android_kernel_xiaomi_sm8350/include/asm-m68k/apollodma.h
Adrian Bunk f30828a674 m68k: remove CVS keywords
This patch removes CVS keywords that weren't updated for a long time
from comments.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-20 17:24:38 -07:00

249 lines
9.2 KiB
C

/*
* linux/include/asm/dma.h: Defines for using and allocating dma channels.
* Written by Hennus Bergman, 1992.
* High DMA channel support & info by Hannu Savolainen
* and John Boyd, Nov. 1992.
*/
#ifndef _ASM_APOLLO_DMA_H
#define _ASM_APOLLO_DMA_H
#include <asm/apollohw.h> /* need byte IO */
#include <linux/spinlock.h> /* And spinlocks */
#include <linux/delay.h>
#define dma_outb(val,addr) (*((volatile unsigned char *)(addr+IO_BASE)) = (val))
#define dma_inb(addr) (*((volatile unsigned char *)(addr+IO_BASE)))
/*
* NOTES about DMA transfers:
*
* controller 1: channels 0-3, byte operations, ports 00-1F
* controller 2: channels 4-7, word operations, ports C0-DF
*
* - ALL registers are 8 bits only, regardless of transfer size
* - channel 4 is not used - cascades 1 into 2.
* - channels 0-3 are byte - addresses/counts are for physical bytes
* - channels 5-7 are word - addresses/counts are for physical words
* - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
* - transfer count loaded to registers is 1 less than actual count
* - controller 2 offsets are all even (2x offsets for controller 1)
* - page registers for 5-7 don't use data bit 0, represent 128K pages
* - page registers for 0-3 use bit 0, represent 64K pages
*
* DMA transfers are limited to the lower 16MB of _physical_ memory.
* Note that addresses loaded into registers must be _physical_ addresses,
* not logical addresses (which may differ if paging is active).
*
* Address mapping for channels 0-3:
*
* A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses)
* | ... | | ... | | ... |
* | ... | | ... | | ... |
* | ... | | ... | | ... |
* P7 ... P0 A7 ... A0 A7 ... A0
* | Page | Addr MSB | Addr LSB | (DMA registers)
*
* Address mapping for channels 5-7:
*
* A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses)
* | ... | \ \ ... \ \ \ ... \ \
* | ... | \ \ ... \ \ \ ... \ (not used)
* | ... | \ \ ... \ \ \ ... \
* P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0
* | Page | Addr MSB | Addr LSB | (DMA registers)
*
* Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
* and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
* the hardware level, so odd-byte transfers aren't possible).
*
* Transfer count (_not # bytes_) is limited to 64K, represented as actual
* count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more,
* and up to 128K bytes may be transferred on channels 5-7 in one operation.
*
*/
#define MAX_DMA_CHANNELS 8
/* The maximum address that we can perform a DMA transfer to on this platform */#define MAX_DMA_ADDRESS (PAGE_OFFSET+0x1000000)
/* 8237 DMA controllers */
#define IO_DMA1_BASE 0x10C00 /* 8 bit slave DMA, channels 0..3 */
#define IO_DMA2_BASE 0x10D00 /* 16 bit master DMA, ch 4(=slave input)..7 */
/* DMA controller registers */
#define DMA1_CMD_REG (IO_DMA1_BASE+0x08) /* command register (w) */
#define DMA1_STAT_REG (IO_DMA1_BASE+0x08) /* status register (r) */
#define DMA1_REQ_REG (IO_DMA1_BASE+0x09) /* request register (w) */
#define DMA1_MASK_REG (IO_DMA1_BASE+0x0A) /* single-channel mask (w) */
#define DMA1_MODE_REG (IO_DMA1_BASE+0x0B) /* mode register (w) */
#define DMA1_CLEAR_FF_REG (IO_DMA1_BASE+0x0C) /* clear pointer flip-flop (w) */
#define DMA1_TEMP_REG (IO_DMA1_BASE+0x0D) /* Temporary Register (r) */
#define DMA1_RESET_REG (IO_DMA1_BASE+0x0D) /* Master Clear (w) */
#define DMA1_CLR_MASK_REG (IO_DMA1_BASE+0x0E) /* Clear Mask */
#define DMA1_MASK_ALL_REG (IO_DMA1_BASE+0x0F) /* all-channels mask (w) */
#define DMA2_CMD_REG (IO_DMA2_BASE+0x10) /* command register (w) */
#define DMA2_STAT_REG (IO_DMA2_BASE+0x10) /* status register (r) */
#define DMA2_REQ_REG (IO_DMA2_BASE+0x12) /* request register (w) */
#define DMA2_MASK_REG (IO_DMA2_BASE+0x14) /* single-channel mask (w) */
#define DMA2_MODE_REG (IO_DMA2_BASE+0x16) /* mode register (w) */
#define DMA2_CLEAR_FF_REG (IO_DMA2_BASE+0x18) /* clear pointer flip-flop (w) */
#define DMA2_TEMP_REG (IO_DMA2_BASE+0x1A) /* Temporary Register (r) */
#define DMA2_RESET_REG (IO_DMA2_BASE+0x1A) /* Master Clear (w) */
