28187f2ce3
Patch from Lennert Buytenhek This patch converts the ixp2000 serial port over to a platform serial device. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Deepak Saxena <dsaxena@plexity.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
149 lines
4.5 KiB
C
149 lines
4.5 KiB
C
/*
|
|
* include/asm-arm/arch-ixp2000/platform.h
|
|
*
|
|
* Various bits of code used by platform-level code.
|
|
*
|
|
* Author: Deepak Saxena <dsaxena@plexity.net>
|
|
*
|
|
* Copyright 2004 (c) MontaVista Software, Inc.
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public
|
|
* License version 2. This program is licensed "as is" without any
|
|
* warranty of any kind, whether express or implied.
|
|
*/
|
|
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/*
|
|
* The IXP2400 B0 silicon contains an erratum (#66) that causes writes
|
|
* to on-chip I/O register to not complete fully. What this means is
|
|
* that if you have a write to on-chip I/O followed by a back-to-back
|
|
* read or write, the first write will happen twice. OR...if it's
|
|
* not a back-to-back transaction, the read or write will generate
|
|
* incorrect data.
|
|
*
|
|
* The official work around for this is to set the on-chip I/O regions
|
|
* as XCB=101 and then force a read-back from the register.
|
|
*
|
|
*/
|
|
#if defined(CONFIG_ARCH_ENP2611) || defined(CONFIG_ARCH_IXDP2400) || defined(CONFIG_ARCH_IXDP2401)
|
|
|
|
#include <asm/system.h> /* Pickup local_irq_ functions */
|
|
|
|
static inline void ixp2000_reg_write(volatile unsigned long *reg, unsigned long val)
|
|
{
|
|
volatile unsigned long dummy;
|
|
unsigned long flags;
|
|
|
|
local_irq_save(flags);
|
|
*reg = val;
|
|
barrier();
|
|
dummy = *reg;
|
|
local_irq_restore(flags);
|
|
}
|
|
#else
|
|
#define ixp2000_reg_write(reg, val) (*reg = val)
|
|
#endif /* IXDP2400 || IXDP2401 */
|
|
|
|
/*
|
|
* Boards may multiplex different devices on the 2nd channel of
|
|
* the slowport interface that each need different configuration
|
|
* settings. For example, the IXDP2400 uses channel 2 on the interface
|
|
* to access the CPLD, the switch fabric card, and the media card. Each
|
|
* one needs a different mode so drivers must save/restore the mode
|
|
* before and after each operation.
|
|
*
|
|
* acquire_slowport(&your_config);
|
|
* ...
|
|
* do slowport operations
|
|
* ...
|
|
* release_slowport();
|
|
*
|
|
* Note that while you have the slowport, you are holding a spinlock,
|
|
* so your code should be written as if you explicitly acquired a lock.
|
|
*
|
|
* The configuration only affects device 2 on the slowport, so the
|
|
* MTD map driver does not acquire/release the slowport.
|
|
*/
|
|
struct slowport_cfg {
|
|
unsigned long CCR; /* Clock divide */
|
|
unsigned long WTC; /* Write Timing Control */
|
|
unsigned long RTC; /* Read Timing Control */
|
|
unsigned long PCR; /* Protocol Control Register */
|
|
unsigned long ADC; /* Address/Data Width Control */
|
|
};
|
|
|
|
|
|
void ixp2000_acquire_slowport(struct slowport_cfg *, struct slowport_cfg *);
|
|
void ixp2000_release_slowport(struct slowport_cfg *);
|
|
|
|
/*
|
|
* IXP2400 A0/A1 and IXP2800 A0/A1/A2 have broken slowport that requires
|
|
* tweaking of addresses in the MTD driver.
|
|
*/
|
|
static inline unsigned ixp2000_has_broken_slowport(void)
|
|
{
|
|
unsigned long id = *IXP2000_PROD_ID;
|
|
unsigned long id_prod = id & (IXP2000_MAJ_PROD_TYPE_MASK |
|
|
IXP2000_MIN_PROD_TYPE_MASK);
|
|
return (((id_prod ==
|
|
/* fixed in IXP2400-B0 */
|
|
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
|
|
IXP2000_MIN_PROD_TYPE_IXP2400)) &&
|
|
((id & IXP2000_MAJ_REV_MASK) == 0)) ||
|
|
((id_prod ==
|
|
/* fixed in IXP2800-B0 */
|
|
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
|
|
IXP2000_MIN_PROD_TYPE_IXP2800)) &&
|
|
((id & IXP2000_MAJ_REV_MASK) == 0)) ||
|
|
((id_prod ==
|
|
/* fixed in IXP2850-B0 */
|
|
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
|
|
IXP2000_MIN_PROD_TYPE_IXP2850)) &&
|
|
((id & IXP2000_MAJ_REV_MASK) == 0)));
|
|
}
|
|
|
|
static inline unsigned int ixp2000_has_flash(void)
|
|
{
|
|
return ((*IXP2000_STRAP_OPTIONS) & (CFG_BOOT_PROM));
|
|
}
|
|
|
|
static inline unsigned int ixp2000_is_pcimaster(void)
|
|
{
|
|
return ((*IXP2000_STRAP_OPTIONS) & (CFG_PCI_BOOT_HOST));
|
|
}
|
|
|
|
void ixp2000_map_io(void);
|
|
void ixp2000_uart_init(void);
|
|
void ixp2000_init_irq(void);
|
|
void ixp2000_init_time(unsigned long);
|
|
unsigned long ixp2000_gettimeoffset(void);
|
|
|
|
struct pci_sys_data;
|
|
|
|
u32 *ixp2000_pci_config_addr(unsigned int bus, unsigned int devfn, int where);
|
|
void ixp2000_pci_preinit(void);
|
|
int ixp2000_pci_setup(int, struct pci_sys_data*);
|
|
struct pci_bus* ixp2000_pci_scan_bus(int, struct pci_sys_data*);
|
|
int ixp2000_pci_read_config(struct pci_bus*, unsigned int, int, int, u32 *);
|
|
int ixp2000_pci_write_config(struct pci_bus*, unsigned int, int, int, u32);
|
|
|
|
/*
|
|
* Several of the IXP2000 systems have banked flash so we need to extend the
|
|
* flash_platform_data structure with some private pointers
|
|
*/
|
|
struct ixp2000_flash_data {
|
|
struct flash_platform_data *platform_data;
|
|
int nr_banks;
|
|
unsigned long (*bank_setup)(unsigned long);
|
|
};
|
|
|
|
struct ixp2000_i2c_pins {
|
|
unsigned long sda_pin;
|
|
unsigned long scl_pin;
|
|
};
|
|
|
|
|
|
#endif /* !__ASSEMBLY__ */
|