ARCH_V32
default "0"
help
Waitstates for CSP4-6. 0 is a good choice for most Axis products.
config ETRAX_SDRAM_GRP0_CONFIG
hex "SDRAM_GRP0_CONFIG"
depends on ETRAX_ARCH_V32
default "336"
help
SDRAM configuration for group 0. The value depends on the
hardware configuration. The default value is suitable
for 32 MB organized as two 16 bits chips (e.g. Axis
part number 18550) connected as one 32 bit device (i.e. in
the same group).
config ETRAX_SDRAM_GRP1_CONFIG
hex "SDRAM_GRP1_CONFIG"
depends on ETRAX_ARCH_V32
default "0"
help
SDRAM configuration for group 1. The default value is 0
because group 1 is not used in the default configuration,
described in the help for SDRAM_GRP0_CONFIG.
config ETRAX_SDRAM_TIMING
hex "SDRAM_TIMING"
depends on ETRAX_ARCH_V32
default "104a"
help
SDRAM timing parameters. The default value is ok for
most hardwares but large SDRAMs may require a faster
refresh (a.k.a 8K refresh). The default value implies
100MHz clock and SDR mode.
config ETRAX_SDRAM_COMMAND
hex "SDRAM_COMMAND"
depends on ETRAX_ARCH_V32
default "0"
help
SDRAM command. Should be 0 unless you really know what
you are doing (may be != 0 for unusual address line
mappings such as in a MCM)..
config ETRAX_DEF_GIO_PA_OE
hex "GIO_PA_OE"
depends on ETRAX_ARCH_V32
default "1c"
help
Configures the direction of general port A bits. 1 is out, 0 is in.
This is often totally different depending on the product used.
There are some guidelines though - if you know that only LED's are
connected to port PA, then they are usually connected to bits 2-4
and you can therefore use 1c. On other boards which don't have the
LED's at the general ports, these bits are used for all kinds of
stuff. If you don't know what to use, it is always safe to put all
as inputs, although floating inputs isn't good.
config ETRAX_DEF_GIO_PA_OUT
hex "GIO_PA_OUT"
depends on ETRAX_ARCH_V32
default "00"
help
Configures the initial data for the general port A bits. Most
products should use 00 here.
config ETRAX_DEF_GIO_PB_OE
hex "GIO_PB_OE"
depends on ETRAX_ARCH_V32
default "00000"
help
Configures the direction of general port B bits. 1 is out, 0 is in.
This is often totally different depending on the product used.
There are some guidelines though - if you know that only LED's are
connected to port PA, then they are usually connected to bits 2-4
and you can therefore use 1c. On other boards which don't have the
LED's at the general ports, these bits are used for all kinds of
stuff. If you don't know what to use, it is always safe to put all
as inputs, although floating inputs isn't good.
config ETRAX_DEF_GIO_PB_OUT
hex "GIO_PB_OUT"
depends on ETRAX_ARCH_V32
default "00000"
help
Configures the initial data for the general port B bits. Most
products should use 00000 here.
config ETRAX_DEF_GIO_PC_OE
hex "GIO_PC_OE"
depends on ETRAX_ARCH_V32
default "00000"
help
Configures the direction of general port C bits. 1 is out, 0 is in.
This is often totally different depending on the product used.
There are some guidelines though - if you know that only LED's are
connected to port PA, then they are usually connected to bits 2-4
and you can therefore use 1c. On other boards which don't have the
LED's at the general ports, these bits are used for all kinds of
stuff. If you don't know what to use, it is always safe to put all
as inputs, although floating inputs isn't good.
config ETRAX_DEF_GIO_PC_OUT
hex "GIO_PC_OUT"
depends on ETRAX_ARCH_V32
default "00000"
help
Configures the initial data for the general port C bits. Most
products should use 00000 here.
config ETRAX_DEF_GIO_PD_OE
hex "GIO_PD_OE"
depends on ETRAX_ARCH_V32
default "00000"
help
Configures the direction of general port D bits. 1 is out, 0 is in.
This is often totally different depending on the product used.
There are some guidelines though - if you know that only LED's are
connected to port PA, then they are usually connected to bits 2-4
and you can therefore use 1c. On other boards which don't have the
LED's at the general ports, these bits are used for all kinds of
stuff. If you don't know what to use, it is always safe to put all
as inputs, although floating inputs isn't good.
config ETRAX_DEF_GIO_PD_OUT
hex "GIO_PD_OUT"
depends on ETRAX_ARCH_V32
default "00000"
help
Configures the initial data for the general port D bits. Most
products should use 00000 here.
config ETRAX_DEF_GIO_PE_OE
hex "GIO_PE_OE"
depends on ETRAX_ARCH_V32
default "00000"
help
Configures the direction of general port E bits. 1 is out, 0 is in.
This is often totally different depending on the product used.
There are some guidelines though - if you know that only LED's are
connected to port PA, then they are usually connected to bits 2-4
and you can therefore use 1c. On other boards which don't have the
LED's at the general ports, these bits are used for all kinds of
stuff. If you don't know what to use, it is always safe to put all
as inputs, although floating inputs isn't good.
config ETRAX_DEF_GIO_PE_OUT
hex "GIO_PE_OUT"
depends on ETRAX_ARCH_V32
default "00000"
help
Configures the initial data for the general port E bits. Most
products should use 00000 here.
endif