8704de8f29
* Fix SWDMA/MWDMA masks in cy82c693_chipset. * Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to check whether the DMA should be enabled even if ide_max_dma_mode() fails. * Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode() and remove no longer needed cy82c693_ide_dma_on(). Then set IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in cy82c693_chipset. * Bump driver version. As a result of this patch cy82c693 driver will configure and use DMA on all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
460 lines
14 KiB
C
460 lines
14 KiB
C
/*
|
|
* linux/drivers/ide/pci/cy82c693.c Version 0.44 Nov 8, 2007
|
|
*
|
|
* Copyright (C) 1998-2000 Andreas S. Krebs (akrebs@altavista.net), Maintainer
|
|
* Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>, Integrator
|
|
*
|
|
* CYPRESS CY82C693 chipset IDE controller
|
|
*
|
|
* The CY82C693 chipset is used on Digital's PC-Alpha 164SX boards.
|
|
* Writing the driver was quite simple, since most of the job is
|
|
* done by the generic pci-ide support.
|
|
* The hard part was finding the CY82C693's datasheet on Cypress's
|
|
* web page :-(. But Altavista solved this problem :-).
|
|
*
|
|
*
|
|
* Notes:
|
|
* - I recently got a 16.8G IBM DTTA, so I was able to test it with
|
|
* a large and fast disk - the results look great, so I'd say the
|
|
* driver is working fine :-)
|
|
* hdparm -t reports 8.17 MB/sec at about 6% CPU usage for the DTTA
|
|
* - this is my first linux driver, so there's probably a lot of room
|
|
* for optimizations and bug fixing, so feel free to do it.
|
|
* - use idebus=xx parameter to set PCI bus speed - needed to calc
|
|
* timings for PIO modes (default will be 40)
|
|
* - if using PIO mode it's a good idea to set the PIO mode and
|
|
* 32-bit I/O support (if possible), e.g. hdparm -p2 -c1 /dev/hda
|
|
* - I had some problems with my IBM DHEA with PIO modes < 2
|
|
* (lost interrupts) ?????
|
|
* - first tests with DMA look okay, they seem to work, but there is a
|
|
* problem with sound - the BusMaster IDE TimeOut should fixed this
|
|
*
|
|
* Ancient History:
|
|
* AMH@1999-08-24: v0.34 init_cy82c693_chip moved to pci_init_cy82c693
|
|
* ASK@1999-01-23: v0.33 made a few minor code clean ups
|
|
* removed DMA clock speed setting by default
|
|
* added boot message
|
|
* ASK@1998-11-01: v0.32 added support to set BusMaster IDE TimeOut
|
|
* added support to set DMA Controller Clock Speed
|
|
* ASK@1998-10-31: v0.31 fixed problem with setting to high DMA modes
|
|
* on some drives.
|
|
* ASK@1998-10-29: v0.3 added support to set DMA modes
|
|
* ASK@1998-10-28: v0.2 added support to set PIO modes
|
|
* ASK@1998-10-27: v0.1 first version - chipset detection
|
|
*
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/types.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/ide.h>
|
|
#include <linux/init.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
/* the current version */
|
|
#define CY82_VERSION "CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs@altavista.net)"
|
|
|
|
/*
|
|
* The following are used to debug the driver.
|
|
*/
|
|
#define CY82C693_DEBUG_LOGS 0
|
|
#define CY82C693_DEBUG_INFO 0
|
|
|
|
/* define CY82C693_SETDMA_CLOCK to set DMA Controller Clock Speed to ATCLK */
|
|
#undef CY82C693_SETDMA_CLOCK
|
|
|
|
/*
|
|
* NOTE: the value for busmaster timeout is tricky and I got it by
|
|
* trial and error! By using a to low value will cause DMA timeouts
|
|
* and drop IDE performance, and by using a to high value will cause
|
|
* audio playback to scatter.
