android_kernel_xiaomi_sm8350/include/asm-m68knommu/m527xsim.h
Greg Ungerer d871629b83 [PATCH] m68knommu: allow for SDRAM and GPIO differences on 5270/1 and 5274/5 processors
Allow for differences in the SDRAM controller setup and GPIO pin setup
of the 5270/1 and 5274/5 parts. With separate config options for each
now this no longer needs to be board specific.

Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-11 20:43:47 -07:00

76 lines
2.6 KiB
C

/****************************************************************************/
/*
* m527xsim.h -- ColdFire 5270/5271 System Integration Module support.
*
* (C) Copyright 2004, Greg Ungerer (gerg@snapgear.com)
*/
/****************************************************************************/
#ifndef m527xsim_h
#define m527xsim_h
/****************************************************************************/
#include <linux/config.h>
/*
* Define the 5270/5271 SIM register set addresses.
*/
#define MCFICM_INTC0 0x0c00 /* Base for Interrupt Ctrl 0 */
#define MCFICM_INTC1 0x0d00 /* Base for Interrupt Ctrl 1 */
#define MCFINTC_IPRH 0x00 /* Interrupt pending 32-63 */
#define MCFINTC_IPRL 0x04 /* Interrupt pending 1-31 */
#define MCFINTC_IMRH 0x08 /* Interrupt mask 32-63 */
#define MCFINTC_IMRL 0x0c /* Interrupt mask 1-31 */
#define MCFINTC_INTFRCH 0x10 /* Interrupt force 32-63 */
#define MCFINTC_INTFRCL 0x14 /* Interrupt force 1-31 */
#define MCFINTC_IRLR 0x18 /* */
#define MCFINTC_IACKL 0x19 /* */
#define MCFINTC_ICR0 0x40 /* Base ICR register */
#define MCFINT_VECBASE 64 /* Vector base number */
#define MCFINT_UART0 13 /* Interrupt number for UART0 */
#define MCFINT_UART1 14 /* Interrupt number for UART1 */
#define MCFINT_UART2 15 /* Interrupt number for UART2 */
#define MCFINT_PIT1 36 /* Interrupt number for PIT1 */
/*
* SDRAM configuration registers.
*/
#ifdef CONFIG_M5271
#define MCFSIM_DCR 0x40 /* SDRAM control */
#define MCFSIM_DACR0 0x48 /* SDRAM base address 0 */
#define MCFSIM_DMR0 0x4c /* SDRAM address mask 0 */
#define MCFSIM_DACR1 0x50 /* SDRAM base address 1 */
#define MCFSIM_DMR1 0x54 /* SDRAM address mask 1 */
#endif
#ifdef CONFIG_M5275
#define MCFSIM_DMR 0x40 /* SDRAM mode */
#define MCFSIM_DCR 0x44 /* SDRAM control */
#define MCFSIM_DCFG1 0x48 /* SDRAM configuration 1 */
#define MCFSIM_DCFG2 0x4c /* SDRAM configuration 2 */
#define MCFSIM_DBAR0 0x50 /* SDRAM base address 0 */
#define MCFSIM_DMR0 0x54 /* SDRAM address mask 0 */
#define MCFSIM_DBAR1 0x58 /* SDRAM base address 1 */
#define MCFSIM_DMR1 0x5c /* SDRAM address mask 1 */
#endif
/*
* GPIO pins setups to enable the UARTs.
*/
#ifdef CONFIG_M5271
#define MCF_GPIO_PAR_UART 0x100048 /* PAR UART address */
#define UART0_ENABLE_MASK 0x000f
#define UART1_ENABLE_MASK 0x0ff0
#define UART2_ENABLE_MASK 0x3000
#endif
#ifdef CONFIG_M5275
#define MCF_GPIO_PAR_UART 0x10007c /* PAR UART address */
#define UART0_ENABLE_MASK 0x000f
#define UART1_ENABLE_MASK 0x00f0
#define UART2_ENABLE_MASK 0x3f00
#endif
/****************************************************************************/
#endif /* m527xsim_h */