#define DMA2_CLR_MASK_REG (IO_DMA2_BASE+0x1C) /* Clear Mask */
#define DMA2_MASK_ALL_REG (IO_DMA2_BASE+0x1E) /* all-channels mask (w) */
#define DMA_ADDR_0 (IO_DMA1_BASE+0x00) /* DMA address registers */
#define DMA_ADDR_1 (IO_DMA1_BASE+0x02)
#define DMA_ADDR_2 (IO_DMA1_BASE+0x04)
#define DMA_ADDR_3 (IO_DMA1_BASE+0x06)
#define DMA_ADDR_4 (IO_DMA2_BASE+0x00)
#define DMA_ADDR_5 (IO_DMA2_BASE+0x04)
#define DMA_ADDR_6 (IO_DMA2_BASE+0x08)
#define DMA_ADDR_7 (IO_DMA2_BASE+0x0C)
#define DMA_CNT_0 (IO_DMA1_BASE+0x01) /* DMA count registers */
#define DMA_CNT_1 (IO_DMA1_BASE+0x03)
#define DMA_CNT_2 (IO_DMA1_BASE+0x05)
#define DMA_CNT_3 (IO_DMA1_BASE+0x07)
#define DMA_CNT_4 (IO_DMA2_BASE+0x02)
#define DMA_CNT_5 (IO_DMA2_BASE+0x06)
#define DMA_CNT_6 (IO_DMA2_BASE+0x0A)
#define DMA_CNT_7 (IO_DMA2_BASE+0x0E)
#define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */
#define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */
#define DMA_MODE_CASCADE 0xC0 /* pass thru DREQ->HRQ, DACK<-HLDA only */
#define DMA_AUTOINIT 0x10
#define DMA_8BIT 0
#define DMA_16BIT 1
#define DMA_BUSMASTER 2
extern spinlock_t dma_spin_lock;
static __inline__ unsigned long claim_dma_lock(void)
{
unsigned long flags;
spin_lock_irqsave(&dma_spin_lock, flags);
return flags;
}
static __inline__ void release_dma_lock(unsigned long flags)
{
spin_unlock_irqrestore(&dma_spin_lock, flags);
}
/* enable/disable a specific DMA channel */
static __inline__ void enable_dma(unsigned int dmanr)
{
if (dmanr<=3)
dma_outb(dmanr, DMA1_MASK_REG);
else
dma_outb(dmanr & 3, DMA2_MASK_REG);
}
static __inline__ void disable_dma(unsigned int dmanr)
{
if (dmanr<=3)
dma_outb(dmanr | 4, DMA1_MASK_REG);
else
dma_outb((dmanr & 3) | 4, DMA2_MASK_REG);
}
/* Clear the 'DMA Pointer Flip Flop'.
* Write 0 for LSB/MSB, 1 for MSB/LSB access.
* Use this once to initialize the FF to a known state.
* After that, keep track of it. :-)
* --- In order to do that, the DMA routines below should ---
* --- only be used while holding the DMA lock ! ---
*/
static __inline__ void clear_dma_ff(unsigned int dmanr)
{
if (dmanr<=3)
dma_outb(0, DMA1_CLEAR_FF_REG);
else
dma_outb(0, DMA2_CLEAR_FF_REG);
}
/* set mode (above) for a specific DMA channel */
static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
{
if (dmanr<=3)
dma_outb(mode | dmanr, DMA1_MODE_REG);
else
dma_outb(mode | (dmanr&3), DMA2_MODE_REG);
}
/* Set transfer address & page bits for specific DMA channel.
* Assumes dma flipflop is clear.
*/
static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
{
if (dmanr <= 3) {
dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
} else {
dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
}
}
/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
* a specific DMA channel.
* You must ensure the parameters are valid.
* NOTE: from a manual: "the number of transfers is one more
* than the initial word count"! This is taken into account.
* Assumes dma flip-flop is clear.
* NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
*/
static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
{
count--;
if (dmanr <= 3) {
dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
} else {
dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
}
}
/* Get DMA residue count. After a DMA transfer, this
* should return zero. Reading this while a DMA transfer is
* still in progress will return unpredictable results.
* If called before the channel has been used, it may return 1.
* Otherwise, it returns the number of _bytes_ left to transfer.
*
* Assumes DMA flip-flop is clear.
*/
static __inline__ int get_dma_residue(unsigned int dmanr)
{
unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
: ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
/* using short to get 16-bit wrap around */
unsigned short count;
count = 1 + dma_inb(io_port);
count += dma_inb(io_port) << 8;
return (dmanr<=3)? count : (count<<1);
}
/* These are in kernel/dma.c: */
extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
extern void free_dma(unsigned int dmanr); /* release it again */
/* These are in arch/m68k/apollo/dma.c: */
extern unsigned short dma_map_page(unsigned long phys_addr,int count,int type);
extern void dma_unmap_page(unsigned short dma_addr);
#endif /* _ASM_APOLLO_DMA_H */