|
|
* If you know a better value or how to calc it, please let me know.
|
|
*/
|
|
|
|
/* twice the value written in cy82c693ub datasheet */
|
|
#define BUSMASTER_TIMEOUT 0x50
|
|
/*
|
|
* the value above was tested on my machine and it seems to work okay
|
|
*/
|
|
|
|
/* here are the offset definitions for the registers */
|
|
#define CY82_IDE_CMDREG 0x04
|
|
#define CY82_IDE_ADDRSETUP 0x48
|
|
#define CY82_IDE_MASTER_IOR 0x4C
|
|
#define CY82_IDE_MASTER_IOW 0x4D
|
|
#define CY82_IDE_SLAVE_IOR 0x4E
|
|
#define CY82_IDE_SLAVE_IOW 0x4F
|
|
#define CY82_IDE_MASTER_8BIT 0x50
|
|
#define CY82_IDE_SLAVE_8BIT 0x51
|
|
|
|
#define CY82_INDEX_PORT 0x22
|
|
#define CY82_DATA_PORT 0x23
|
|
|
|
#define CY82_INDEX_CTRLREG1 0x01
|
|
#define CY82_INDEX_CHANNEL0 0x30
|
|
#define CY82_INDEX_CHANNEL1 0x31
|
|
#define CY82_INDEX_TIMEOUT 0x32
|
|
|
|
/* the min and max PCI bus speed in MHz - from datasheet */
|
|
#define CY82C963_MIN_BUS_SPEED 25
|
|
#define CY82C963_MAX_BUS_SPEED 33
|
|
|
|
/* the struct for the PIO mode timings */
|
|
typedef struct pio_clocks_s {
|
|
u8 address_time; /* Address setup (clocks) */
|
|
u8 time_16r; /* clocks for 16bit IOR (0xF0=Active/data, 0x0F=Recovery) */
|
|
u8 time_16w; /* clocks for 16bit IOW (0xF0=Active/data, 0x0F=Recovery) */
|
|
u8 time_8; /* clocks for 8bit (0xF0=Active/data, 0x0F=Recovery) */
|
|
} pio_clocks_t;
|
|
|
|
/*
|
|
* calc clocks using bus_speed
|
|
* returns (rounded up) time in bus clocks for time in ns
|
|
*/
|
|
static int calc_clk (int time, int bus_speed)
|
|
{
|
|
int clocks;
|
|
|
|
clocks = (time*bus_speed+999)/1000 -1;
|
|
|
|
if (clocks < 0)
|
|
clocks = 0;
|
|
|
|
if (clocks > 0x0F)
|
|
clocks = 0x0F;
|
|
|
|
return clocks;
|
|
}
|
|
|
|
/*
|
|
* compute the values for the clock registers for PIO
|
|
* mode and pci_clk [MHz] speed
|
|
*
|
|
* NOTE: for mode 0,1 and 2 drives 8-bit IDE command control registers are used
|
|
* for mode 3 and 4 drives 8 and 16-bit timings are the same
|
|
*
|
|
*/
|
|
static void compute_clocks (u8 pio, pio_clocks_t *p_pclk)
|
|
{
|
|
int clk1, clk2;
|
|
int bus_speed = system_bus_clock(); /* get speed of PCI bus */
|
|
|
|
/* we don't check against CY82C693's min and max speed,
|
|
* so you can play with the idebus=xx parameter
|
|
*/
|
|
|
|
/* let's calc the address setup time clocks */
|
|
p_pclk->address_time = (u8)calc_clk(ide_pio_timings[pio].setup_time, bus_speed);
|
|
|
|
/* let's calc the active and recovery time clocks */
|
|
clk1 = calc_clk(ide_pio_timings[pio].active_time, bus_speed);
|
|
|
|
/* calc recovery timing */
|
|
clk2 = ide_pio_timings[pio].cycle_time -
|
|
ide_pio_timings[pio].active_time -
|
|
ide_pio_timings[pio].setup_time;
|
|
|
|
clk2 = calc_clk(clk2, bus_speed);
