aa44ef4d43
Adds core support for the ST-Ericsson U8500 platform. It supports memory mappings, binds to the existing modules like GIC, SCU, TWD and local timers and sets up the infrastructure for the secondary core. Reviewed-by: Alessandro Rubini <rubini@unipv.it> Reviewed-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com> Acked-by: Andrea Gallo <andrea.gallo@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
159 lines
3.8 KiB
C
159 lines
3.8 KiB
C
/*
|
|
* Copyright (C) 2008-2009 ST-Ericsson
|
|
*
|
|
* Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2, as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
*/
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/io.h>
|
|
#include <linux/amba/bus.h>
|
|
#include <linux/amba/pl022.h>
|
|
#include <linux/spi/spi.h>
|
|
|
|
#include <asm/localtimer.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
|
|
#include <plat/mtu.h>
|
|
|
|
#include <mach/hardware.h>
|
|
#include <mach/setup.h>
|
|
|
|
#define __MEM_4K_RESOURCE(x) \
|
|
.res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
|
|
|
|
/* These are active devices on this board */
|
|
static struct amba_device uart0_device = {
|
|
.dev = { .init_name = "uart0" },
|
|
__MEM_4K_RESOURCE(U8500_UART0_BASE),
|
|
.irq = {IRQ_UART0, NO_IRQ},
|
|
};
|
|
|
|
static struct amba_device uart1_device = {
|
|
.dev = { .init_name = "uart1" },
|
|
__MEM_4K_RESOURCE(U8500_UART1_BASE),
|
|
.irq = {IRQ_UART1, NO_IRQ},
|
|
};
|
|
|
|
static struct amba_device uart2_device = {
|
|
.dev = { .init_name = "uart2" },
|
|
__MEM_4K_RESOURCE(U8500_UART2_BASE),
|
|
.irq = {IRQ_UART2, NO_IRQ},
|
|
};
|
|
|
|
static void ab4500_spi_cs_control(u32 command)
|
|
{
|
|
/* set the FRM signal, which is CS - TODO */
|
|
}
|
|
|
|
struct pl022_config_chip ab4500_chip_info = {
|
|
.lbm = LOOPBACK_DISABLED,
|
|
.com_mode = INTERRUPT_TRANSFER,
|
|
.iface = SSP_INTERFACE_MOTOROLA_SPI,
|
|
/* we can act as master only */
|
|
.hierarchy = SSP_MASTER,
|
|
.slave_tx_disable = 0,
|
|
.endian_rx = SSP_RX_MSB,
|
|
.endian_tx = SSP_TX_MSB,
|
|
.data_size = SSP_DATA_BITS_24,
|
|
.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
|
|
.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
|
|
.clk_phase = SSP_CLK_SECOND_EDGE,
|
|
.clk_pol = SSP_CLK_POL_IDLE_HIGH,
|
|
.cs_control = ab4500_spi_cs_control,
|
|
};
|
|
|
|
static struct spi_board_info u8500_spi_devices[] = {
|
|
{
|
|
.modalias = "ab4500",
|
|
.controller_data = &ab4500_chip_info,
|
|
.max_speed_hz = 12000000,
|
|
.bus_num = 0,
|
|
.chip_select = 0,
|
|
.mode = SPI_MODE_0,
|
|
.irq = IRQ_AB4500,
|
|
},
|
|
};
|
|
|
|
static struct pl022_ssp_controller ssp0_platform_data = {
|
|
.bus_id = 0,
|
|
/* pl022 not yet supports dma */
|
|
.enable_dma = 0,
|
|
/* on this platform, gpio 31,142,144,214 &
|
|
* 224 are connected as chip selects
|
|
*/
|
|
.num_chipselect = 5,
|
|
};
|
|
|
|
static struct amba_device pl022_device = {
|
|
.dev = {
|
|
.coherent_dma_mask = ~0,
|
|
.init_name = "pl022",
|
|
.platform_data = &ssp0_platform_data,
|
|
},
|
|
.res = {
|
|
.start = U8500_SSP0_BASE,
|
|
.end = U8500_SSP0_BASE + SZ_4K - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
.irq = {IRQ_SSP0, NO_IRQ },
|
|
/* ST-Ericsson modified id */
|
|
.periphid = SSP_PER_ID,
|
|
};
|
|
|
|
static struct amba_device *amba_devs[] __initdata = {
|
|
&uart0_device,
|
|
&uart1_device,
|
|
&uart2_device,
|
|
&pl022_device,
|
|
};
|
|
|
|
static void __init u8500_timer_init(void)
|
|
{
|
|
#ifdef CONFIG_LOCAL_TIMERS
|
|
/* Setup the local timer base */
|
|
twd_base = __io_address(U8500_TWD_BASE);
|
|
#endif
|
|
/* Setup the MTU base */
|
|
mtu_base = __io_address(U8500_MTU0_BASE);
|
|
|
|
nmdk_timer_init();
|
|
}
|
|
|
|
static struct sys_timer u8500_timer = {
|
|
.init = u8500_timer_init,
|
|
};
|
|
|
|
static void __init u8500_init_machine(void)
|
|
{
|
|
int i;
|
|
|
|
/* Register the active AMBA devices on this board */
|
|
for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
|
|
amba_device_register(amba_devs[i], &iomem_resource);
|
|
|
|
spi_register_board_info(u8500_spi_devices,
|
|
ARRAY_SIZE(u8500_spi_devices));
|
|
|
|
u8500_init_devices();
|
|
}
|
|
|
|
MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
|
|
/* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
|
|
.phys_io = U8500_UART2_BASE,
|
|
.io_pg_offst = (IO_ADDRESS(U8500_UART2_BASE) >> 18) & 0xfffc,
|
|
.boot_params = 0x100,
|
|
.map_io = u8500_map_io,
|
|
.init_irq = u8500_init_irq,
|
|
/* we re-use nomadik timer here */
|
|
.timer = &u8500_timer,
|
|
.init_machine = u8500_init_machine,
|
|
MACHINE_END
|