|
|
|
|
clk1 = (clk1<<4)|clk2; /* combine active and recovery clocks */
|
|
|
|
/* note: we use the same values for 16bit IOR and IOW
|
|
* those are all the same, since I don't have other
|
|
* timings than those from ide-lib.c
|
|
*/
|
|
|
|
p_pclk->time_16r = (u8)clk1;
|
|
p_pclk->time_16w = (u8)clk1;
|
|
|
|
/* what are good values for 8bit ?? */
|
|
p_pclk->time_8 = (u8)clk1;
|
|
}
|
|
|
|
/*
|
|
* set DMA mode a specific channel for CY82C693
|
|
*/
|
|
|
|
static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
|
|
{
|
|
ide_hwif_t *hwif = drive->hwif;
|
|
u8 single = (mode & 0x10) >> 4, index = 0, data = 0;
|
|
|
|
index = hwif->channel ? CY82_INDEX_CHANNEL1 : CY82_INDEX_CHANNEL0;
|
|
|
|
#if CY82C693_DEBUG_LOGS
|
|
/* for debug let's show the previous values */
|
|
|
|
outb(index, CY82_INDEX_PORT);
|
|
data = inb(CY82_DATA_PORT);
|
|
|
|
printk (KERN_INFO "%s (ch=%d, dev=%d): DMA mode is %d (single=%d)\n",
|
|
drive->name, HWIF(drive)->channel, drive->select.b.unit,
|
|
(data&0x3), ((data>>2)&1));
|
|
#endif /* CY82C693_DEBUG_LOGS */
|
|
|
|
data = (mode & 3) | (single << 2);
|
|
|
|
outb(index, CY82_INDEX_PORT);
|
|
outb(data, CY82_DATA_PORT);
|
|
|
|
#if CY82C693_DEBUG_INFO
|
|
printk(KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n",
|
|
drive->name, HWIF(drive)->channel, drive->select.b.unit,
|
|
mode & 3, single);
|
|
#endif /* CY82C693_DEBUG_INFO */
|
|
|
|
/*
|
|
* note: below we set the value for Bus Master IDE TimeOut Register
|
|
* I'm not absolutly sure what this does, but it solved my problem
|
|
* with IDE DMA and sound, so I now can play sound and work with
|
|
* my IDE driver at the same time :-)
|
|
*
|
|
* If you know the correct (best) value for this register please
|
|
* let me know - ASK
|
|
*/
|
|
|
|
data = BUSMASTER_TIMEOUT;
|
|
outb(CY82_INDEX_TIMEOUT, CY82_INDEX_PORT);
|
|
outb(data, CY82_DATA_PORT);
|
|
|
|
#if CY82C693_DEBUG_INFO
|
|
printk (KERN_INFO "%s: Set IDE Bus Master TimeOut Register to 0x%X\n",
|
|
drive->name, data);
|
|
#endif /* CY82C693_DEBUG_INFO */
|
|
}
|
|
|
|
static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
pio_clocks_t pclk;
|
|
unsigned int addrCtrl;
|
|
|
|
/* select primary or secondary channel */
|
|
if (hwif->index > 0) { /* drive is on the secondary channel */
|
|
dev = pci_get_slot(dev->bus, dev->devfn+1);
|
|
if (!dev) {
|
|
printk(KERN_ERR "%s: tune_drive: "
|
|
"Cannot find secondary interface!\n",
|
|
drive->name);
|
|
return;
|
|
}
|
|
}
|
|
|
|
#if CY82C693_DEBUG_LOGS
|
|
/* for debug let's show the register values */
|
|
|
|
if (drive->select.b.unit == 0) {
|
|
/*
|
|
* get master drive registers
|
|
* address setup control register
|
|
* is 32 bit !!!
|
|
*/
|
|
pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
|
|
addrCtrl &= 0x0F;
|
|
|
|
/* now let's get the remaining registers */
|
|
pci_read_config_byte(dev, CY82_IDE_MASTER_IOR, &pclk.time_16r);
|
|
pci_read_config_byte(dev, CY82_IDE_MASTER_IOW, &pclk.time_16w);
|
|
pci_read_config_byte(dev, CY82_IDE_MASTER_8BIT, &pclk.time_8);
|
|
} else {
|
|
/*
|
|
* set slave drive registers
|
|
* address setup control register
|
|
* is 32 bit !!!
|
|
*/
|
|
pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
|
|
|
|
addrCtrl &= 0xF0;
|
|
addrCtrl >>= 4;
|
|
|
|
/* now let's get the remaining registers */
|
|
pci_read_config_byte(dev, CY82_IDE_SLAVE_IOR, &pclk.time_16r);
|
|
pci_read_config_byte(dev, CY82_IDE_SLAVE_IOW, &pclk.time_16w);
|
|
pci_read_config_byte(dev, CY82_IDE_SLAVE_8BIT, &pclk.time_8);
|
|
}
|
|
|
|
printk(KERN_INFO "%s (ch=%d, dev=%d): PIO timing is "
|
|
"(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
|
|
drive->name, hwif->channel, drive->select.b.unit,
|
|
addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
|
|
#endif /* CY82C693_DEBUG_LOGS */
|
|
|
|
/* let's calc the values for this PIO mode */
|
|
compute_clocks(pio, &pclk);
|
|
|
|
/* now let's write the clocks registers */
|
|
if (drive->select.b.unit == 0) {
|
|
/*
|
|
* set master drive
|
|
* address setup control register
|
|
* is 32 bit !!!
|
|
*/
|
|
pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
|
|
|
|
addrCtrl &= (~0xF);
|
|
addrCtrl |= (unsigned int)pclk.address_time;
|
|
pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);
|
|
|
|
/* now let's set the remaining registers */
|
|
pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r);
|
|
pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w);
|
|
pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8);
|
|
|
|
addrCtrl &= 0xF;
|
|
} else {
|
|
/*
|
|
* set slave drive
|
|
* address setup control register
|
|
* is 32 bit !!!
|
|
*/
|
|
pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
|
|
|
|
addrCtrl &= (~0xF0);
|
|
addrCtrl |= ((unsigned int)pclk.address_time<<4);
|
|
pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);
|
|
|
|
/* now let's set the remaining registers */
|
|
pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r);
|
|
pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w);
|
|
pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8);
|
|
|
|
addrCtrl >>= 4;
|
|
addrCtrl &= 0xF;
|
|
}
|
|
|
|
#if CY82C693_DEBUG_INFO
|
|
printk(KERN_INFO "%s (ch=%d, dev=%d): set PIO timing to "
|
|
"(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
|
|
drive->name, hwif->channel, drive->select.b.unit,
|
|
addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
|
|
#endif /* CY82C693_DEBUG_INFO */
|
|
}
|
|
|
|
/*
|
|
* this function is called during init and is used to setup the cy82c693 chip
|
|
*/
|
|
static unsigned int __devinit init_chipset_cy82c693(struct pci_dev *dev, const char *name)
|
|
{
|
|
if (PCI_FUNC(dev->devfn) != 1)
|
|
return 0;
|
|
|
|
#ifdef CY82C693_SETDMA_CLOCK
|
|
u8 data = 0;
|
|
#endif /* CY82C693_SETDMA_CLOCK */
|
|
|
|
/* write info about this verion of the driver */
|
|
printk(KERN_INFO CY82_VERSION "\n");
|
|
|
|
#ifdef CY82C693_SETDMA_CLOCK
|
|
/* okay let's set the DMA clock speed */
|
|
|
|
outb(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT);
|
|
data = inb(CY82_DATA_PORT);
|
|
|
|
#if CY82C693_DEBUG_INFO
|
|
printk(KERN_INFO "%s: Peripheral Configuration Register: 0x%X\n",
|
|
name, data);
|
|
#endif /* CY82C693_DEBUG_INFO */
|
|
|
|
/*
|
|
* for some reason sometimes the DMA controller
|
|
* speed is set to ATCLK/2 ???? - we fix this here
|
|
*
|
|
* note: i don't know what causes this strange behaviour,
|
|
* but even changing the dma speed doesn't solve it :-(
|
|
* the ide performance is still only half the normal speed
|
|
*
|
|
* if anybody knows what goes wrong with my machine, please
|
|
* let me know - ASK
|
|
*/
|
|
|
|
data |= 0x03;
|
|
|
|
outb(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT);
|
|
outb(data, CY82_DATA_PORT);
|
|
|
|
#if CY82C693_DEBUG_INFO
|
|
printk (KERN_INFO "%s: New Peripheral Configuration Register: 0x%X\n",
|
|
name, data);
|
|
#endif /* CY82C693_DEBUG_INFO */
|
|
|
|
#endif /* CY82C693_SETDMA_CLOCK */
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* the init function - called for each ide channel once
|
|
*/
|
|
static void __devinit init_hwif_cy82c693(ide_hwif_t *hwif)
|
|
{
|
|
hwif->set_pio_mode = &cy82c693_set_pio_mode;
|
|
hwif->set_dma_mode = &cy82c693_set_dma_mode;
|
|
}
|
|
|
|
static void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
|
|
{
|
|
static ide_hwif_t *primary;
|
|
|
|
if (PCI_FUNC(hwif->pci_dev->devfn) == 1)
|
|
primary = hwif;
|
|
else {
|
|
hwif->mate = primary;
|
|
hwif->channel = 1;
|
|
}
|
|
}
|
|
|
|
static const struct ide_port_info cy82c693_chipset __devinitdata = {
|
|
.name = "CY82C693",
|
|
.init_chipset = init_chipset_cy82c693,
|
|
.init_iops = init_iops_cy82c693,
|
|
.init_hwif = init_hwif_cy82c693,
|
|
.chipset = ide_cy82c693,
|
|
.host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_CY82C693 |
|
|
IDE_HFLAG_BOOTABLE,
|
|
.pio_mask = ATA_PIO4,
|
|
.swdma_mask = ATA_SWDMA2,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
};
|
|
|
|
static int __devinit cy82c693_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
struct pci_dev *dev2;
|
|
int ret = -ENODEV;
|
|
|
|
/* CY82C693 is more than only a IDE controller.
|
|
Function 1 is primary IDE channel, function 2 - secondary. */
|
|
if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE &&
|
|
PCI_FUNC(dev->devfn) == 1) {
|
|
dev2 = pci_get_slot(dev->bus, dev->devfn + 1);
|
|
ret = ide_setup_pci_devices(dev, dev2, &cy82c693_chipset);
|
|
/* We leak pci refs here but thats ok - we can't be unloaded */
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
static const struct pci_device_id cy82c693_pci_tbl[] = {
|
|
{ PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), 0 },
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, cy82c693_pci_tbl);
|
|
|
|
static struct pci_driver driver = {
|
|
.name = "Cypress_IDE",
|
|
.id_table = cy82c693_pci_tbl,
|
|
.probe = cy82c693_init_one,
|
|
};
|
|
|
|
static int __init cy82c693_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&driver);
|
|
}
|
|
|
|
module_init(cy82c693_ide_init);
|
|
|
|
MODULE_AUTHOR("Andreas Krebs, Andre Hedrick");
|
|
MODULE_DESCRIPTION("PCI driver module for the Cypress CY82C693 IDE");
|
|
MODULE_LICENSE("GPL");
|